1. Wash hands frequently.
2. New dish machine is installed
- Contamination from Hands/Preventing Contamination by Employees (corrected on site) (repeated violation)
Observation: Food employee contacting exposed RTE foods. Employees observed peeling mangoes, sticking lemon wedges on glasses of water and touching drinking ice with bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Non-Continuous Cooking for Raw Animal Foods
Observation: Raw animal foods (ahi tuna) that are cooked using a non-continuous process are not prepared or stored according to written procedures that have been approved by the regulatory authority.
Correction: Raw animal foods that are cooked using a non-continuous cook process shall be prepared and stored according to written procedures that: (1) have obtained prior approval from the regulatory authority
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Quinoa hot holding at the improper temperature of 95-107F. The cookers appears not functioning properly. The food was reheated and placed on the steam table.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The food-contact surface of the ice cream scoops, several food containers and lids stored as clean on a shelf above 3-compartment sink and a green cutting board are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
|
09/15/2015 | Risk Factor | |
1. Wash hands frequently.
2. High-temp warewahing machine is out of order. Three (3)-compartment sink is setup.
- Hands and Arms/When to Wash (corrected on site) (repeated violation)
Observation: A food employee failed to wash his or her hands before engaging in food preparation after touching bare human body parts.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Trays of raw-shelled eggs stored over butter and sushi ginger in the walk-in refrigerator.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Non-Continuous Cooking for Raw Animal Foods
Observation: Raw animal foods (salmon) that are cooked using a non-continuous process are not prepared or stored according to written procedures that have been approved by the regulatory authority.
Correction: Raw animal foods that are cooked using a non-continuous cook process shall be prepared and stored according to written procedures that: (1) have obtained prior approval from the regulatory authority
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Quinoa hot holding at the improper temperature of 113-117F.
Correction: (reheated) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Steamed brocoli cold holding at the improper temperature of 49F on top portion of the 2-door prep (sauce) refrigerator.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The food-contact surfaces of chopper on rack, a pitcher, tongs and peeler are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
|
05/28/2015 | Risk Factor | |
This is a follow-up to check high-temp warewashing machine. The machine has been repaired and turned the thermo-label black - attached to the report.
- Water/Pressure/Quantity and Availability (repeated violation)
Observation: No cold water at mop sink.
Correction: Water under pressure shall be provided to all fixtures, equipment, and nonfood equipment that are required to use water except that water supplied as specified under paragraphs 5-104.12(A) and (B) to a temporary food establishment or in response to a temporary interruption of a water supply need not be under pressure. Inadequate water pressure could lead to situations that place the public health at risk. For example, inadequate pressure could result in improper handwashing or equipment operation. Sufficient water pressure ensures that equipment such as mechanical warewashers operate according to manufacturer's specifications.
- Handwashing Signage (repeated violation)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at cookline handwashing sink used by food employees and/or is not clearly visible to food employees.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
|
02/02/2015 | Follow-up | |
1. No thermometer in wait station 1-dr ref (milk) - corrected.
2. Light bulb in "Traulsen" 2-dr glass refrigerator is not shielded.
A follow-up inspection will be performed on or after Wednesday, January 28, 2015 to check the dish machine and 3-compartment sink.
A Notice of Violation (NOV) will be issued if these issues are not addressed.
- Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: A tray of raw eggs stored over broccoli in 3-dr prep refrigerator.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Equipment/Good Repair and Proper Adjustment (corrected on site) (repeated violation)
Observation: High-temp warewashing machine and 3-compartment sink are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design. Three (3)-compartment sink is directly connected to cold water line (50F) which is not registering good quat sanitizer concentration. Manuall set up and use 3-compartment sink.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site) (repeated violation)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. High-temp warewashing machine did not turn thermo-label black, Manually set up and use 3-compartment sink until repaired.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Water/Pressure/Quantity and Availability
Observation: No cold water at mop sink.
