- Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness (corrected on site)
Observation: The chlorine chemical sanitizer used in the sanitizing solution does not meet the criteria specified under section 7-204.11, is not used in accordance with the EPA-approved manufacturer's label use instructions, or does not have a minimum temperature based on the concentration and pH of the solution. Chlorine sanitizer was empty at ware washing machine.
Correction: A chlorine chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at exposure times specified under paragraph 4-703.11(C) shall meet the criteria specified under section 7-204.11 Sanitizers, Criteria, shall be used in accordance with the EPA-approved manufacturer's label use instructions, and shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The food-contact surfaces of soda gun nozzles are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station at the kitchen is being used as a dump station. Corrected by instruction.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Hand Drying Provision (corrected on site) (repeated violation)
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
|
06/04/2015 | Risk Factor | |
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Food preparation and dispensing utensils are improperly stored. Utensils were stored in container of water on stove that was at 120 F.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Chicken cutlets wer at 120 F on prep line. Removed.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Curry sauces, cooked spinach, chickpeas, etc., in walk in, prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment and Utensils/Durability and Strength
Observation: The Black and Decker blender and the Cuisinart food processor are home standard.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Good Repair and Proper Adjustment
Observation: The shelf under prep table in kitchen was observed with accumulation of rust.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: Intake and exhaust air ducts in kitchen are not clean and/or filters are not changed.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
|
02/05/2015 | Routine | |
| No violation noted during this evaluation. | 11/10/2014 | Other | |
2 door cook's prep refrigerator was not maintaining an internal ambient temperature of 41 F or less.
Roach activity observed at ware washing machine area.
Pest control records observed. Records show service to establishment occurring approximately 2x/month.
Areas under, around, and inside equipment were observed in need of cleaning.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Items in the 2 door cook's prep unit were holding at greater than 41 F, including chicken curry at 48 F, lamb curry at 48 F, sliced tomatoes at 49 F. Items discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site) (repeated violation)
Observation: Several prepared items in walk in, including samosas, chicken curry, spinach pakora, samosas, etc., prepared and held in the food establishment for more than 24 hours were not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded. Corrected by instruction.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact equipment surface(s) of the carrot peeler and the knife stored between refrigeration units is(are) not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Poisonous or Toxic Materials/Common Name/Working Containers (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Poisonous or Toxic Materials/Restrictions/Presence and Use (corrected on site)
Observation: Raid Ant and Roach spray is not required for the operation and maintenance of the food establishment. Removed.
Correction: Only those poisonous or toxic materials that are required for the operation and maintenance of the establishment, such as for the cleaning and sanitizing of equipment and utensils and the control of insects and rodents, shall be allowed in the food establishment. This section does not apply to packaged poisonous or toxic materials that are for retail sale. The presence in the establishment of poisonous or toxic materials that are not required for the maintenance and operation of the establishment represents an unnecessary risk to both employees and consumers. Preserving food safety depends in part on the appropriate and proper storage and use of poisonous or toxic materials that are necessary to the maintenance and operation of a food establishment. Even those that are necessary can pose a hazard if they are used in a manner that contradicts the intended use of the material as described by the manufacturer on the material's label. If additional poisonous or toxic materials are present, there is an unwarranted increased potential for contamination due to improper storage (e.g., overhead spillage that could result in the contamination of food, food-contact surfaces, or food equipment) or inappropriate application.
|
10/07/2014 | Risk Factor | |
All violations from previous inspection have been corrected.
No violation noted during this evaluation. | 06/26/2014 | Follow-up | |
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Onion sauce cooked yesterday (58 F) was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less. Food discarded.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Various foods observed cold holding at improper temperatures of 45 F to 48 F in the cook's prep line refrigerator (cauliflower (cooked) 46 F, lamb 48 F, chicken 46 F, spinach 46 F, garlic spread 48 F). Foods were discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Foods prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded. Corrected by instruction.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Surfaces of the soda gun at the bar are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers (spray bottles) used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
06/16/2014 | Risk Factor | |
- Responsibilities of Owner or Proprietor
Observation: Absence of no-smoking signs or international no-smoking signs in non-smoking area.
