- Equipment/Fixed, Spacing or Sealing
Observation: The 3-part sink is loose from the wall.
Correction: Counter-mounted equipment that is not easily movable shall be installed to allow cleaning of the equipment and areas underneath and around the equipment by being: (1) Sealed
- Equipment/Good Repair and Proper Adjustment
Observation: The gasket of the small freezer by the grill is damaged.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces (repeated violation)
Observation: The surfaces of one cutting board has too many cuts.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment Food-Contact Surfaces and Utensils/Cleaning Frequency (Critical)
Observation: Two cutting boards were moldy.
Correction: Equipment food-contact surfaces and utensils shall be cleaned: (1) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The 3-part sink caulking is moldy.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Physical Facilities/Repairing (repeated violation)
Observation: The wall by the dishwashing machine has a lots of holes from previous equipment. The entire kitchen floor is damaged is not smooth and cleanable. The walk-in freezer floor is damaged.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Sanitizers, Criteria/Chemicals for Food Contact Surfaces
Observation: The quaternary sanitizer was more than 600 ppm at the 3-part sink.
Correction: Chemical sanitizers and other chemical antimicrobials applied to food-contact surfaces shall meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions). Chemical sanitizers are included with poisonous or toxic materials because they may be toxic if not used in accordance with requirements listed in the Code of Federal Regulations (CFR). Large concentrations of sanitizer in excess of the CFR requirements can be harmful because residues of the materials remain. The CFR reference that is provided lists concentrations of sanitizers that are considered safe.
|
01/20/2016 | Routine | |
| No violation noted during this evaluation. | 09/25/2015 | Risk Factor | |
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Melted cheese at 47 F inside the walk-in cooler.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Sanitizers, Criteria/Chemicals for Food Contact Surfaces (corrected on site)
Observation: The quaternary sanitizer at the 3 part sink was more than 600 ppm.
Correction: Chemical sanitizers and other chemical antimicrobials applied to food-contact surfaces shall meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions). Chemical sanitizers are included with poisonous or toxic materials because they may be toxic if not used in accordance with requirements listed in the Code of Federal Regulations (CFR). Large concentrations of sanitizer in excess of the CFR requirements can be harmful because residues of the materials remain. The CFR reference that is provided lists concentrations of sanitizers that are considered safe.
|
05/08/2015 | Risk Factor | |
- Hands and Arms/When to Wash
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Contamination from Hands/Preventing Contamination by Employees
Observation: Food employee contacting ready to eat food with bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Cooling, Cooked Food (corrected on site) (repeated violation)
Observation: Pasta was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
- Cutting Surfaces (repeated violation)
Observation: The surfaces of the small cutting board by the ribs grill is no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site) (repeated violation)
Observation: Dishwashing machine is not ejecting sanitizer.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Equipment and Utensils, Air-Drying Required (repeated violation)
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with (food containers observed stacked while still wet).
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
|
02/18/2015 | Routine | |
Garden outside by outside dining area.
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Ribs were not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less. The manager was informed about proper cooling methods and proper time/temperature requirements.
- Cooling Methods (corrected on site)
Observation: Methods used for cooling red beans and rice in a large deep plastic container in the walk-in refrigerator at 188 F can not be accomplished with the time and temperature criteria.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Cooling Methods, Food containers
Observation: Ribs tightly wrapped and stacked on top of one another were not arranged to provide maximum heat transfer while cooling.
Correction: When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (1) Arranged in equipment to provide maximum heat transfer through the container walls
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Ribs and chicken hot holding at the improper temperature of 130 F inside the Alto Sham. The Alto Sham was adjusted to a hotter temperature.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Fruit salad and potato salad in the prep refrigerator and ribs in the walk-in refrigerator were cold holding at the improper temperature of 43-45 F. The prep refrigerator was adjusted to a colder setting.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surfaces of the cardboard on the shelves with the packaged sauces are not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Temperature Measuring Devices, Ambient Air and Water
Observation: The ambient air temperature measuring device located in the Alto Sham is not accurate.
Correction: Provide a temperature measuring device that is easily readable and accurate to +/-1.5 degrees Celsius in the intended range of use.