Correction: Water under pressure shall be provided to all fixtures, equipment, and nonfood equipment that are required to use water except that water supplied as specified under paragraphs 5-104.12(A) and (B) to a temporary food establishment or in response to a temporary interruption of a water supply need not be under pressure. Inadequate water pressure could lead to situations that place the public health at risk. For example, inadequate pressure could result in improper handwashing or equipment operation. Sufficient water pressure ensures that equipment such as mechanical warewashers operate according to manufacturer's specifications.
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at cookline handwashing sink used by food employees and/or is not clearly visible to food employees.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
|
01/26/2015 | Routine | |
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized
Observation: The dishwashing machine did not turn thermolable tape black. Use the 3-part sink to sanitize until dishwashing machine is fixed.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Handwashing Sink/Using/Operation and Maintenance
Observation: The back handwashing sink is not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Hand Drying Provision
Observation: The bar hand sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at the bar hand sink.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Critical: Sanitizers, Criteria/Chemicals for Food Contact Surfaces (corrected on site)
Observation: The wiping cloth buckets sanitizer were measured at more than 500 ppm.
Correction: Chemical sanitizers and other chemical antimicrobials applied to food-contact surfaces shall meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions). Chemical sanitizers are included with poisonous or toxic materials because they may be toxic if not used in accordance with requirements listed in the Code of Federal Regulations (CFR). Large concentrations of sanitizer in excess of the CFR requirements can be harmful because residues of the materials remain. The CFR reference that is provided lists concentrations of sanitizers that are considered safe.
|
09/19/2014 | Risk Factor | |
| No violation noted during this evaluation. | 06/10/2014 | Follow-up | |
- Critical: Cooling, Cooked Food (corrected on site) (repeated violation)
Observation: Chicken wontons, cooked yesterday and found at 61F in 3-dr prep refrigerator was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
|
06/02/2014 | Follow-up | |
- Critical: Hands and Arms/When to Wash (corrected on site) (repeated violation)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Hands and Arms/Where to Wash (corrected on site)
Observation: A food employee was observed cleaning their hands in a food preparation sink.
Correction: Food employees shall clean their hands in a handwashing sink or approved automatic handwashing facility and may not clean their hands in a sink used for food preparation or warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste.
- Critical: Cooling, Cooked Food
Observation: Chiucken w/wontons, cooked yesterday and found at 61F in 3-dr prep refrigerator was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: The following foods were observed at improper cold holding temperature:
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site) (repeated violation)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. High-temp warewashing machine did not turn thermo-label black.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Critical: Food Manager Certificate and Responsibility (repeated violation)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
05/21/2014 | Risk Factor | |
The spray hose was corrected but continues to leak.
A part has been ordered for the kitchen warewashing machine. The kitchen warewashing machine is sanitizing properly.
All priority violations were corrected.
- Equipment and Utensils, Air-Drying Required (corrected on site) (repeated violation)
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Plumbing System/Maintained in Good Repair (repeated violation)
Observation: The spray hose leaks. .
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
|
01/22/2014 | Follow-up | |
Follow-up will be conducted to check repeat and priority violations.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Package Integrity (corrected on site)
Observation: Dented cans were observed on the dry storage rack. The cans were removed.
Correction: Food packages shall be in good condition and protect the integrity of the contents so that food is not exposed to adulteration or potential contaminants.
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Food employee contacting exposed RTE food with bare hands. An employee was observed putting garnish on a chicken dish with their bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Wiping Cloths, Use Limitation (corrected on site) (repeated violation)
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration. Premix system at the 3 compartment sink is not dispensing sanitizer.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Chicken & dumplings(43-51ºF) and egg rolls(46ºF) cold holding at improper temperatures 3 prep refrigerator. The TCS foods were iced down and relocated.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: 1. The 3 door pantry prep refrigerator is not maintaining TCS food at 41ºF or below. 2. The 3 compartment sink premix sanitizer system is not dispensing sanitizer. 3. The main warewashing machine is not reaching a wash temperature of a minimum of 160ºF.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food processor, slicer, and vegetable dicer are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. The chlorine sanitizer connected to the bar warewashing machine was empty. The quaternary ammonia at the 3 compartment sink is not dispensing enough sanitizer.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Equipment and Utensils, Air-Drying Required (repeated violation)
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink on the cookline is used for purposes other than handwashing. A utensil was observed in the basin of the sink and an employee was observed dumping water into the sink.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Plumbing System/Maintained in Good Repair
Observation: The spray hose leaks. .
