Follow-up to check hot water distribution.
Hot water was restored.
New hot water heater was installed.
Substantial compliance observed.
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 20 foot candles the Edesa 2 door refrigerator and in the hallway where the rice is stored.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Employee Accommodations/Designated Areas (repeated violation)
Observation: Lockers or other suitable facilities are not located in a designated room or area where contamination of food, equipment, utensils, linens, and/or single-service and single-use articles can not occur.
Correction: Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-service and single-use articles can not occur.
- Physical Facilities/Repairing (repeated violation)
Observation: The floor tiles in the kitchen and kitchen hall way are not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
|
02/01/2016 | Follow-up | |
* A follow-up will be conducted on Monday February 1, 2016.
The hood will be cleaned next week.
- Wiping Cloths, Use Limitation (corrected on site) (repeated violation)
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens (corrected on site) (repeated violation)
Observation: The thin yellow sushi menus are missing asterisks next to all items that are served raw or undercooked. The CFM will print new menus.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Water/Capacity/Quantity and Availability (corrected on site)
Observation: Hot water generation and distribution systems are not sufficient to meet the peak hot water demands throughout the establishment. A new hot water heater will be delivered and installed tomorrow.
Correction: Hot water generation and distribution systems shall be sufficient to meet the peak hot water demands throughout the food establishment. Hot water required for washing items such as equipment and utensils and employees' hands, must be available in sufficient quantities to meet demand during peak water usage periods. Booster heaters for warewashers that use hot water sanitizing are designed to raise the temperature of hot water to a level that ensures sanitization. If the volume of water reaching the booster heater is not sufficient or hot enough, the required temperature for sanitization can not be reached. Manual washing of food equipment and utensils is most effective when hot water is used. Unless utensils are clean to sight and touch, they cannot be effectively sanitized.
- Intensity/Lighting
Observation: The light intensity is below 20 foot candles the Edesa 2 door refrigerator and in the hallway where the rice is stored.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Employee Accommodations/Designated Areas
Observation: Lockers or other suitable facilities are not located in a designated room or area where contamination of food, equipment, utensils, linens, and/or single-service and single-use articles can not occur.
Correction: Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-service and single-use articles can not occur.
- Physical Facilities/Repairing
Observation: The floor tiles in the kitchen and kitchen hall way are not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
|
01/28/2016 | Routine | |
Remember to wash your hands frequently.
Email a copy of the updated parasite destruction letter to CIL.
*Provide chlorine sanitizer test strips.
Asterisks were added to the menu.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surfaces of a few containers on the drying shelf were not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
|
09/15/2015 | Risk Factor | |
*Do not store TCS foods in refrigerators that are not maintaining at temperature of 41 F or less.
*Do not receive TCS foods that are not 41 F or less/ 135 F or higher.
* Do not over stock prep refrigerators.
- Temperature/Specifications for Receiving (corrected on site) (repeated violation)
Observation: Rice noodles were observed received at 74ºF. Discarded.
Correction: Refrigerated, time/temperature control for safety foods shall be at a temperature of 5ºC (41ºF) or below when received. If a temperature other than 5ºC (41ºF) for a time/temperature control for safety food is specified in law governing its distribution, such as laws governing milk and molluscan shellfish, the food may be received at the specified temperature.
- Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: A bowl of raw chicken was observed sitting on sliced lettuce in the prep refrigerator.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: TCS foods in the prep refrigerator and the sushi display were observed improperly cold holding. The temperature was adjusted in the sushi display. The gaskets have been ordered for the 2 door prep refrigerator.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens (repeated violation)
Observation: Asterisks are missing on all menu item foods offered raw. The asterisk for the consumer advisory statement is the same for the brown rice option. According to the owner the wrong menu was printed again.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
|
05/18/2015 | Risk Factor | |
Substantial compliance was observed during this follow-up.
Email corrected sushi menu to CIL. An updated menu was sent on 1/5.
- Nonfood-Contact Surfaces/Nonabsorbent (repeated violation)
Observation: The nonfood-contact surface of the rope holding the pre-spray hose up is not nonabsorbent, and smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: The crock-pot, microwave, and "Black and Decker" toaster oven are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: Handles are missing on the crock-pot and the one door prep refrigerator.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
|
02/03/2015 | Follow-up | |
Correct all repeat and priority violations within 10 days (February 2, 2015).
