Submit 2016 health license renewal application and appropriate fees to the health department located at 2110 Washington Blvd. Suite 350, Arlington VA 22204. The room containing the pizza oven and refrigerated preparation unit is not in use.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The equipment storage shelving near the walk-in refrigerator was observed in need of cleanig. The plastic sticker residue was observed in need of removal from the stainless steel storage table near the kitchen handsink. Exterior of the portable fan located in the kitchen was observed in need of cleaning.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment/Cooking and Baking/Cleaning Frequency (corrected on site)
Observation: The cavity of the microwave was observed in need of cleaning.
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Refuse/Covering Receptacles
Observation: The lid to the outside waste receptacle was observed not properly closed.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered inside the food establishment if the receptacles and units: (1) Contain food residue and are not in continuous use
- Refuse/Maintaining Refuse Areas and Enclosures (repeated violation)
Observation: Outside refuse area observed in need of cleaning.
Correction: A storage area and enclosure for refuse, recyclables, or returnables shall be maintained free of unnecessary items, as specified under section 6-501.114, and clean. Proper storage and disposal of garbage and refuse are necessary to minimize the development of odors, prevent such waste from becoming an attractant and harborage or breeding place for insects and rodents, and prevent the soiling of food preparation and food service areas. Improperly handled garbage creates nuisance conditions, makes housekeeping difficult, and may be a possible source of contamination of food, equipment, and utensils.
- Floor and Wall Junctures, Coved, Enclosed or Sealed
Observation: The floor and wall juncture cove base underneath the 3-compartment sink and around the mop sink area was observed in need of repair.
Correction: In food establishments in which cleaning methods other than water flushing are used for cleaning floors, the floor and wall junctures shall be coved and closed to no larger than 1 mm (one thirty-second inch). When cleaning is accomplished by spraying or flushing, coving and sealing of the floor/wall junctures is required to provide a surface that is conducive to water flushing.
- Controlling Pests
Observation: Several fruit flies observed in the hookah preparation area.
Correction: The premises shall be maintained free of insects, rodents, and other pests. The presence of insects, rodents, and other pests shall be controlled to eliminate their presence on the premises by eliminating harborage conditions.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: Floor surfaces under/behind equipment, in the walk-in refrigerator and in the rest-rooms were observed in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: Cook-line vent filters observed in need of cleaning.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
- Licenses for Food Establishments
Observation: The food establishment does not have a valid license. The health license has expired and needs to be renewed.
Correction: No person shall operate a food establishment who does not have a valid license issued to him by the county manager. Only a person who complies with the requirements of this chapter shall be entitled to receive or retain such a license. Licenses are not transferable.
|
01/20/2016 | Routine | |
Cutting boards observed scratched, scoured, and in need of replacement. Wiping cloths observed not properly held in chemical sanitizer between use. The kitchen hood vents were observed in need of cleaning. Mold around the 3-compartment sink observed in need of cleaning. An oven and a refrigerated preparation unit were observed in the process of being installed in the facility. Prior to kitchen renovations, proper plans must be submitted to the health department for review and approval. According to the manager on duty, the owner was currently out of the area and will return within a few weeks to potentially finish the equipment installation. The manager will notify the owner to contact the health department to discuss.
- Cleaning of Plumbing Fixtures
Observation: Kitchen handsink observed in need of cleaning.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
|
07/21/2015 | Risk Factor | |
Correct observations. The hookah lounge section was observed being painted/renovated. According to the manager, there was no construction to be done in the kitchen area.
- Food Storage Containers, Identified with Common Name of Food
Observation: Several dry ingredient storage containers observed not properly labeled.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The bare wood shelving near the kitchen handsink was observed in need of painting.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Sanitizing Solutions, Testing Devices
Observation: Quaternary ammonium test strips were not observed available for measuring the sanitizer concentration.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Cutting Surfaces (repeated violation)
Observation: Cutting board(s) observed scratched and scoured.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment and Utensils, Air-Drying Required
Observation: Clean and sanitized utensils/equipment observed not properly air dried and stacked while wet.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Refuse/Maintaining Refuse Areas and Enclosures
Observation: Outside refuse area observed in need of cleaning.
Correction: A storage area and enclosure for refuse, recyclables, or returnables shall be maintained free of unnecessary items, as specified under section 6-501.114, and clean. Proper storage and disposal of garbage and refuse are necessary to minimize the development of odors, prevent such waste from becoming an attractant and harborage or breeding place for insects and rodents, and prevent the soiling of food preparation and food service areas. Improperly handled garbage creates nuisance conditions, makes housekeeping difficult, and may be a possible source of contamination of food, equipment, and utensils.
