- Hair Restraints/Effectiveness
Observation: Food employees are not wearing effective hair restraints.
Correction: Food employees shall wear hair restraints such as hats, hair coverings or nets, beard restraints, and clothing that covers body hair, that are designed and worn to effectively keep their hair from contacting exposed food
- Wiping Cloths, Use Limitation
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration
Correction: and/or not laundered daily.
- Temperature Measuring Devices
Observation: The large pizza prep table is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The pizza prep table door gaskets are damaged.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: The pizza oven conveyor screen is heavily soiled and accumulation of food debris.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The inside of the Beverage-Air and Fricon freezers need cleaning.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 10 foot candles in the walk-in cooling unit.
Correction: The light intensity shall be at least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in the walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning. Properly distributed light makes the need for cleaning apparent by making accumulations of soil conspicuous.
- Cleaning, Frequency and Restrictions
Observation: All the floor corners and edges need cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Drying Mops (repeated violation)
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
|
02/03/2016 | Routine | |
Sweet flies observed in the back room. Please obtain the CFM card from ORS Interactive and send me a copy by text to my working phone.
- Poisonous or Toxic Materials/Restrictions/Presence and Use (corrected on site)
Observation: A can of RAID was found at the back food prep room.
Correction: Only those poisonous or toxic materials that are required for the operation and maintenance of the establishment, such as for the cleaning and sanitizing of equipment and utensils and the control of insects and rodents, shall be allowed in the food establishment. This section does not apply to packaged poisonous or toxic materials that are for retail sale. The presence in the establishment of poisonous or toxic materials that are not required for the maintenance and operation of the establishment represents an unnecessary risk to both employees and consumers. Preserving food safety depends in part on the appropriate and proper storage and use of poisonous or toxic materials that are necessary to the maintenance and operation of a food establishment. Even those that are necessary can pose a hazard if they are used in a manner that contradicts the intended use of the material as described by the manufacturer on the material's label. If additional poisonous or toxic materials are present, there is an unwarranted increased potential for contamination due to improper storage (e.g., overhead spillage that could result in the contamination of food, food-contact surfaces, or food equipment) or inappropriate application.
- Food Manager Certificate and Responsibility
Observation: No certified food manager on duty at the time of the inspection.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
08/31/2015 | Risk Factor | |
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Marinated sauce at 51 F and meat balls at 115 F, discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
|
03/27/2015 | Risk Factor | |
- Equipment/Fixed, Spacing or Sealing
Observation: The hand sink by the pizza oven is loose from the wall.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The prep table door gaskets are in poor repair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The water heater is damaged a the bottom.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The walk-in cooling unit shelves are rusty.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces
Observation: The surfaces of the prep table cutting board has to many cuts and are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The walk-in sprinkler nozzle is dusty.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The pizza oven hood is dusty.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The door gaskets of the upright freezer are dirty.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 20 foot candles inside the glass cooling unit, the light is out.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 10 foot candles in the dry storage room.
Correction: The light intensity shall be at least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in the walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning. Properly distributed light makes the need for cleaning apparent by making accumulations of soil conspicuous.
- Physical Facilities/Repairing (repeated violation)
Observation: The baseboards around the walk-in cooling unit are damaged.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests (Critical)
Observation: Mouse droppings were observed around the water heater.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by using methods, if pests are found, such as trapping devices or other means of pest control as specified under sections 7-202.12, 7-206.12, and 7-206.13. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Drying Mops
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
|
01/26/2015 | Routine | |
House flies were observed inside the facility.
- Critical: Equipment Food-Contact Surfaces and Utensils/Cleaning Frequency (Critical)
Observation: The can opener blade needs cleaning.
Correction: Equipment food-contact surfaces and utensils shall be cleaned: (1) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry
|
09/02/2014 | Risk Factor | |
Faucet at the three-compartment sink observed in need of extending horizontally to reach all basins.
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An employee was eating at the food preparation unit.
Correction: An employee shall eat, drink, or use any form of tobacco only in designated areas where the contamination of exposed food
- Cooling Methods, Food containers (corrected on site)
Observation: Food container of sliced tomatoes and pizza sauce observed not arranged to provide maximum heat transfer and/or loosely covered, or uncovered while cooling (product was portioned in smaller containers by the person in charge).
Correction: When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (1) Arranged in equipment to provide maximum heat transfer through the container walls
- Equipment/Good Repair and Proper Adjustment
Observation: Door gasket to pizza preparation unit observed in need of repair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: Food slicer observed in need of cleaning and sanitizing.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Liquid Wastes and Rainwater/Nonsewage
Observation: Condensate drainage in the walk-in refrigerator was observed not draining properly.