*Wash hands not gloves.
- Cleaning Procedure/Hands and Arms (corrected on site)
Observation: Food employees are washing their gloves and not their hands.
Correction: Food employees shall clean their hands and exposed portions of their arms, including surrogate prosthetic devices for hands or arms for at least 20 seconds, using a cleaning compound in a handwashing sink that is equipped as specified under section 5-202.12 and Subpart 6-301. If approved and capable of removing the types of soils encountered in the food operations involved, an automatic handwashing facility may be used by food employees to clean their hands or surrogate prosthetic devices.
- Hands and Arms/Where to Wash (corrected on site)
Observation: A food employee was observed cleaning their hands in warewashing sink and at the wash table.
Correction: Food employees shall clean their hands in a handwashing sink or approved automatic handwashing facility and may not clean their hands in a sink used for food preparation or warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste.
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An employee was eating and drinking in an area where contamination of exposed food or clean equipment may occur.
Correction: An employee shall eat, drink, or use any form of tobacco only in designated areas where the contamination of exposed food
- Contamination from Hands/Preventing Contamination by Employees (corrected on site) (repeated violation)
Observation: Food employee contacting exposed RTE food (sushi rolls and spring rolls) with bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Wiping Cloths, Use Limitation (corrected on site)
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Cooling Methods (corrected on site)
Observation: Methods used for cooling hot dumplings in a large container can not be accomplished with the time and temperature criteria.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Cooked vegetables and eel were observed hot holding at improper temperatures. Reheated.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: TCS foods on the counters and prep tables were observed cold holding at improper temperatures. Discarded or returned to refrigeration.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Time Public Health Control/Time - Maximum up to 4 Hours/Marked
Observation: The sushi rice for which time only, rather than time in conjunction with temperature control, is not properly labeled to indicate the time it shall be discarded.
Correction: If time only, rather than time in conjunction with temperature control, up to a maximum of 4 hours, is used as the public health control: The food shall be marked or otherwise identified to indicate the time that is 4 hours past the point in time when the food is removed from temperature control.
- Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: 1. Asterisks are missing on all menu item foods offered raw. 2. The asterisk for the consumer advisory statement is the same for the brown rice option.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface of the rope holding the pre-spray hose up is not nonabsorbent, and smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: The crock-pot, microwave, and "Black and Decker" toaster oven are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Fixed, Spacing or Sealing
Observation: The handwashing sink and the wash table are not sealed to the adjoining walls.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: Handles are missing on the crock-pot and the one door prep refrigerator.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surface of the hood is not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing (repeated violation)
Observation: Cleaned equipment and utensils are improperly stored near the handwashing sink that is missing a splash guard.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sinks located in sushi area and warewashing area are not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Permit to Operate/Responsibilities of Permit Holder
Observation: The 2015 permit is not posted in a location in the food establishment that is conspicuous to consumers. 2014 is posted on the wall.
Correction: Upon acceptance of the permit issued by the regulatory authority, the permit holder in order to retain the permit shall post the permit in a location in the food establishment that is conspicuous to consumers.
|
01/22/2015 | Routine | |
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An open beverage container and/or a closed beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed. Corrected by instruction.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Bean sprouts cold holding at the improper temperature of 77 F. Food discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: The Oyster blender, Rival crock pot, small toaster oven and Emerson microwave are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: Observed the plate inside ice machine is being held up with rusted screws which do not maintain ice machine in a state of repair and condition that meets the requirements of materials for construction and repair and/or design. Observed the sushi display case damaged and held together with tape.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing (repeated violation)
Observation: Observed cleaned equipment and utensils stored next to handwashing sink where they are exposed to splash from employee handwashing.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located across from dish machine is used for purposes other than handwashing. Observed towel and chemical spray bottle in sink.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers (spray bottles) used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Critical: Food Manager Certificate and Responsibility (corrected on site)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager. Corrected during inspection manager arrived during inspection.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
08/18/2014 | Follow-up | |
- Critical: Temperature/Specifications for Receiving
Observation: Refrigerated bean sprouts (70 F- 72 F) received at a temperature above 41ºF.
