- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Butter hot holding at the improper temperature of 112ºF. Reheated to 165ºF.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Sanitizing Solutions, Testing Devices (repeated violation)
Observation: A chlorine test kit or other device that accurately measures the concentration of the sanitizing solution is not provided.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Equipment/Good Repair and Proper Adjustment
Observation: The 1 door upright refrigerator is rusty.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surfaces of the oven, refrigerator, shelves, exterior of the fryer, and microwave handle are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: Encrusted grease deposits and/or other soil accumulations were observed on the food-contact surfaces of the pans hanging above the 3 compartment sink.
Correction: The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur and to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equip/Utensils/Linens/Single-Service/Storage/Prohibitions
Observation: Clean pots under the 3 compartment sink on the floor.
Correction: Discontinue storage of clean equipment and utensils under un-shielded sewer lines or other areas subject to contamination.
- Outer Openings, Protected (repeated violation)
Observation: Air gaps were observed at the threshold of the back door.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors, walls, kitchen door, and the ceiling tiles are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/28/2016 | Routine | |
- The cutting boards are no longer easily cleanable.
- Clean the exterior of the refrigerator units.
- Clean the floor behind equipment.
- Remove the foil around the window oil.
- Clean the spice container tray.
- Grease trap cleaned twice in one week.
- No double pans in the prep refrigerator top.
No violation noted during this evaluation. | 10/09/2015 | Risk Factor | |
Clean the refrigerator, microwave, and rice cooker handles.
A replacement somosa warmer was ordered.
No violation noted during this evaluation. | 06/10/2015 | Risk Factor | |
*Remember to renew your Northern Virginia certified food managers license.
- Person in Charge/Duties/Employees Sanitizing Equipment
Observation: The person in charge is not ensuring employees are properly sanitizing cleaned multiuse
equipment and utensils before they are reused. A high concentration of bleach was observed in all 3 sink basins.
Correction:
- Sanitizing Solutions, Testing Devices (corrected on site)
Observation: A chlorine test kit or other device that accurately measures the concentration of the sanitizing solution is not provided. Corrected my instruction.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Cutting Surfaces
Observation: The surfaces of the cutting board on the prep refrigerator and the counter are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (corrected on site) (repeated violation)
Observation: The nonfood-contact surfaces of the refrigerators, microwave, seasoning tray, counters, fryers, and shelves are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surface of blender is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Outer Openings, Protected (repeated violation)
Observation: Air gaps were observed around the back door.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors, walls, and the bathroom are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Sanitizers, Criteria/Chemicals for Food Contact Surfaces (corrected on site)
Observation: The chlorine sanitizer observed at 200 PPM++ applied to food-contact surfaces does not meet requirements.
Correction: Chemical sanitizers and other chemical antimicrobials applied to food-contact surfaces shall meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions). Chemical sanitizers are included with poisonous or toxic materials because they may be toxic if not used in accordance with requirements listed in the Code of Federal Regulations (CFR). Large concentrations of sanitizer in excess of the CFR requirements can be harmful because residues of the materials remain. The CFR reference that is provided lists concentrations of sanitizers that are considered safe.
|
02/25/2015 | Routine | |
The floor corners need cleaning.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Tofu at 56 F inside the prep table.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
|
10/07/2014 | Risk Factor | |
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Container of rice, prepared previous day, observed in True 2 door prep unit at 51 F. Discarded.
Correction: Cooked foods must be cooled from 135 F to 70 F in 2 hours and to 41 F in a total of 6 hours.
|
06/16/2014 | Risk Factor | |
All priority violations were corrected.
- Nonfood-Contact Surfaces (repeated violation)
Observation: The nonfood-contact surfaces of the milk crates used as shelving are not free of unnecessary ledges, projections, and crevices, and/or designed and constructed to be easily cleanable or maintained.
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
|
03/25/2014 | Follow-up | |
NOV issued
- Critical: Food Display/Preventing Contamination by Consumers
Observation: Fresh snacks stored in containers without a hinged lid are not protected from consumer contamination.
Correction: Except for nuts in the shell and whole, raw fruits and vegetables that are intended for hulling, peeling, or washing by the consumer before consumption, food on display shall be protected from contamination by the use of packaging
- Cooling Methods (corrected on site)
Observation: Methods used for cooling rice can not be accomplished with the time and temperature criteria. A large container of rice was observed on the counter cooling. The rice was portioned into smaller containers and relocated to the refrigerators to continue the cooling process.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: (REPEAT) Potato samosas hot holding at the improper temperature of 130-133ºF in the display warmer. Discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: (REPEAT) Diced tomatoes(56ºF), tofu(51ºF), and cauliflower(46ºF) cold holding at improper temperatures in the 2 door prep refrigerator. Relocated and the temperature was adjusted.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Nonfood-Contact Surfaces
Observation: The nonfood-contact surfaces of the soda/milk crates used a shelving and the cardboard used as liners are not free of unnecessary ledges, projections, and crevices, and/or designed and constructed to be easily cleanable or maintained.
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surfaces of the fryer, ovens, all refrigerators, and the microwaves are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Refuse/Maintaining Refuse Areas and Enclosures (corrected on site)
Observation: The storage area and/or enclosure for refuse, recyclables, or returnables is not maintained free of unnecessary items and/or clean. Bags of trash were observed stack near the back door.
Correction: A storage area and enclosure for refuse, recyclables, or returnables shall be maintained free of unnecessary items, as specified under section 6-501.114, and clean. Proper storage and disposal of garbage and refuse are necessary to minimize the development of odors, prevent such waste from becoming an attractant and harborage or breeding place for insects and rodents, and prevent the soiling of food preparation and food service areas. Improperly handled garbage creates nuisance conditions, makes housekeeping difficult, and may be a possible source of contamination of food, equipment, and utensils.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors and walls throughout the kitchen and behind the front counter are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: The ventilation hood system has not been professionally cleaned since 6/12.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
|
02/20/2014 | Routine | |
1. The buffet has been removed
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site)
Observation: Samosas hot holding at the improper temperature of 114F in display warmer.
