- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: The ice cream chest freezer is not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The inside of the deep fryers need cleaning.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floor behind the cooking line needs cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Drying Mops
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
|
01/13/2016 | Routine | |
The bar 3-part sink missing the stoppers and was not set-up.
- Package Integrity (corrected on site)
Observation: A water chestnuts dented can was found inside the storage room, discarded.
Correction: Food packages shall be in good condition and protect the integrity of the contents so that food is not exposed to adulteration or potential contaminants.
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: The blender mix cup was not sanitized after cleaning, the 3-part sink at the bar were the blender mix cup is cleaned and sanitized had no sanitizer.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
|
09/22/2015 | Risk Factor | |
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention
Observation: An employee was eating in the kitchen while he was handling food and cleaning dishes.
Correction: An employee shall eat, drink, or use any form of tobacco only in designated areas where the contamination of exposed food
- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Several ready to eat food containers stored in the walk-in cooling unit prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing station at the cooking line is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
|
04/07/2015 | Risk Factor | |
- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Several ready to eat food containers prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment and Utensils/Durability and Strength
Observation: The chest freezer is not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Cutting Surfaces (repeated violation)
Observation: The surfaces of the small cutting boards are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The nonfood-contact surfaces of the deep fryers need cleaning.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Cleaning, Frequency and Restrictions
Observation: The floor behind the cooking line and the edges need cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: The bathrooms vents are dusty.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
|
02/09/2015 | Routine | |
Information on non-continuous cooking was given to the CFM.
Maintain bean sprouts at 41 F or less.
- Person In Charge/Duties/Employees Observing Received Foods (corrected on site)
Observation: Foods are not visibly observed upon their receipt. Corrected by instruction.
Correction: The person in charge shall ensure that employees are visibly observing foods as they are received to determine that they are from approved sources, delivered at the required temperatures, protected from contamination, unadultered, and accurately presented, by routinely monitoring the employees' observations and periodically evaluating foods upon their receipt.
- Person in Charge/Duties/Employees Sanitizing Equipment (corrected on site)
Observation: The person in charge could not explain how to setup the 3 compartment sink (wash, rinse, & sanitize). Corrected by instruction.
Correction: The person in charge shall ensure that employees are properly sanitizing cleaned multiuse equipment and utensils before they are reused, through routine monitoring of solution temperature and exposure time for hot water sanitizing, and chemical concentration, pH, temperature, and exposure time for chemical sanitizing.
- Non-Continuous Cooking for Raw Animal Foods
Observation: A written procedures has not been approved by the regulatory authority to non-continuously cook raw animal foods(chicken, pork, and shrimp).
Correction: Raw animal foods that are cooked using a non-continuous cook process shall be prepared and stored according to written procedures that: (1) have obtained prior approval from the regulatory authority
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Bean sprouts on the counter during lunch cold holding at the improper temperature of 51ºF. The bean sprouts were returned to refrigerator.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site)
Observation: Dumplings and shrimp rolls prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: A few food storage containers on the drying rack are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
|
09/18/2014 | Risk Factor | |
A service invoice was provided for the refrigerator repairs. Mussel tags observed with the shellstock (MA 3257 SS). Remember to date the tag for when the last of the shellstock is used and to keep tags on file for 90 days. Dishmachine chlorine sanitizer concentration was tested using the provided test strips.
No violation noted during this evaluation. | 05/28/2014 | Follow-up | |
The product in the walk-in refrigerator and the 3-door prep unit were observed cold holding at <41 degrees Fahrenheit. Provide the refrigeration unit repair invoices to the health department. Repair invoices can be faxed or emailed. Health department contact information was left with the person in charge. The chlorine sanitizer in the mechanical dishmachine was observed at proper concentration. Ready-to-eat foods in the walk-in were observed date labeled. A recheck of the facility will be conducted on or about 05/27/14.
No violation noted during this evaluation. | 05/16/2014 | Other | |
Cook-line hand-sink observed slow to drain. The temperature in the walk-in refrigerator and the 3-door preparation unit appeared to be above 41 degrees Fahrenheit. A check of the refrigeration units will be conducted tomorrow 05/16/14. A follow-up will also conducted at a later date. The person in charge has contacted the repair company and will have the units serviced this afternoon or tomorrow. The dishmachine will also be serviced.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food after handling raw shrimp.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: Employee observed in the food preparation area.
Correction: An employee shall eat, drink, or use any form of tobacco only in designated areas where the contamination of exposed food
- Shellstock, Maintaining Identification
Observation: Shellstock tags observed not placed with the actual in-use shellstock.
Correction: Shellstock tags shall remain attached to the container in which the shellstock are received until the container is empty.