Correction: Refrigerated, time/temperature control for safety foods shall be at a temperature of 5ºC (41ºF) or below when received. If a temperature other than 5ºC (41ºF) for a time/temperature control for safety food is specified in law governing its distribution, such as laws governing milk and molluscan shellfish, the food may be received at the specified temperature.
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Food employee contacting exposed RTE (crab sticks) food with bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Cut leafy greens (70 F) and eggs (60 F) on ice were observed cold holding at improper temperatures. Food was discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment and Utensils/Durability and Strength
Observation: The Oyster blender, Rival crock pot, Emerson microwave are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Food Temperature Measuring Devices
Observation: A temperature measuring device with a suitable small-diameter probe to measure thin masses is not provided and readily accessible to accurately measure the temperature in thin foods.
Correction: A temperature measuring device with a suitable small-diameter probe that is designed to measure the temperature of thin masses shall be provided and readily accessible to accurately measure the temperature in thin foods such as meat patties and fish filets. When determining the temperature of thin foods, those having a thickness less than 13 mm (1/2 inch), it is particularly important to use a temperature sensing probe designed for that purpose. Bimetal, bayonet style thermometers are not suitable for accurately measuring the temperature of thin foods such as hamburger patties because of the large diameter of the probe and inability to accurately sense the temperature at the tip of the probe. However, temperature measurements in thin foods can be accurately determined using a small-diameter probe 1.5 mm (0.059 inch), or less, connected to a device such as thermocouple thermometer.
- Food Temperature Measuring Devices
Observation: A food temperature measuring device is not provided and readily accessible for use in ensuring attainment and maintenance of food temperatures.
Correction: Food temperature measuring devices shall be provided and readily accessible for use in ensuring attainment and maintenance of food temperatures as specified under Chapter 3. The presence and accessibility of food temperature measuring devices is critical to the effective monitoring of food temperatures. Proper use of such devices provides the operator or person in charge with important information with which to determine if temperatures should be adjusted or if foods should be discarded.
- Equipment/Good Repair and Proper Adjustment
Observation: Observed the plate inside ice machine is being held up with rusted screws which do not maintain ice machine in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Observed damaged gaskets on refrigeration units.
Observed the sushi display case damaged and held together with tape.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Warewashing Machine, Cleaning Frequency
Observation: The warewashing machine, compartments of sinks, basins, or other receptacles used for washing and rinsing equipment, utensils, or raw foods, or laundering wiping cloths
Correction: and drainboards or other equipment used to substitute for drainboards as specified under section 4-301.13 are not cleaned before use, at a frequency necessary to prevent recontamination of equipment and utensils and to ensure that the equipment performs its intended function, or at least every 24 hours.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surface of the storage shelving and refrigeration units are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the inside of the ice machine are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. Dish machine is not distributing sanitizer. When tested, no sanitizer observed. Technician came out and repaired machine.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Observed cleaned equipment and utensils were observed stored next handwashing sink is exposed to splash from handwashing.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Handwashing Sink/Using/Operation and Maintenance
Observation: The handwashing sink in the bar area was observed with a drain line from the soda gun holster.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located in the kitchen was observed with a colander of noodles on top and is not accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Outer Openings, Protected (corrected on site)
Observation: The outer openings of the food establishment are not protected against the entry of insects and rodents. Front door propped.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Intensity/Lighting
Observation: The light intensity is below 20 foot candles in toilet rooms.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employees are working with food.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Cleaning, Frequency and Restrictions
Observation: The floors and walls are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Drying Mops
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
- Cleaning of Plumbing Fixtures
Observation: Observed the plumbing fixtures on the handwashing sinks are not clean and/or maintained.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers (spray bottles) used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
07/16/2014 | Routine | |
- Equipment, Food-Contact Surfaces, and Utensils
Observation: All the cutting boards need cleaning.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
|
11/13/2013 | Risk Factor | |
Clean the sushi microwave.
Cool cooked foods uncovered and on flat trays to 41
ºF
within 6 hours.