- Equipment, Food-Contact Surfaces, and Utensils
Observation: Some stacked cutting boards, the food processor and some attachments are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: The ice tea dispenser nozzles and inside the ice machine are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning in the kitchen dishmachine. No chlorine sanitizer detected on equipment after cycle. Do not use the unit until 50-100 ppm is detected, use the three compartment sink.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Equipment and Utensils, Air-Drying Required
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food (food containers observed stacked while still wet).
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Outer Openings, Protected
Observation: The outer openings of the food establishment are not protected against the entry of insects and rodents (air gaps observed around the exterior doors).
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food (couple hood lights out and several shields are dirty).
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing
Observation: The kitchen floors are not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests (Critical)
Observation: Proper pest control methods are not used to minimize the presence of insects, rodents, and other pests found in the establishment (numerous flies were observed in the facility). Rat burrows were observed in the ground behind the dumpsters at the fence. Some wood stored outside on the ground. The cardboard dumpster is full.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by using methods, if pests are found, such as trapping devices or other means of pest control as specified under sections 7-202.12, 7-206.12, and 7-206.13. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Cleaning, Frequency and Restrictions
Observation: The floors throughout the kitchen and the walls by the dish machine are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Drying Mops
Observation: After use, the mops are not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
- Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material (spray bottles).
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Permit to Operate/Responsibilities of Permit Holder
Observation: The permit is not posted in a location in the food establishment that is conspicuous to consumers [at bar facing away from customers].
Correction: Upon acceptance of the permit issued by the regulatory authority, the permit holder in order to retain the permit shall post the permit in a location in the food establishment that is conspicuous to consumers.
- Permit to Operate/Responsibilities of Permit Holder
Observation: The permit holder is not complying with the provisions of this Code, granted variance, and/or approved plans [Doggie dining variance is not posted conspicuously to the public, missing dog friendly signs at the picnic tables, and a reusable dog water bowl was observed outside].
Correction: Upon acceptance of the permit issued by the regulatory authority, the permit holder in order to retain the permit shall comply with the provisions of this Code including the conditions of a granted variance as specified under section 8-103.12, and approved plans as specified under section 8-201.12..
- Permit to Operate/Responsibilities of Permit Holder
Observation: The permit holder is not complying with directives of the regulatory authority [Outside storage shed is for wood only
Correction: single service items were observed inside the unit].
|
07/03/2014 | Routine | |
No doggie dining observed at time of inspection.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency (corrected on site)
Observation: Surfaces of the soda gun nozzle at the bar, observed with mold build-up, are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink next to ice maker is used for purposes other than handwashing. Hand sink observed being used to fill a water pitcher.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Handwashing Cleanser, Availability (corrected on site)
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink. No hand soap at bar hand sink.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
|
11/25/2013 | Risk Factor | |
- Critical: Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An employee was eating in the kitchen in an area where contamination of exposed food or clean equipment may occur.
Correction: An employee shall eat, drink, or use any form of tobacco only in designated areas where the contamination of exposed food
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site)
Observation: Observed baby back ribs (120 F to 125 F) and pork ribs (117 F to 119 F) hot holding at improper temperatures in the Alto Sham hot holding unit. Thermometer on unit reading 200 F. Temperature control set at 200 F. Food was reheated immediately.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency (corrected on site)
Observation: Surfaces of the tea urn dispensers are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
|
07/11/2013 | Risk Factor | |
**Dog Dining Variance**
1) Agree
2) Agree
3) Sign provided during the meeting.
4) Agree
5) The owner does not pre-set.
6) The owner will use "to-go" containers for dogs.
7) Agree
8) Agree. The owner agree dogs will not be allowed on laps.
9) Agree
10) The owner uses a sanitizer spray to clean the outdoor area.
11) Agree
12) Agree
13) Incident log given to the owner.
14) Agree
Approval pending
-Do not start dog dining until variances are obtained.
No violation noted during this evaluation. | 05/15/2013 | Other | |
- Cutting Surfaces
Observation: The surfaces of all the cutting boards are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: Both 3-part sink are moldy at the wall juncture.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Equipment and Utensils, Air-Drying Required
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food, one light out under the hood.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing (repeated violation)
Observation: The entire floor is in poor repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions
Observation: The WIC floor needs cleaning, blood stains.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Drying Mops
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
|
03/14/2013 | Routine | |
Restaurant representatives - add corrected or new information about Rocklands Barbeque And Grilling Company, 3471 Washington Blvd, Arlington, VA 22201 »