Today's inspection was a follow-up to ensure 3 door glass unit was fully functional. Unit read 38, all temperatures were between 38 F- 41 F. Please ensure when handling ready to eat foods, employees are utilizing gloves. Thank you.
No violation noted during this evaluation. | 10/21/2015 | Follow-up | |
Today's inspection was a follow-up due to a Fact-Finding conference. Substantial compliance observed, however a follow-up will conducted to ensure 3 door glass unit is properly working. Continue with logs, and ensure logs are reflecting all units, especially 3 door glass unit. Follow-up will be next week.
- Equipment/Good Repair and Proper Adjustment
Observation: True" 3 dr prep units on mainline and 3 door glass door are not properly adjusted and/or are in poor repair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
|
10/13/2015 | Follow-up | |
Today's inspection was a follow-up for a risk control plan on cold holding. Substantial compliance not observed, therefore a fact-finding conference will be scheduled and held. Details for conference will be sent/delivered ina letter. Please take temperatures daily, gather invoices, and ensure units are capable of maintaining foods at 41 F or below.
- Time/Temperature Control for Safety Food, Cold Holding (repeated violation)
Observation: Observed several items improperly cold holding in 3 door glass unit. (tomatoes 49 F).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: True" 3 dr prep units on mainline and 3 door glass door are not properly adjusted and/or are in poor repair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
|
09/03/2015 | Follow-up | |
Todays inspection was a follow-up due to an NOV issued. Substantial compliance not observed, however a risk control plan will be created and implemented. Please take temperatures at least every 4 hours and document accordingly. Another follow-up inspection will be on or after 14 days.
- Time/Temperature Control for Safety Food, Cold Holding (repeated violation)
Observation: Observed several items improperly cold holding in 3 door glass unit. (tomatoes 49 F).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
|
08/17/2015 | Follow-up | |
Today's inspection was a follow-up due to repeat priority violations. Substantial compliance not observed, therefore an NOV (Notice of Violation) will be issued. Follow-up inspection will be on or after 30 days (17 August).
- Food Storage Containers, Identified with Common Name of Food (repeated violation)
Observation: Small containers of dry goods are not identified or labeled with the common name of the food.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- Cooling Methods, Food containers (repeated violation)
Observation: Several items in prep units are not cooling properly. Lettuce and items were in tightly covered containers.
Correction: When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (1) Arranged in equipment to provide maximum heat transfer through the container walls
- Time/Temperature Control for Safety Food, Cold Holding (repeated violation)
Observation: Observed several items improperly cold holding in 3 door glass unit. (tomatoes 49 F).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Temperature Measuring Devices (repeated violation)
Observation: Several units are without a temperature measuring device. (3/dr prep units), freezer, 2/dr prep).
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: True" 3/dr prep units on mainline are not properly adjusted and/or are in poor repair. Right unit is 52 F, left is 54 F. 3/dr glass upright unit in kitchen is reading 51 F.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
|
07/16/2015 | Follow-up | |
Please acquire a new CFM card before expiration. Please send an invoice (or documentation) of the service/repair of units. Re-inspection will occur on or after 15 July 15 (10 days).
- Food Storage Containers, Identified with Common Name of Food (repeated violation)
Observation: Small containers of dry goods are not identified or labeled with the common name of the food.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- Cooling Methods, Food containers (corrected on site)
Observation: Improper cooling methods observed. (lids, tightly covered).
Correction: When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (1) Arranged in equipment to provide maximum heat transfer through the container walls
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Observed several foods cold holding at improper temperatures in 3/dr prep (left) and 3/dr prep (right). Corrected by discarding.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Temperature Measuring Devices
Observation: Several units are without a temperature measuring device. (3/dr prep units), freezer, 2/dr prep).
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Sanitizing Solutions, Testing Devices (repeated violation)
Observation: A chlorine test kit or other device that accurately measures the concentration of sanitizing solution is not provided.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Equipment/Fixed, Spacing or Sealing
Observation: Service sink next to dish machine is not sealed to adjoining wall.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: True" 3/dr prep units on mainline are not properly adjusted and/or are in poor repair. Right unit is 52 F, left is 54 F. 3/dr glass upright unit in kitchen is reading 51 F.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: Caulking at hand sinks and 3 compartment sinks are moldy/in need of cleaning.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Observed can opener in need of cleaning.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: Observed handwashing sink used to clean/rinse wiping cloths. Corrected by instruction.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Light Bulbs, Protective Shielding
Observation: Lights above prep units on mainline are not shielded, or shatter resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Poisonous or Toxic Materials/Conditions of Use
Observation: Observed "RAID" bug spray stored in kitchen. Corrected.