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Vegetable puffs tightly wrapped were not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Garlic and oil on the counter cold holding at the improper temperature of 81ºF. Discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site)
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in a chemical mechanical operations, using a proper solution. An employee was observed running dishes through the warewashing machine that was not chemically sanitizing. The CFM stated the technician was on the way.
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in chemical manual or mechanical operations, including the application of sanitizing chemicals by immersion, manual swabbing, brushing, or pressure spraying methods, using a solution as specified under section 4-501.114 by providing: (1) An exposure time of at least 10 seconds for a chlorine solution specified under paragraph 4-501.114(A), (2) An exposure time of at least 7 seconds for a chlorine solution of 50 mg/L that has a pH of 10 or less and a temperature of at least 38°C (100°F) or a pH of 8 or less and a temperature of at least 24°C (75°F), (3) An exposure time of at least 30 seconds for other chemical sanitizing solutions, or (4) An exposure time used in relationship with a combination of temperature, concentration, and pH that, when evaluated for efficacy, yields sanitization as defined in Subparagraph 1-201.10(B). Efficacious sanitization depends on warewashing being conducted within certain parameters. Time is a parameter applicable to both chemical and hot water sanitization. The time hot water or chemicals contact utensils or food-contact surfaces must be sufficient to destroy pathogens that may remain on surfaces after cleaning. Other parameters, such as rinse pressure, temperature, and chemical concentration are used in combination with time to achieve sanitization.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: All handwashing sink are not maintained so that it is accessible at all times for employee use. 1. Container observed in basin of the handsink(zen bar). 2. A brilo pad in the basin of the handsink(sushi bar). 3. Ice observed in the handsink basin(kitchen).
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
|
07/15/2013 | Risk Factor | |
**Dog Dining Variance**
#1- Agreed
#2- Agreed
#3- Sign provided during meeting.
#4- Agreed
#5- Owner does not pre-set tables.
#6- Owner will use "to-go" soup cups as single service for dogs.
#7- Agreed
#8- Owner agreed dogs will not be allowed on laps.
#9- Agreed
#10- Sanitizer will be used to clean
#11- Agreed
#12- Agreed
#13- Owner will speak to insurance company. Incident log given to the owner.
#14- Agreed
The Owner agreed to all criterion
**Tentative approval pending
No violation noted during this evaluation. | 04/19/2013 | Other | |
"Keep It Clean" DES Poster handed out.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation (repeated violation)
Observation: Trays of dumplings, prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment and Utensils/Durability and Strength
Observation: The Oster blender, Rival crock pot, Emerson microwave, and the sushi area toaster oven, are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Good Repair and Proper Adjustment
Observation: The door for the sushi display was damaged and observed with tape for repair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surface of the interior bottom of the cabinetry behind the bar is not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Intensity/Lighting
Observation: The light was burned out in the True 2 door uprt.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
|
03/04/2013 | Routine | |
1. The True 1-dr prep ref was still observed missing its handle.
2. Please put a sign on the cooling ice in the bar area directly in front of the handwash sink reminding staff that the ice is for cooling only and not for drinks.
3. The kimchi is made in house by slicing cabbage then mixing it with chili, vinegar, and other spices. The mixture is put in large soy-sauce type containers and then put in the refrigerator where it maintained at 41F or lower. Once the kimchi "tastes sour" (approximately 4 days) it is ready to be served. After discussion with the owner it was agreed that the cabbage would be sliced and served within 7 days like any other refrigerated potentially hazardous food (PHF). If the cabbage is not used within 7 days it will be discarded. This means that no HACCP plan or product assessment is needed.
**Substantial compliance was observed during inspection. The location will return tot he usual inspection schedule. **
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Raw sushi fish was observed over avocados in the right sushi refrigerator.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Critical: Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens (corrected on site) (repeated violation)
Observation: There is no consumer advisory on the a la cart sushi menu. The location has a stamp with the consumer advisory statement and began on the paper menus during inspection.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
|
12/19/2012 | Follow-up | |
Restaurant representatives - add corrected or new information about Asia Bistro, 1301 S Joyce St D-7, Arlington, VA 22202 »