Correction: Post no-smoking signs or international no-smoking signs in the non-smoking area.
These can be found online at www.vdh.virginia.gov/breatheasy
- Package Integrity
Observation: A severely dented can was observed on the shelving rack. Properly segregate/label not to use
Correction: return for credit or discard.
- Food Storage Containers, Identified with Common Name of Food (corrected on site)
Observation: Container of salt is not identified with the common name of the food.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- In-Use Utensils, Between-Use Storage
Observation: Food preparation and dispensing utensils are improperly stored. A cup was observed in the bar ice. Bowls were observed in the flour bag and rice bin.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Food Storage/Preventing Contamination from the Premises
Observation: An open bag of flour is not protected from contamination. Store in an approved reusable container.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Food Storage, Prohibited Areas
Observation: Food storage under sewer lines. Packets of salt and pepper stored under the front counter hand-sink drain pipe.
Correction: Relocate food storage to an approved area or shield the sewer lines to intercept potential drips.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Cheese in the top portion of the cook's prep refrigerator cold holding at the improper temperature of 50 F. The cheese was relocated to the bottom portion of the refrigerator.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface of the cook's wooden wall shelf and aluminum foil used to line some shelves are not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Food-Contact Surfaces/Cleanability
Observation: The food-contact surface of a large steel bowl and the "Oster" blender are not smooth, free of breaks, open seams, cracks, chips, inclusions, pits, similar imperfections, finished to have smooth welds and joints, and/or accessible for cleaning and inspection by an approved method.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Equipment/Good Repair and Proper Adjustment
Observation: The "Frigidaire" chest freezer interior lid, the "Maximum" left interior door panel, and the top of the Hobart mixer are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The wet stacked cutting boards and the can opener are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surface of the kitchen shelving and the "Maximum" refrigerator door handles are not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. The dishmachine was not ejecting sanitizer 50-100 ppm. Sanitize food-contact surfaces in the three compartment until the dishmachine is repaired.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Plumbing System/Maintained in Good Repair
Observation: The mop/service sink has no hot water.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Refuse/Covering Receptacles
Observation: Receptacles and/or waste handling units for refuse, recyclables, and/or returnables kept outside the food establishment are not kept covered with tight-fitting lids.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
- Light Bulbs, Protective Shielding
Observation: The light bulbs over the customer display steamtable are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Handwashing Cleanser, Availability
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink (bar).
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
- Hand Drying Provision (repeated violation)
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Handwashing Signage (repeated violation)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees (bar).
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 50 foot candles where a food employee is working with food (cook-line hood ventilation system
Correction: 2-3 lights out).
- Controlling Pests
Observation: An immature German cockroach was found in the front counter cabinetry. Remove cardboard from the facility.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material (spray bottle) .
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
01/14/2014 | Routine | |
- Refuse/Toilet Room Receptacle, Covered
Observation: There is no covered receptacle in the toilet room used by females.
Correction: A toilet room used by females shall be provided with a covered receptacle for sanitary napkins. Garbage containers should be available wherever garbage is generated to aid in the proper disposal of refuse.
- Hand Drying Provision
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Intensity/Lighting
Observation: One light out at hood.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
|
05/31/2013 | Pre-Opening | |
Restroom closed during renovation. CFM stated that customers have access to Rooftop Restaurant restrooms.
"Keep It Clean" DES poster provided.
- Critical: Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An open beverage container and/or a closed beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: Cooked lamb at 53oF, chicken tikka at 47oF, in Maximum 2 door uprt.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment and Utensils/Durability and Strength
Observation: The Panasonic and Kenmore microwaves are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Good Repair and Proper Adjustment
Observation: The door handles on the Maximum 1 door uprt freezer were in disrepair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surface of the shelving under prep tables were not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station at the kitchen is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
|
04/10/2013 | Routine | |
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical)
Observation: The food contact surface of the soda nozzles, knives on rack and ice machine plate is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food. Lights under hood are not in working order.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
|
09/02/2011 | Routine | |
Restaurant representatives - add corrected or new information about Delhi Dhaba Restaurant, 2424 Wilson Blvd, Arlington, VA 22201 »