- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Ready to eat food containers inside the walk-in cooling unit were not dated.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
|
10/27/2014 | Risk Factor | |
1. Do not use hand washing sink to dump coffee at night.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Sliced provolone cheese cold holding at the improper temperature of 47F in a plastic container with paper towels on top portion of "True" 3-dr prep refrigerator (uncovered, relocated in the lower area)
Correction: milk (60F), yogurt (59F), cold-cut sandwiches (55F) and cut melons (55F) observed at improper cold holding temperature in "Bev Air 1-dr refrigerator in Potomac Perk kitchen (all foods were discarded); and shredded cheddar (49F) and individual packs of half-n-half (65) were found at improper cold holding temperature in the employee lounge lunch buffet (discarded). Containers of Hollandaise sauce observed at 54F (discarded) inside "True" sliding dr refrigerator in main kitchen.;Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Surfaces of the fountain soda nozzles are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
|
06/11/2014 | Risk Factor | |
- Food Storage/Preventing Contamination from the Premises
Observation: Stored food is not protected from contamination. Cases of food stored on floor in walk in freezer.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Sliced portioned deli meats in True 3 door prep, prepared and held in the food establishment for more than 24 hours were not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface(s) of the foil lining the top of the cabinet at server station is(are) not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Food-Contact Surfaces/Cleanability
Observation: The food-contact surface(s) of a couple of cutting boards is(are) not smooth, free of breaks, open seams, cracks, chips, inclusions, pits, similar imperfections, finished to have smooth welds and joints, and/or accessible for cleaning and inspection by an approved method.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Equipment/Good Repair and Proper Adjustment
Observation: The 2 part prep sink is no longer connected to wall.
Some of the bread drawers that are used for storage were no longer functional.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact equipment surface(s) of the slicer blade assembly is(are) not clean to sight and touch. Broken down for cleaning.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Cleaned equipment and utensils, laundered linens, and single-service and/or single-use articles are improperly stored. Dish rack of clean dishes was stored directly on floor.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Plumbing System/Maintained in Good Repair
Observation: The main floor mop sink had no water supply.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Hand Drying Provision (corrected on site)
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Intensity/Lighting
Observation: The light is burned out in the True 2 door uprt glass unit.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Intensity/Lighting
Observation: A light was burned out over the cook line.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing
Observation: The corner break room had some wall damage at paneled area.
Some floor damage observed at entry way to dry storage room.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Drying Mops
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
|
02/24/2014 | Routine | |
1. Make sure to cool cooked foods properly or if not intended to be used again, trash them.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Roast beef (60F), Ham (63F) and Pasta salad (49F) were observed at improper cold holding temperature in "Traulsen" 3-door refrigerator.
Correction: (discarded) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency (corrected on site) (repeated violation)
Observation: Surfaces of the fountain soda nozzles are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
|
10/04/2013 | Risk Factor | |
1. Keeping wiping towels in sanitizer buckets.
2. Consider repairing/replacing temperature and pressure gauges of high-temp warewashing machine.
3. De-lime and clean both interior and exterior of the warewaashing machine.
4. Defrost and clean chest freezers.
5. Make sure to label all the chemical spray bottles properly.
High-temp warewashing machine: OK
- Critical: Safe, Unadulterated, and Honestly Presented/Condition (corrected on site)
Observation: Moldy grated parmesan cheese found in "True" sliding door refrigerator is not safe, unadulterated, and/or honestly presented.
Correction: Food shall be safe, unadulterated, and, as specified under section 3-601.12, honestly presented.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Black beans (49F), Rice (49F) and Potato salad (49F), all prepared on or before 06/16/2013 and found in "True" sliding door refrigerator were observed at improper cold holding temperature.
Correction: (discarded) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency (corrected on site) (repeated violation)
Observation: Surfaces of the soda fountain nozzles are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
|
06/20/2013 | Risk Factor | |
- Critical: Package Integrity (corrected on site)
Observation: A couple of dented cans were found on the can rack.
Correction: Food packages shall be in good condition and protect the integrity of the contents so that food is not exposed to adulteration or potential contaminants.
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: An employee was observed contacting ready-to-eat (RTE) food (lemons) with their bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph (D) of this section, food employees may not contact exposed, RTE food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Food Storage/Preventing Contamination from the Premises (repeated violation)
Observation: Food stored in a commonly wet or soiled location [on floor in walk-in freezer].
Correction: Protect food from contamination by storing the food in a clean and dry location.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Half 'n' half at customer counter pitchercold holding at the improper temperature of 46oF.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment/Fixed, Spacing or Sealing (repeated violation)
Observation: The banquet kitchen dish sprayer counter is not sealed to its adjoining wall.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment/Fixed, Elevation or Sealing
Observation: Shelving in the banquet kitchen bottom shelves do not provide at least a 6 inch clearance between the floor and the equipment.