Correction: A restricted use pesticide shall be applied only by an applicator certified as defined in 7 USC 136 Definitions, (e) Certified Applicator, of the Federal Insecticide, Fungicide and Rodenticide Act, or a person under the direct supervision of a certified applicator. Because of the toxicity of restricted use pesticides, they can only be applied by certified operators. A certified operator would be aware of the dangers involved in the contamination of food and food-contact surfaces during the application of these materials. Improperly applied pesticides present health risks to employees as well as consumers and special precautions must be taken when restricted use pesticides are applied.
|
07/01/2015 | Routine | |
1. Do not over-fill food containers above fill line.
2. Make sure to properly mark the date on re-packaged salads in the dining room refrigerator.
3. Wash hands frequently.
- Food Storage Containers, Identified with Common Name of Food
Observation: Small containers of wasabi peas, walnuts, pecans, sunflower seeds and granola are not identified with the common name of the food.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Blue cheese (54F), salsa (48F), mozarella (54F), boiled eggs (51F) and all other foods in "True" 3-dr prep refrigerator (right) and grilled chicken breast (46F) in "True" 2-dr prep refrigerator were observed at improper cold holding temperature. The foods were placed on shallow pans and placed uncovered in another cooler for faster cooling.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Sanitizing Solutions, Testing Devices
Observation: A chlorine test kit or other device that accurately measures the concentration of the sanitizing solution is not provided. Instead, the PIC presented quat-ammonia test kit.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Equipment/Good Repair and Proper Adjustment
Observation: True" 3-dr prep refrigerator (right) is not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design. Gaskets of "CDS" 3-dr glass refrigerator are torn.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Handwashing Sink/Using/Operation and Maintenance
Observation: The handwashing station in the back is being used as a dump station. A pipe observed draining in hand sink from dipper well.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Permit to Operate/Responsibilities of Permit Holder
Observation: The 2014 health permit is not posted in a location in the food establishment that is conspicuous to consumers.
Correction: Upon acceptance of the permit issued by the regulatory authority, the permit holder in order to retain the permit shall post the permit in a location in the food establishment that is conspicuous to consumers.
|
06/18/2014 | Routine | |
- Critical: Food Contact with Equipment and Utensils/Preventing Contamination (corrected on site)
Observation: The scoop handle is stored in the drinking ice.
Correction: Food shall only contact surfaces of: (A) Equipment and utensils that are cleaned as specified under Part 4-6 of this Code and sanitized as specified under Part 4-7 of this Code
|
06/10/2013 | Routine | |
All previous violations were corrected, still some of the floor is not smooth and cleanable. License issued.
No violation noted during this evaluation. | 05/14/2013 | Follow-up | |
Still construction debris and equipment on site. None of the cooling units were turn on.
- Temperature Measuring Devices (corrected on site)
Observation: The CDS cooling unit is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Floors, Walls, and Ceilings/Cleanability
Observation: Some of the floor are is not constructed, and installed so that it is smooth and easily cleanable. (Kirsten the Senior inspector took a second look and said the is OK).
Correction: Floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed and installed so that they are smooth and easily cleanable except for anti-slip floor coverings or applications that may be used for safety reasons and except as specified under section 6-201.14. Floors that are of smooth, durable construction and that are nonabsorbent are more easily cleaned. Requirements and restrictions regarding floor coverings, utility lines, and floor/wall junctures are intended to ensure that regular and effective cleaning is possible and that insect and rodent harborage is minimized.
- Handwashing Cleanser, Availability
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap.
- Hand Drying Provision
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Cleaning, Frequency and Restrictions
Observation: All the floors needs cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
05/13/2013 | Pre-Opening | |
Restaurant representatives - add corrected or new information about Sweet Leaf Community Cafe, 2200 Wilson Blvd #103, Arlington, VA 22201 »