- Eating, Drinking, or Using Tobacco/Food Contamination Prevention
Observation: Observed employee eating in an area other than designated break area while preparing/handling food or contacting clean food contact surfaces.
Correction: All employees who are eating must be in the designated break area away from food preparation/handling areas to prevent cross contamination.
- Wiping Cloths, Use Limitation
Observation: Dry wiping cloths and/or chemical sanitizing solutions are not kept free of food debris and/or visible soil.
Correction: Dry wiping cloths and the chemical sanitizing solutions in which wet wiping cloths are held between uses shall be free of food debris and visible soil. Soiled wiping cloths, can become breeding grounds for pathogens that could be transferred to food. The sanitizing solution must be changed as needed to minimize the accumulation of organic material and sustain proper concentration.
- Wiping Cloths, Use Limitation
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration
Correction: and/or not laundered daily.
- Food Storage/Preventing Contamination from the Premises (repeated violation)
Observation: Observed food stored on the floor in the freezer.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Cooling, Ambient Ingredients (corrected on site)
Observation: Tuna prepared from ingredients at ambient temperature was not cooled within 4 hours to 5ºC (41ºF). Food was relocated to walk-in cooler to cool.
Correction: Time/temperature control for safety food shall be cooled within 4 hours to 5ºC (41ºF) or less, if prepared from ingredients at ambient temperature, such as reconstituted foods and canned tuna. Safe cooling requires removing heat from food quickly enough to prevent microbial growth. Excessive time for cooling of time/temperature control for safety foods has been consistently identified as one of the leading contributing factors to foodborne illness. During slow cooling, time/temperature control for safety foods are subject to growth of a variety of pathogenic microorganisms. If the food is not cooled in accordance with this Code requirement, pathogens may grow to sufficient numbers to cause foodborne illness.
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site) (repeated violation)
Observation: Sauces prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Nonfood-Contact Surfaces/Nonabsorbent (repeated violation)
Observation: The nonfood-contact surfaces of the shelving in the walk-in cooler are not corrosion-resistant, nonabsorbent, and/or smooth (rusted).
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Food Temperature Measuring Devices
Observation: A food temperature measuring device is not provided and readily accessible for use in ensuring attainment and maintenance of food temperatures.
Correction: Food temperature measuring devices shall be provided and readily accessible for use in ensuring attainment and maintenance of food temperatures as specified under Chapter 3. The presence and accessibility of food temperature measuring devices is critical to the effective monitoring of food temperatures. Proper use of such devices provides the operator or person in charge with important information with which to determine if temperatures should be adjusted or if foods should be discarded.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surfaces of the refrigerators, door gaskets and shelving in the walk-in cooler are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: Observed equipment food-contact surfaces and utensils stored as clean are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Observed employee cleaning food contact surfaces and not sanitizing after cleaning.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Maintaining Premises, Unnecessary Items and Litter
Observation: The premises is not free of items that are unnecessary to the operation or maintenance of the establishment (unused refrigeration equipment).
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors and walls under and behind equipment are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/30/2016 | Routine | |
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention
Observation: Observed employee drinking from an uncovered container in the food preparation area. Corrected by instruction.
Correction: Employees may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands (2) The container and (3) Exposed food clean equipment, utensils, and linens and unwrapped single-service and single-use articles.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The food-contact surfaces of food-contact surfaces and utensils stored as clean are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the ice scoop holder, inside ice machine and tea urns and dispensers are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. Observed an employee cleaning utensils in a one compartment food prep sink not accomplishing the proper steps of warewashing including sanitizing after cleaning.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink located closest to the cookline in the kitchen is not maintained so that it is accessible at all times for employee use (blocked by cart).
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Cleaning of Plumbing Fixtures
Observation: Handwashing sinks are not clean and/or maintained.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
|
11/24/2015 | Risk Factor | |
All prepared foods must be cooled (on ice, freezer or walk-in refrigerator) before placing in cold holding units.
Observed faucet leaking on three compartment sink.
Observed floors under and behind equipment in need of cleaning.
All utensils and food contact surfaces must be air dried before storing.
- Hands and Arms/Where to Wash (corrected on site)
Observation: A food employee was observed cleaning their hands in a food preparation sink. Corrected by instruction.
Correction: Food employees shall clean their hands in a handwashing sink or approved automatic handwashing facility and may not clean their hands in a sink used for food preparation or warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste.
- Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Food employee contacting exposed RTE food (chicken salad) with bare hands. Corrected by instruction.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Observed foods (eggs, rice, potatoes, pork and fish) on the buffet hot holding at improper temperatures. Foods that had been on the buffet for breakfast were discarded. Foods that were just prepared will be on the buffet from 11:00 AM until 2:00 PM. Recommend using Time As A Public Health Control for foods on the hot buffet.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Observed cheeses (sliced and shredded) cold holding at the improper temperature of 60 F to 62 F in the M3 two door prep unit. Food was discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The food-contact surfaces of multiuse utensils stored as clean were not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. Observed employees cleaning food containers in the prep sink then placing them on shelf to store with no sanitizer step included.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers (spray bottles) used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
08/11/2015 | Risk Factor | |
- Safe, Unadulterated, and Honestly Presented/Condition (corrected on site)
Observation: Observed food and food containers in the walk-in cooler with mold and is not safe and/or unadulterated. Food was discarded.
Correction: Food shall be safe, unadulterated, and, as specified under section 3-601.12, honestly presented.
- Food Storage/Preventing Contamination from the Premises (repeated violation)
Observation: Observed lettuce on utensil drying rack under utensils which were air drying and dripping water.
Observed employee washing sanitizer bucket next to lettuce on a prep sink.
Correction: Store food where it is not exposed to splash, dust, or other contamination and/or install an approved, durable and cleanable barrier between the splash source and the food to prevent contamination.
- Thawing (corrected on site)
Observation: Turkey not thawed properly. Observed turkey being thawed on a shelf in the kitchen.
Correction: Time/temperature control for safety food shall be thawed: (A) Under refrigeration that maintains the food temperature at 5ºC (41ºF) or less
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site) (repeated violation)
Observation: Sauces prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded. Corrected by instruction.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The one door prep unit and the two door prep unit are not functioning.
The front panel on the ice machine is missing.
The Delfield 2 door refrigerator is dripping water inside.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surface of the equipment in the kitchen an=d the shelving in the walk-in cooler are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: Observed colanders, utensils and food containers not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment and Utensils, Air-Drying Required (repeated violation)
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried or adequately drained before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Controlling Pests (Critical)
Observation: Observed mice droppings throughout the kitchen under and behind equipment (on floor).
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by using methods, if pests are found, such as trapping devices or other means of pest control as specified under sections 7-202.12, 7-206.12, and 7-206.13. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Cleaning, Frequency and Restrictions
Observation: Observed the floors and walls under and behind equipment are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/24/2015 | Routine | |
Exterior of the paper towel dispenser in need of cleaning. HVAC vents in ceiling observed rusted. Shelving in the walk-in refrigerator observed rusted. Wiping cloths observed not properly stored in chemical sanitizer between uses. Remove any non-functioning equipment. The floor surface under/around cook-line and kitchen equipment in need of cleaning. Roach observed on the wall next to the non-functioning 2-door reach in unit. Cut melons prepared the morning observed at 52 F - 54 F, product was just placed on the cold bar and submerged in ice. Ensure that TCS product prepared from pre-chilled ingredients and/or ambient air ingredients properly cool down to 41 F within 4 hours from start of preparation.
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Employee observed handling ready-to-eat sliced tomatoes with his/her bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Critical: Food Contact with Equipment and Utensils/Preventing Contamination (corrected on site)
Observation: Employee observed cracking raw shell eggs at the cook-line, then improperly handling a ready-to-eat bagel.
Correction: Food shall only contact surfaces of: (A) Equipment and utensils that are cleaned as specified under Part 4-6 of this Code and sanitized as specified under Part 4-7 of this Code
- Critical: Time/Temperature Control for Safety Food, Cold Holding, Eggs (corrected on site)
Observation: Container of raw shell eggs observed improperly stored at room temperature along the cook-line (product was placed under refrigeration by person in charge).
Correction: Eggs that have not been treated to destroy all viable Salmonellae shall be stored in refrigerated equipment that maintains an ambient air temperature of 7ºC (45ºF) or less.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The can opener blade and the kitchen preparation tables were observed in need of cleaning and sanitizing.
Correction: Properly clean and sanitize food equipment.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: The bulk ice machine chute was observed in need of cleaning and sanitizing.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Employee observed washing dishes at the 3-comparment sink without the sanitizer basin correctly set-up.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: Utensils observed improperly stored in the cook-line handsink.
Correction: The handwashing facility identified above is to be used for washing hands only.
|
11/21/2014 | Risk Factor | |
Fly strip in the ceiling above the mop sink needs changing. Remember to cool products in shallow pans and use an ice bath for faster cooling. Remove the cardboard from the floor in the walk-in refrigerator and along the cook-line. According to the manager the product on the salad bar is prepared every day and set-up around 10:30 am. The product needs is placed on the salad bar in an ice bath but must be monitored to ensure that the product cools from ambient air temperature to 41 F within 4 hours. If product does not cool from ambient air temperature to 41 F in 4 hours then it must be discarded. Chlorine sanitizer in the 3-compartment sink checked for proper concentration using the provided test strips. The gasket to the 2-door Delfield refrigerator was observed not tightly closing.