Correction: (reheated) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Fried paneer (cheese), Chicken curry and Chickpeas (45F) in "True" 2-dr prep refrigerator and Cheese blacks (46F) in "True" 2-door sliding glass refrigerator were observed at improper cold holding temperature. Yogurt (67F) and Tomatoes (66F) were on prep board (discarded).
Correction: (relocated into other refrigerators and freezers) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation (repeated violation)
Observation: Several foods (chicken curry, chickpeas, etc.), prepared in an off-site location and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink has a stack of food trays and utensils stored on basin and is not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Handwashing Cleanser, Availability (corrected on site)
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap.
|
10/07/2013 | Risk Factor | |
Absence of "No Smoking" sign.
NOV Enforcement lifted.
- Responsibilities of Owner or Proprietor (repeated violation)
Observation: Absence of no-smoking signs or international no-smoking signs in non-smoking area.
Correction: Post no-smoking signs or international no-smoking signs in the non-smoking area.
These can be found online at www.vdh.virginia.gov/breatheasy
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surface of the equipment throughout the kitchen is not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors, walls, and ceilings throughout the establishment and the toilet facility and fixtures are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
07/30/2013 | Follow-up | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (repeated violation)
Observation: Food is not in packages, covered containers, or wrappings. Observed foods uncovered in refrigeration units.
Correction: Food shall be protected from cross contamination by storing the food in packages, covered containers, or wrappings. This section does not apply to: (1) Whole, uncut, raw fruits and vegetables and nuts in the shell, that require peeling or hulling before consumption
- Food Storage/Preventing Contamination from the Premises (repeated violation)
Observation: Stored food is not protected from contamination. Observed dry foods in uncovered containers and packages of dry foods on the floor.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: Observed foods in the True 2 door prep unit cold holding at improper temperatures (potatoes 47 F, chicken curry 46 F, curry sauce 50 F). Manager advised food was out of temperature. No correction made during inspection.
Observed packaged (gallon containers) of milk holding in the True 2 door sliding glass door cooler with cooler reading 60 F. Milk was moved to walk-in cooler.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation (repeated violation)
Observation: Various foods prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: The General Electric microwave and the Ultra grinder are not designed and constructed to be durable (commercial use).
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Nonfood-Contact Surfaces (repeated violation)
Observation: The nonfood-contact surface of the milk crates used for storage are not free of unnecessary ledges, projections, and crevices, and/or designed and constructed to be easily cleanable or maintained.
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surface of the equipment throughout the kitchen is not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (repeated violation)
Observation: The utensils and cutting boards are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink located in the kitchen is not maintained so that it is accessible at all times for employee use. Observed utensils stacked on top of sink.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Outer Openings, Protected (repeated violation)
Observation: The outer openings of the food establishment are not protected against the entry of insects and rodents. Observed front doors propped open upon entry to the establishment (air conditioning not operating). Observed gap along bottom threshold of rear exit door.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Hand Drying Provision
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors, walls, and ceilings throughout the establishment and the toilet facility and fixtures are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
06/26/2013 | Routine | |
- Responsibilities of Owner or Proprietor
Observation: Absence of no-smoking signs or international no-smoking signs in non-smoking area.
Correction: Post no-smoking signs or international no-smoking signs in the non-smoking area.
These can be found online at www.vdh.virginia.gov/breatheasy
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Foods in Artic upright are not covered/protected.
Correction: Food shall be protected from cross contamination by storing the food in packages, covered containers, or wrappings. This section does not apply to: (1) Whole, uncut, raw fruits and vegetables and nuts in the shell, that require peeling or hulling before consumption
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Raw shell eggs were stored over ready-to-eat foods in Artic upright.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Critical: Food Contact with Equipment and Utensils/Preventing Contamination (corrected on site)
Observation: Container of food was stored directly on top of other uncovered foods. Bowls and ramekins are used as scoops.
Correction: Food shall only contact surfaces of: (A) Equipment and utensils that are cleaned as specified under Part 4-6 of this Code and sanitized as specified under Part 4-7 of this Code
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Utensils are stored in water at 70F.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Food Storage/Preventing Contamination from the Premises (corrected on site)
Observation: Bowl of dough observed stored on floor under shelf.
Correction: Store food where it is not exposed to splash, dust, or other contamination and/or install an approved, durable and cleanable barrier between the splash source and the food to prevent contamination.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation
Observation: Foods prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: Cloth observed under cutting board.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment and Utensils/Durability and Strength
Observation: The General microwave and Ultra Grinder are not commercial.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Nonfood-Contact Surfaces
Observation: Milk crates are used as shelving.
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
- Temperature Measuring Devices (corrected on site)
Observation: True 2dr. prep is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing (corrected on site)
Observation: Clean utensils are stored in dirty containers.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Outer Openings, Protected
Observation: Gap observed along bottom threshold of rear exit door.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Intensity/Lighting
Observation: Light is out in right upright freezer.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Cleaning, Frequency and Restrictions
Observation: The following observed in need of cleaning:
- restroom ceiling tiles are stained
- kitchen ceiling tiles are stained
- wall behind equipment
- exhaust in restroom observed with dust accumulation.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Cleaning of Plumbing Fixtures
Observation: Hand sink faucet is not clean.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
|
01/28/2013 | Routine | |
Restaurant representatives - add corrected or new information about Minerva Express, 4815-B Lee Hwy, Arlington, VA 22207 »