Correction: Floor-mounted equipment that is not easily movable shall be sealed to the floor or elevated on legs that provide at least a 15 centimeter (6 inch) clearance between the floor and the equipment. If no part of the floor under the floor-mounted equipment is more than 15 centimeters (6 inches) from the point of cleaning access, the clearance space may be only 10 centimeters (4 inches). This section does not apply to display shelving units, display refrigeration units, and display freezer units located in the consumer shopping areas of a retail food store, if the floor under the units is maintained clean. The inability to adequately or effectively clean areas under equipment could create a situation that may attract insects and rodents and accumulate pathogenic microorganisms that are transmissible through food. The effectiveness of cleaning is directly affected by the ability to access all areas to clean fixed equipment. It may be necessary to elevate the equipment. When elevating equipment is not feasible or prohibitively expensive, sealing to prevent contamination is required.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The "Traulsen" 3-door refrigerator has some rusty shelves. The walk-in refrigerator ceiling is sagging with tape in-between the seams. Several toastmaster drawers are not in good repair or used anymore.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical)
Observation: The slicer is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency
Observation: Surfaces of the soda fountain and juice dispensing machine are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: Some shelving in the walk-in refrigerator is not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site)
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in the hot water mechanical operations by being cycled through equipment that is properly set up and/or achieving a utensil surface temperature of 160°F as measured by an irreversible registering temperature indicator [1st Floor kitchen dishmachine final rinse temperature was not reaching a minimum 180oF and the pressure gauge was reading above 25 psi during the final rinse].
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in hot water mechanical operations by being cycled through equipment that is set up as specified under sections 4-501.15, 4-501.112, and 4-501.113 and achieving a utensil surface temperature of 71°C (160°F) as measured by an irreversible registering temperature indicator. When surface temperatures of utensils passing through warewashing machines using hot water for sanitizing do not reach the required 71°C (160°F), it is important to understand the factors affecting the decreased surface temperature. A comparison should be made between the machine manufacturer's operating instructions and the machine's actual wash and rinse temperatures and final rinse pressure. The actual temperatures and rinse pressure should be consistent with the machine manufacturer's operating instructions and within limits specified in sections 4-501.112 and 4-501.113. If either the temperature of pressure of the final rinse spray is higher than the specified upper limit, spray droplets may disperse and begin to vaporize resulting in less heat delivery to utensil surfaces. Temperatures below the specified limit will not convey the needed heat to surfaces. Pressures below the specified limit will result in incomplete coverage of the heat-conveying sanitizing rinse across utensil surfaces.
- Handwashing Sink/Using/Operation and Maintenance
Observation: The handwashing station by the cashier is being used to clean equipment and utensils.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Plumbing System/Maintained in Good Repair
Observation: The banquet & 1st floor kitchen 3-part sinks middle and right stoppers are not maintained good repair.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Hand Drying Provision (corrected on site)
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees [cook-line handsink].
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Intensity/Lighting (corrected on site)
Observation: The light intensity is below 50 foot candles where a food employee is working with food [two hood lights out].
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Intensity/Lighting
Observation: The light intensity is below 20 foot candles in the 1st floor kitchen "True" sliding door refrigerator.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Physical Facilities/Repairing
Observation: There is a hole in the wall under/by the 1st floor kitchen dishwashing machine. The pipes are sealed to their adjoining walls by the dishmachine, 3-part sink, and 2-part sink in the 1st floor kitchen. There are some missing/damaged wall tiles by the 3-part sink in the 1st floor kitchen. There is a crack in the corner of the wall by the 1st floor kitchen dishmachine, and in the food storage room. There are a couple little damaged ceiling tiles above the 1st floor dishmachine. The walls around the doors to the dumpster area are not maintained in good repair. There are some damage and missing floor tiles in the food storage room. The ceiling in the dry goods storage room is not maintained in good repair. The banquet kitchen wood wall is not maintained in good repair. The walls are not sealed around the booster heater pipes in the banquet kitchen.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests
Observation: Dead German cockroach was observed on the floor in the 1st floor kitchen dishwashing area. Fruit fly was observed in the banquet kitchen.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Cleaning, Frequency and Restrictions
Observation: The walls and floors in the dishwashing area of the 1st floor kitchen are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
01/25/2013 | Routine | |
Restaurant representatives - add corrected or new information about Holiday Inn At Key Bridge Potomac Perk,Main Kitchen 1st Fl, Banquet Kitchen 2nd Fl, Employee Lounge, 1900 N Fort Myer Dr, Arlington, VA 22209 »