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Pan of tilapia on the buffet bar observed hot holding at the improper temperature (128 F). Product was reheated by the person in charge.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Bulk ice machine chute observed in need of cleaning.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Utensils observed improperly cleaned in the front prep sink and not properly sanitized (utensils & equipment are to be properly washed, rinsed, and sanitized in the 3-compartment sink).
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
|
07/25/2014 | Risk Factor Assessment | |
- Nonfood-Contact Surfaces/Nonabsorbent (repeated violation)
Observation: The nonfood-contact surfaces of the shelving in the walk-in cooler which are rusted are not corrosion-resistant, nonabsorbent, and/or smooth. The wiping cloths used under cutting boards is not made of nonabsorbent material.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surfaces of the equipment in the kitchen (grill at front cookline, unused refrigerators, shelving in the walk-in cooler) are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment and Utensils, Air-Drying Required (repeated violation)
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Controlling Pests
Observation: Insect, rodent, and/or other pest harborage conditions exist on the premises. Observed dead roaches in unused refrigerator and in kitchen.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Maintaining Premises, Unnecessary Items and Litter
Observation: The premises is not free of items (nonfunctional equipment) that are unnecessary to the operation or maintenance of the establishment.
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
- Cleaning, Frequency and Restrictions
Observation: The floors and walls under and behind equipment are not cleaned as often as necessary to keep them clean. Ceiling tiles need cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
04/21/2014 | Follow-up | |
Post 2014 License
Clean floors, walls, and ceilings where needed.
Clean entire walk-in unit.
Repair faucet at 3 compartment food prep sink.
Establishment issued a Notice of Violation (NOV) for pattern of violations.
- Critical: Hands and Arms/When to Wash
Observation: A food employee failed to wash his or her hands during food preparation when changing tasks. Corrected by instruction.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Food Storage/Preventing Contamination from the Premises
Observation: Observed food stored on floor in freezer.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Cooling Methods
Observation: Observed cooked potatoes that were placed in walk-in tightly covered.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Observed foods cold holding at the improper temperatures in the 2 door prep unit. Observed temperature of unit at 51 F. All potentially hazardous foods were discarded. Observed foods that had been taken out of walk-in cooler for reheating and were holding at 58 to 60 F (eggs, chicken, pasta, rice). Foods were discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Foods prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- RTE, TCS, Date Marking/Commercially Processed Food
Observation: Deli meats and cheeses prepared and packaged by a food processing plant opened and held for more than 24 hours were not clearly marked at the time the original container was opened in the food establishment to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature and time combination specified in paragraph (A) of this section and: (1) The day the original container is opened in the food establishment shall be counted as Day 1
- Nonfood-Contact Surfaces/Nonabsorbent (repeated violation)
Observation: The nonfood-contact surfaces of the shelving in the walk-in cooler which are rusted are not corrosion-resistant, nonabsorbent, and/or smooth. The cardboard lining the shelving is not made of nonabsorbent material.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Food-Contact Surfaces/Cleanability
Observation: The food-contact surfaces of the colanders and plastic containers are not smooth, free of breaks, open seams, cracks, chips, inclusions, pits, similar imperfections, finished to have smooth welds and joints, and/or accessible for cleaning and inspection by an approved method.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Temperature Measuring Devices
Observation: Several refrigerators are not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The 1 door prep unit and the 2 door prep unit are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design. The units are not maintaining an ambient air temperature of 41 F and below.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surfaces of the equipment in the kitchen are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: Observed various multi-use items stored as clean were not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment and Utensils, Air-Drying Required
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Single-service cups are improperly stored unprotected.
Correction: Single-service and single-use articles shall be stored as specified under section (A) of this section and shall be kept in the original protective package or stored by using other means that afford protection until used. Clean equipment and multiuse utensils which have been cleaned and sanitized, laundered linens, and single-service and single-use articles can become contaminated before their intended use in a variety of ways such as through water leakage, pest infestation, or other insanitary condition.
- Hand Drying Provision (corrected on site)
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Critical: Food Manager Certificate and Responsibility
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
03/21/2014 | Routine | |
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site)
Observation: Fried chicken at 120 F, fried rice at 115 F and beef with vegetables a 115 F, all the foods were discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Steamed kale at 45 F, cut melon and fruits at 45 and 46 F, all foods were discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
|
11/20/2013 | Risk Factor | |
1. The establishment has improved a lot since last inspection, therefore, NOV is removed and the facility may return to normal business.
2. Please make sure to coll all cooked/prepared foods 41F or below before placing on cold salad bar.
3. Place one or two additional thermometers in walk-in refrigerators and take food temperatures couple of times to ensure it is working OK.