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Critical: Food Manager Certificate and Responsibility (corrected on site)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
01/15/2014 | Routine | |
- Wiping Cloths, Use Limitation
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Wonton, spring roll, chicken pieces cold holding at the improper temperatures of 45-52oF in the 3-door prep refrigerator [ice down].
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment/Fixed, Spacing or Sealing
Observation: The kitchen dishwashing counter needs recaulking to its adjoining wall.
Correction: Counter-mounted equipment that is not easily movable shall be installed to allow cleaning of the equipment and areas underneath and around the equipment by being: (1) Sealed
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The soda gun nozzle holders are missing their drain tubes at the bar. A rice warmer/cooker has a damaged handle. The 3-door prep refrigerator is not maintaining foods 41oF or below. The back kitchen hood vent system has a gap in-between a couple of baffled vents.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency
Observation: Surfaces of the waitstation juicer are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surface of the kitchen prep refrigerator shelving and the wall shelving in the back kitchen are not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site)
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in the hot water mechanical operations by being cycled through equipment that is properly set up and/or achieving a utensil surface temperature of 160°F as measured by an irreversible registering temperature indicator [label did not turn completely black
Correction: water pressure found high (33 psi) during final rinse cycle and it should be 15-25 psi] [Utilize 3-part sink until repaired].
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site)
Observation: After being cleaned, glasses at the bar are not sanitized in a mechanical operations, using a proper solution [< 50ppm] [utlize 3-part sink until repaired].
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in chemical manual or mechanical operations, including the application of sanitizing chemicals by immersion, manual swabbing, brushing, or pressure spraying methods, using a solution as specified under section 4-501.114 by providing: (1) An exposure time of at least 10 seconds for a chlorine solution specified under paragraph 4-501.114(A), (2) An exposure time of at least 7 seconds for a chlorine solution of 50 mg/L that has a pH of 10 or less and a temperature of at least 38°C (100°F) or a pH of 8 or less and a temperature of at least 24°C (75°F), (3) An exposure time of at least 30 seconds for other chemical sanitizing solutions, or (4) An exposure time used in relationship with a combination of temperature, concentration, and pH that, when evaluated for efficacy, yields sanitization as defined in Subparagraph 1-201.10(B). Efficacious sanitization depends on warewashing being conducted within certain parameters. Time is a parameter applicable to both chemical and hot water sanitization. The time hot water or chemicals contact utensils or food-contact surfaces must be sufficient to destroy pathogens that may remain on surfaces after cleaning. Other parameters, such as rinse pressure, temperature, and chemical concentration are used in combination with time to achieve sanitization.
- Equipment and Utensils, Air-Drying Required (repeated violation)
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food [containers observed stacked while wet].
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located in the back kitchen next to the meat grinder was not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Plumbing System/Maintained in Good Repair
Observation: The dishsprayer is not maintained good repair. Adjust men's rest-room handsinks to have 100oF water. The 3-part sink stopper is not working properly.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Light Bulbs, Protective Shielding (repeated violation)
Observation: The light bulb over the potato starch prep area is not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Outer Openings, Protected
Observation: The outer openings of the food establishment are not protected against the entry of insects and rodents [air gaps at the rotating doors along the floor].
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Cleaning, Frequency and Restrictions
Observation: The walls & piping behind/under the cook-lines and dishwashing area are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Critical: Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Spray bottle used for storing poisonous or toxic materials is not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Critical: Food Manager Certificate and Responsibility (corrected on site)
Observation: The food establishment was not under the immediate control of a Northern Virginia certified food manager when I arrived.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
02/13/2013 | Routine | |
Restaurant representatives - add corrected or new information about P. F. Chang's China Bistro, 901 N Glebe Rd, Arlington, VA 22203 »