Please register to participate in our discussions with 2 million other members - it's free and quick! Some forums can only be seen by registered members. After you create your account, you'll be able to customize options and access all our 15,000 new posts/day with fewer ads.
Yes, on that truck they would have to. And the other poster is right, they don't have to pull it out completely, but they will have to pick it up by about 6" to get the pan off and replace the gasket. There is a crossmember on several Ford models that passes right under the oil pan, so there is no clearance to get it off without lifting the engine up. I happen to know this because the oil pan gasket needs to be replaced on my 96 Ford truck right now, and when I crawled under there to get at it, I found that it couldn't be done without hoisting the engine.
Yes, on that truck they would have to. And the other poster is right, they don't have to pull it out completely, but they will have to pick it up by about 6" to get the pan off and replace the gasket. There is a crossmember on several Ford models that passes right under the oil pan, so there is no clearance to get it off without lifting the engine up. I happen to know this because the oil pan gasket needs to be replaced on my 96 Ford truck right now, and when I crawled under there to get at it, I found that it couldn't be done without hoisting the engine.
I once bought a car at a car auction for a low price. Similiar model (poorer condition) went for a higher price a few mins later. Thought that strange but after driving the car home looked underneath and saw the trans leaking fluid...shoot I thought...bad tranny. Thats probably why it sold cheap.
Jacked the car up and tightened some loose bolts snugly...stopped the leak and that car was a winner from that day on...no problems at all.
Later on found out the old couple had traded it in on a new Toyota at a dealearship thinking their trans was going out. Someone gave a bad diagnosis or snow job.
It is hard to snap a pan bolt using a small hand ratchet...using a torque wrench would be stupid.
I'm familiar with raising the engine off the motor mounts/frame enough for the pan to clear the sump and rods (been there and done that).
What's the condition of the gasket where the bolts are missing? Is the gasket bulging out? If so, just replacing the bolts won't help. To seal it properly, the gasket will have to be replaced.
Also, are you sure the bolts aren't broken off in the block?
I,m not sure, will be taking to my mechanic Monday to check out. Right now just going on what dealer said.
Pan bolts just don't fall out. Someone (a previous owner) started to pull the pan and said F it! Either that or he broke them off in the block. If so, don't panic, that is what they make easy outs or screw extractors for. Those bolts should all be torqued following a torque sequence in a service manual. Most are in two or three steps. Buy the manual for best results. Use a digital torque wrench if possible. I would take out another bolt that is easily accessible and use it as a pattern to get two new ones to match. Try putting them all back in and see if it leaks. If not, you have fixed it. If so, the pan will have to be removed and a new gasket installed. I would recommend The Right Stuff or a rubber gasket. Cork sucks and always seems to develop leaks over time. That cross member is in the way of the pan on a '95. I used to have a '96 and it was the same way. You have to lift or pull the engine to clear it. The pick-up won't clear otherwise. http://www.permatex.com/products/aut...sket_Maker.htm
Great info. I went to dealer and a parts shop and both said you have to take out another bolt so as to match one of theirs. Thats why I will be letting my mech. fix it. Seems more to it than inserting 2 bolts. Also I am disabled so my wife would be doing the work.
Please register to post and access all features of our very popular forum. It is free and quick. Over $68,000 in prizes has already been given out to active posters on our forum. Additional giveaways are planned.
Detailed information about all U.S. cities, counties, and zip codes on our site: City-data.com.