4. Correct other good retail practices observations which are out compliance as soon as possible.
5. Make sure to renew your NoVA CFM-License as it is expiring on 06/24/2012.
- Cooling Methods (corrected on site) (repeated violation)
Observation: Methods used for cooling boiled potatoes can not be accomplished with the time and temperature criteria.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: The following foods were observed at improper cold holding temperature:
1. Sting beans (52F), Steamed kale (57F), California rolls (47F).
2. Ham (43F), Pulled pork (43F), Corned beef hash (48F) and Sausage links (43F) in the walk-in refrigerator - the thermostat was lowered to 38F.
Correction: (CORRECTED DURING INSPECTION) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Nonfood-Contact Surfaces/Nonabsorbent (repeated violation)
Observation: The nonfood-contact surface of the rusty walk-in shelves and carboard used as liner on shelves is not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment/Good Repair and Proper Adjustment (corrected on site) (repeated violation)
Observation: The "Tafco" walk-in refrigerator (thermostat lowered to 38F), "Delfield" 2-doors upright refrigerator and freezer (not in use) are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Light Bulbs, Protective Shielding (repeated violation)
Observation: The light bulbs in the open display case are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
|
06/10/2013 | Follow-up | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Raw meat stored next to an open container of milk and over produce in walk-in refrigerator.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- In-Use Utensils, Between-Use Storage (repeated violation)
Observation: Knives are improperly stored in between work tables.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Cooling Methods (corrected on site)
Observation: Methods used for cooling boiled potatoes and noodles can not be accomplished with the time and temperature criteria.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Critical: Potentially Hazardous Food, Hot Holding (repeated violation)
Observation: The following foods were observed at improper hot holding temperature on steamtable:
Fried okra (99F), Fried rice (123F), Salt-pepper chicken (118F), Fried chicken (103-120F), Roasted chicken, and Beef with broccoli (133F),
Correction: (discarded) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: The following foods were observed at improper cold holding temperature:
1. Boiled eggs (57F), Cottage cheese (57F), Greek salad (59F), Sting beans (67F), Steamed kale (69F), California rolls (67F), Cut melons (60F), Bean salad (63F), Tuna salad (63F), Imitation crab salad (65F) and cut lettuce (48F) on cold salad bar - (all the foods were discarded).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens (repeated violation)
Observation: The food establishment serves or sells raw or undercooked food and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Nonfood-Contact Surfaces/Nonabsorbent (repeated violation)
Observation: The nonfood-contact surface of the rusty walk-in shelves and carboard used as liner on shelves is not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The "Tafco" walk-in refrigerator, "Delfield" 2-doors upright refrigerator and freezer are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Light Bulbs, Protective Shielding (repeated violation)
Observation: The light bulbs in the open display case are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Hand Drying Provision (corrected on site)
Observation: No paper towels on front handwashing sink.
Correction: Each handwashing sink or group of adjacent handwashing sinks shall be provided with: (A) Individual, disposable towels
|
06/03/2013 | Routine | |
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Food preparation and dispensing utensils are improperly stored [some bowls instead of scoops were found in some bulk food bins.]
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site)
Observation: Fried eggs and scrambled eggs doubled panned in the buffet were hot holding at the improper temperatures of 95-118ºF.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Milk in pitchers for coffee cold holding at the improper temperature of 52-56ºF.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: The food establishment serves undercooked eggs (fried eggs) at the hot buffet bar and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder by the product.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface of the cardboard lined shelves are not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment/Good Repair and Proper Adjustment
Observation: The ice machine is missing its cover panel
Correction: the "Delfield" upright 2-door refrigerator and freezer are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (corrected on site)
Observation: The can opener and a knife on the magnetic strip were not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning [3-compartment sink not set up properly to wash-rinse-sanitize & air dry in that order.]
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Plumbing System/Maintained in Good Repair
Observation: There is a leak under the warewashing 3-part sink left drain pipe.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Light Bulbs, Protective Shielding
Observation: One set of light bulbs in the kitchen ceiling are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Physical Facilities/Repairing
Observation: The wall corner trims in the kitchen, and a baseboard tile by the rear door are not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests
Observation: Insect, rodent, and/or other pest harborage conditions exist on the premises [Dead German cockroaches were observed in the cabinetry under the soda fountain machine.]
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Critical: Food Manager Certificate and Responsibility (repeated violation)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager [Fax me a copy of your new card including the number and expiration date within 10 days or a follow-up inspection will occur thereafter.]
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
03/26/2013 | Routine | |
Restaurant representatives - add corrected or new information about Plaza Gourmet, 2173-B Crystal Plaza Arcade, Arlington, VA 22202 »