- Light Bulbs, Protective Shielding
Observation: Lights in the kitchen observed not properly shielded.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Dressing Rooms and Lockers/Using (corrected on site)
Observation: Employee jacket observed improperly stored on the meat grinder that was not in use at the time.
Correction: Lockers or other suitable facilities shall be used for the orderly storage of employee clothing and other possessions. Street clothing and personal belongings can contaminate food, food equipment, and food preparation surfaces and consequently must be stored in properly designated areas or rooms.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Chemical spray bottle of cleaning product observed not properly labeled.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Poisonous or Toxic Materials/Separation/Spacing or Partitioning (corrected on site)
Observation: Chemical spray bottle of cleaning product observed improperly stored on a shelf above the food preparation area.
Correction: Poisonous or toxic materials shall be stored so they can not contaminate food, equipment, utensils, linens or single-service and single-use articles by locating the poisonous or toxic materials in an area that is not above food, equipment, utensils, linens, and single-service or single-use articles. This paragraph does not apply to equipment and utensil cleaners and sanitizers that are stored in warewashing areas for availability and convenience if the materials are stored to prevent contamination of food, equipment, utensils, linens, and single-service and single-use articles. For example, the storage of these types of materials directly above or adjacent to food could result in contamination of the food from spillage.
|
01/27/2015 | Routine | |
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention
Observation: An open beverage container and/or a closed beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Hair Restraints/Effectiveness
Observation: Food employees are not wearing effective hair restraints.
Correction: Food employees shall wear hair restraints such as hats, hair coverings or nets, beard restraints, and clothing that covers body hair, that are designed and worn to effectively keep their hair from contacting exposed food
- Manual Warewashing/Sink Compartment Requirements (repeated violation)
Observation: The 3-part sink is missing the water faucet and two stoppers.
Correction: Except as specified in paragraph (C) of this section, a sink with at least 3 compartments shall be provided for manually washing, rinsing, and sanitizing equipment and utensils. The 3 compartment sink requirement allows for proper execution of the 3-step manual warewashing procedure. If properly used, the 3 compartments reduce the chance of contaminating the sanitizing water and therefore diluting the strength and efficacy of the chemical sanitizer that may be used. Alternative manual warewashing equipment, allowed under certain circumstances and conditions, must provide for accomplishment of the same 3 steps: 1. Application of cleaners and the removal of soil
- Equipment/Good Repair and Proper Adjustment
Observation: The Walk-in cooling unit shelves are rusty.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces (repeated violation)
Observation: The surfaces of the cutting boards are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The 3-part sink and the mop sink is moldy at the wall junctures. The nonfood contact surfaces of the electric saw need cleaning. The Men's room vent is heavily dusty.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Physical Facilities/Repairing (repeated violation)
Observation: The kitchen floor tiles are in poor repair. The walk-in cooling unit base board is in poor repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions
Observation: The entire kitchen floor needs cleaning especially corners and edges. The kitchen walls need cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Drying Mops
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
|
05/23/2014 | Routine | |
1. Ice machine not in operation.
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface of the cloth under the cutting board is not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Manual Warewashing/Sink Compartment Requirements (repeated violation)
Observation: The 3 compartment sink is missing a faucet to easily fill each basin
Correction: and missing two properly fitting stoppers to provide manual washing, rinsing, and sanitizing equipment and utensils.
- Cutting Surfaces
Observation: The surfaces of the cutting board are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surface areas of the meat saw is not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Refuse/Covering Receptacles (repeated violation)
Observation: Shared strip mall trash receptacles are not kept covered with tight-fitting lids or doors.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
- Physical Facilities/Repairing
Observation: The men's rest-room ceiling/wall is not maintained in good repair. There are a few wall, ceiling, and floor tiles in the kitchen that are damaged. There are some holes in the walls of the kitchen to the right of the walk-in refrigerator. The food dry storage walls junctures are no longer properly sealed to each other, their ceiling, and floor.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests
Observation: Insect, rodent, and/or other pest harborage conditions exist on the premises. Knats observed in the hooka/drink prep area. Fruit flies and mouse droppings were observed in the dry food storage room.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
|
04/26/2013 | Routine | |
Restaurant representatives - add corrected or new information about Shisha Palace, 2325 S Eads St, Arlington, VA 22202 »