Correction: Condensate drainage and other nonsewage liquids and rainwater shall be drained from point of discharge to disposal according to law. Liquid food wastes and rainwater can provide a source of bacterial contamination and support populations of pests. Proper storage and disposal of wastes and drainage of rainwater eliminate these conditions.
- Light Bulbs, Protective Shielding
Observation: Lights in the dry storage area observed not properly shielded.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles in the area where the slicer is located.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing
Observation: Hole observed in the wall next to the electrical panel. Hole observed in the top of the pizza preparation table.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Spray container of soap and water observed not properly labeled.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Critical: Poisonous or Toxic Materials/Separation/Spacing or Partitioning (corrected on site)
Observation: Containers of oven cleaner and degreaser observed stored on the same shelf with boxes of soda.
Correction: Poisonous or toxic materials shall be stored so they can not contaminate food, equipment, utensils, linens or single-service and single-use articles by separating the poisonous or toxic materials by spacing or partitioning. Separation of poisonous and toxic materials in accordance with the requirements of this section ensures that food, equipment, utensils, linen, and single-service and single-use articles are properly protected from contamination. For example, the storage of these types of materials directly above or adjacent to food could result in contamination of the food from spillage.
|
05/21/2014 | Routine | |
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: Both hand sinks are not accessible.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Hand Drying Provision (corrected on site) (repeated violation)
Observation: No paper towels at front hand sink.
Correction: Each handwashing sink or group of adjacent handwashing sinks shall be provided with: (A) Individual, disposable towels
- Critical: Food Manager Certificate and Responsibility (repeated violation)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
04/01/2014 | Other | |
CFM arrived on site. Establishment may now reopen, license is re-instated.
No violation noted during this evaluation. | 04/01/2014 | Follow-up | |
The establishment cooks meat and chicken. The profile needs to be updated.
Discontinue cooking with propane in the establishment.
Substantial compliance NOT observed.
Fact finding conference scheduled for March 4, 2014 at 10:30 AM. 800 S. Walter Reed Drive. 2nd floor.
- Critical: Hands and Arms/When to Wash (repeated violation)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Sponges, Use Limitation (repeated violation)
Observation: Sponges are used in contact with cleaned sanitized or in-use food-contact surfaces.
Correction: Sponges may not be used in contact with cleaned and sanitized or in-use food-contact surfaces. Sponges are difficult, if not impossible, to clean once they have been in contact with food particles and contaminants that are found in the use environment. Because of their construction, sponges provide harborage for any number and variety of microbiological organisms, many of which may be pathogenic. Therefore, sponges are to be used only where they will not contaminate cleaned and sanitized or in-use, food-contact surfaces such as for cleaning equipment and utensils before rinsing and sanitizing.
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: The microwave oven is not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Temperature Measuring Devices (repeated violation)
Observation: The Pepsi glass doors cooling unit is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The walk-in cooling unit shelve are heavily rusted. The water heater is damaged and rusted.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The nonfood-contact surface of the walk-in cooling unit fan covers and the pizza hood are dusty.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Kitchenware and Tableware/Preventing Contamination (repeated violation)
Observation: Knives, forks, and/or spoons are not presented so that only the handles are touched by employees and by consumers at the provided consumer self-service area.
Correction: Knives, forks, and spoons that are not prewrapped shall be presented so that only the handles are touched by employees and by consumers if consumer self-service is provided. The presentation of setting of single-service and single-use articles and cleaned and sanitized utensils shall be done in a manner designed to prevent the contamination of food- and lip-contact surfaces.
- Handwashing Cleanser, Availability
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink (front hand sink) .
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap.
- Hand Drying Provision (repeated violation)
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Mechanical/Ventilation
Observation: Mechanical ventilation of sufficient capacity is not provided to keep the kitchen free of excessive heat, steam, condensation, vapors, obnoxious odors, smoke, and/or fumes. Employees are cooking with propane in the kitchen without a ventilation hood.
Correction: If necessary to keep rooms free of excessive heat, steam, condensation, vapors, obnoxious odors, smoke and fumes, mechanical ventilation of sufficient capacity shall be provided. When mechanical ventilation is necessary, it must have adequate capacity to ensure that soiling of walls, ceilings, and other equipment is minimized
- Physical Facilities/Repairing (repeated violation)
Observation: The wall are above the pizza prep table needs repair. The back room and the walk-in cooling unit floors are damaged. The bathroom baseboards are damaged and loose. The back room floor tiles are cracked.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The wall area above the pizza prep table needs cleaning. The back room walls and ceiling are dirty.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Critical: Food Manager Certificate and Responsibility (corrected on site)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager. The certified food manager was not present at the start of the inspection.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
02/24/2014 | Follow-up | |
- Critical: Hands and Arms/When to Wash
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Tomato sauce a 90 F , discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/Commercially Processed Food
Observation: Sausages, ham and pepperoni prepared and packaged by a food processing plant opened and held for more than 24 hours were not clearly marked at the time the original container was opened in the food establishment to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature and time combination specified in paragraph (A) of this section and: (1) The day the original container is opened in the food establishment shall be counted as Day 1
- Sponges, Use Limitation
Observation: Sponges are used in contact with cleaned sanitized or in-use food-contact surfaces.