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Employee observed placing garnish in the final soup dish with his/her bare hand.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Pot of curry on the stove observed hot holding at improper temperature (107*F). Product was discarded by the person in charge.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Container of soup and cooked pork in the walk-in refrigerator observed cold holding at improper temperature (product was discarded by the person in charge). Raw scallops, raw shrimp, and rice noodles in the 3-door preparation unit observed cold holding at improper temperature (according to the person in charge the product had been recently prepped, the product was then placed on ice by the person in charge). Container of garlic in oil at the cook-line observed holding at improper temperature (product was placed under refrigeration).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site) (repeated violation)
Observation: Several ready-to-eat foods observed not properly dated (ex. curry, soups).
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized
Observation: Chlorine sanitizer in the mechanical dishmachine observed at 0 ppm (the person in charge will sanitize dishes/utensils in the 3-compartment sink until the machine has been repaired).
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Spray bottle chemical containers observed not properly labeled.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
05/15/2014 | Risk Factor | |
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Scoops were stored in standing water.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Linens and Napkins, Use Limitation (repeated violation)
Observation: Linens and/or napkins are used in contact with food.
Correction: Linens and napkins may not be used in contact with food unless they are used to line a container for the service of foods and the linens and napkins are replaced each time the container is refilled for a new customer. Because of their absorbency, linens and napkins used as liners that contact food must be replaced whenever the container is refilled. Failure to replace such liners could cause the linens or napkins to become fomites.
- Wiping Cloths, Use Limitation
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration
Correction: and/or not laundered daily.
- Thawing
Observation: Thawing raw chicken in standing water.
Correction: Time/temperature control for safety food shall be thawed: (A) Under refrigeration that maintains the food temperature at 5ºC (41ºF) or less
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Bean sprouts at 51 F, discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Some ready to eat food containers in the walk-in cooling unit were not dated.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The walk-in cooling unit shelves are rusted.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces (repeated violation)
Observation: The surfaces of the small cutting boards are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The kitchen hood is dirty (greasy).
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: One of the handwashing sink located at the cooking line had a plastic container inside and was not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Intensity/Lighting (repeated violation)
Observation: There is a light bulb out under the kitchen hood.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing (repeated violation)
Observation: The floor area on front of the dishwashing machine is damaged.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
|
01/23/2014 | Routine | |
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The following observed in need of repair:
- shelving is rusty where can opener is and in back area by ice machine.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
|
12/18/2013 | Follow-up | |
- Linens and Napkins, Use Limitation
Observation: Linen/paper towel lining food.
Correction: Linens and napkins may not be used in contact with food unless they are used to line a container for the service of foods and the linens and napkins are replaced each time the container is refilled for a new customer. Because of their absorbency, linens and napkins used as liners that contact food must be replaced whenever the container is refilled. Failure to replace such liners could cause the linens or napkins to become fomites.
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: Cardboard lining shelves.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment and Utensils/Durability and Strength
Observation: Papaya salad utensils are not food grade.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Good Repair and Proper Adjustment
Observation: The following observed in need of repair:
- chest freezer lid is cracked
- three door prep handle is broken
- catch pan at hood is missing
- shelving is rusty where can opener is, in walk-in and in back area by ice machine.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces
Observation: The surfaces of the bar cutting board is no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Warewashing Machine, Cleaning Frequency
Observation: The interior surfaces of the mechanical warewashing machine are soiled with (food debris, limescale) that may decrease the effectiveness of the unit.
Correction: Increase the frequency of cleaning or limescale deposit removal from the interior surfaces of the unit to maintain unit performance.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surface of the ice machine interior panel and equipment/utensils on shelf above rice cooker are not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Plumbing System/Maintained in Good Repair
Observation: No cold water at bar three compartment sink.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Light Bulbs, Protective Shielding
Observation: The light bulbs in the dish area are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Outer Openings, Protected
Observation: 1. Rear exit door does not shut properly.
2. Gap observed at bottom threshold of front doors.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Intensity/Lighting
Observation: Light is out in front of walk-in and one at the hood.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing
Observation: The following observed in need of repair:
- holes observed in wall by coffee machine
- floor of cook line and dish area is in poor repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions
Observation: The following observed in need of cleaning:
- floor under shelving where beer is stored
- drain by grease trap near cook line
- wall by grease trap near cook line
- hood piping
- floor under equipment
- crack between prep table and wall where rice cooker is stored
- dish dolleys.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
12/17/2013 | Pre-Opening | |
Restaurant representatives - add corrected or new information about Thaiphoon At Pentagon Row, 1301 S Joyce St D-4, Arlington, VA 22202 »