Correction: Sponges may not be used in contact with cleaned and sanitized or in-use food-contact surfaces. Sponges are difficult, if not impossible, to clean once they have been in contact with food particles and contaminants that are found in the use environment. Because of their construction, sponges provide harborage for any number and variety of microbiological organisms, many of which may be pathogenic. Therefore, sponges are to be used only where they will not contaminate cleaned and sanitized or in-use, food-contact surfaces such as for cleaning equipment and utensils before rinsing and sanitizing.
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: The microwave oven is not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Temperature Measuring Devices (repeated violation)
Observation: The Pepsi glass doors cooling unit is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Sanitizing Solutions, Testing Devices (repeated violation)
Observation: A test kit or other device that accurately measures the concentration of the sanitizing solution is not provided.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The walk-in cooling unit shelves are heavily rusted. The water heater is damaged and rusted.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The can opener blade is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surface of the walk-in cooling unit fan covers and the pizza hood are dusty.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Kitchenware and Tableware/Preventing Contamination (repeated violation)
Observation: Knives, forks, and/or spoons are not presented so that only the handles are touched by employees and by consumers at the provided consumer self-service area.
Correction: Knives, forks, and spoons that are not prewrapped shall be presented so that only the handles are touched by employees and by consumers if consumer self-service is provided. The presentation of setting of single-service and single-use articles and cleaned and sanitized utensils shall be done in a manner designed to prevent the contamination of food- and lip-contact surfaces.
- Physical Facilities/Repairing (repeated violation)
Observation: The wall area above the pizza prep table needs repair. The back room and the walk-in cooling unit floors are damaged. The bathroom baseboards are damaged and loose. The back room floor tiles are cracked.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions
Observation: The wall area above the pizza prep table needs cleaning. The back room walls and ceiling are dirty.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
01/13/2014 | Routine | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Raw shell eggs are stored over pasta in Pepsi glass upright.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Food Storage Containers, Identified with Common Name of Food (repeated violation)
Observation: Containers of flour and cornstarch are not identified with the common name of the food.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- Food Storage/Preventing Contamination from the Premises (repeated violation)
Observation: Containers storing bags of onions are stored on the floor of walk-in.
Correction: Store food where it is not exposed to splash, dust, or other contamination and/or install an approved, durable and cleanable barrier between the splash source and the food to prevent contamination.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Cheese in two door prep was 46F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment and Utensils/Durability and Strength
Observation: The Emerson microwave is not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Nonfood-Contact Surfaces
Observation: Soda crates are used as shelving.
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
- Temperature Measuring Devices (corrected on site)
Observation: The Pepsi glass upright is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Sanitizing Solutions, Testing Devices (repeated violation)
Observation: A test kit or other device that accurately measures the concentration of the sanitizing solution is not provided.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: Shelving in walk-in is rusted.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Kitchenware and Tableware/Preventing Contamination (corrected on site)
Observation: Knives, forks, and/or spoons are not presented so that only the handles are touched by employees.
Correction: Knives, forks, and spoons that are not prewrapped shall be presented so that only the handles are touched by employees and by consumers if consumer self-service is provided. The presentation of setting of single-service and single-use articles and cleaned and sanitized utensils shall be done in a manner designed to prevent the contamination of food- and lip-contact surfaces.
- Refuse/Toilet Room Receptacle, Covered
Observation: There is no covered receptacle in the toilet room used by females.
Correction: A toilet room used by females shall be provided with a covered receptacle for sanitary napkins. Garbage containers should be available wherever garbage is generated to aid in the proper disposal of refuse.
- Outer Openings, Protected (corrected on site) (repeated violation)
Observation: Front door was propped open.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Hand Drying Provision (corrected on site) (repeated violation)
Observation: No paper towels at rear kitchen hand sink.
Correction: Each handwashing sink or group of adjacent handwashing sinks shall be provided with: (A) Individual, disposable towels
- Intensity/Lighting
Observation: Inadequate lighting observed above reach-in where containers of lettuce, tomatoes, and onions are stored.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Physical Facilities/Repairing
Observation: The following observed in need of repair:
- wall by mop sink
- ceiling tiles are stained/damaged
- cove base in restroom.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Critical: Food Manager Certificate and Responsibility (corrected on site)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
02/04/2013 | Routine | |
Restaurant representatives - add corrected or new information about Pizza Bolis, 6033 Wilson Blvd, Arlington, VA 22205 »