- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface(s) of the wiping cloth under the cutting board is(are) not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Cleaning, Frequency and Restrictions
Observation: The floor of the walk in freezer was in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/15/2016 | Routine | |
A dog was observed under customer's seat in dining room, which is not in compliance with Section 2-403 (Animals), of the FDA food code.
Deli meats, breads, pastries, muffins, cut fruit, etc., must be protected from contamination at conference buffets.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Creamers requiring refrigeration were observed on tables in bowls at 70 F. Deli meats were on the conference buffet at 60-63 F. Items were discarded, and TPHC information was provided.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surfaces of the canopener blade are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Poisonous or Toxic Materials/Restrictions/Presence and Use (corrected on site)
Observation: Hot Shot Kitchen Bug Killer is not required for the operation and maintenance of the food establishment.
Correction: Only those poisonous or toxic materials that are required for the operation and maintenance of the establishment, such as for the cleaning and sanitizing of equipment and utensils and the control of insects and rodents, shall be allowed in the food establishment. This section does not apply to packaged poisonous or toxic materials that are for retail sale. The presence in the establishment of poisonous or toxic materials that are not required for the maintenance and operation of the establishment represents an unnecessary risk to both employees and consumers. Preserving food safety depends in part on the appropriate and proper storage and use of poisonous or toxic materials that are necessary to the maintenance and operation of a food establishment. Even those that are necessary can pose a hazard if they are used in a manner that contradicts the intended use of the material as described by the manufacturer on the material's label. If additional poisonous or toxic materials are present, there is an unwarranted increased potential for contamination due to improper storage (e.g., overhead spillage that could result in the contamination of food, food-contact surfaces, or food equipment) or inappropriate application.
|
11/13/2015 | Risk Factor | |
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site)
Observation: Pancake batter held for mare than 24 hours not properl labeled. Corrected by instruction.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment/Good Repair and Proper Adjustment
Observation: Handles on several refrigerators observed in poor repair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: Fryer observed in need of cleaning.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
|
04/01/2015 | Routine | |
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Deli cheese was holding at 62 F, grated cheese at 60 F, sliced tomatoes at 60 F in the malfunctioning prep unit. Items discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Critical: Food Manager Certificate and Responsibility
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager. CFM's card was expired by approx. a month.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
11/24/2014 | Risk Factor | |
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Grilled chicken at 47 F, discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
|
06/24/2014 | Risk Factor | |
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface(s) of the milk crates used as shelving in walk in is(are) not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Plumbing System/Maintained in Good Repair
Observation: The backflow prevention device on the mop sink was observed leaking and in disrepair.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: Intake and exhaust air ducts are not clean and/or filters are not changed. Ceiling vents above cook line in kitchen observed with accumulation of dust.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
|
02/27/2014 | Routine | |
A detailed written procedure was given to the CFM.
Clean the slicer after every use or every 4 hours while in use. Wash, rinse, and sanitize all parts.
- Critical: Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens (repeated violation)
Observation: There are no asterisks in the dinner menu on food items that are served raw or under cooked. (NY strip, today's fresh fish, steak frites salad, and burgers are missing an asterisk).
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (corrected on site) (repeated violation)
Observation: The slicer is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency (corrected on site) (repeated violation)
Observation: The interior surface of the soda gun at the bar is not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
|
10/23/2013 | Risk Factor | |
Ensure that Time As A Public Health Control procedures are followed. Always document the actual time the food is taken out of temperature control (refrigerator). May need to add rows on log chart for additional food which is put out during breakfast.
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: Observed foods cold holding on ice at improper temperatures (spinach 55 F, liquid egg 67 F, shredded cheese 54 F).
Observed salmon on counter at 50-56 F. Foods were moved to refrigerator.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: The food establishment serves or sells raw or undercooked food and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. Establishment serves hamburgers and steaks to order, no Consumer Advisory on the menu.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency
Observation: Surfaces of the inside of the ice machine, ice scoop holder, and soda gun at the bar are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink located next to dish wash area is not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
|
06/21/2013 | Risk Factor | |
1. Post 2013 food permit conspicuously to the public.
2. Replace bar blender lid (currently missing middle piece).
- Critical: Package Integrity (corrected on site)
Observation: A couple of cans were observed with dents on their seams.
Correction: Food packages shall be in good condition and protect the integrity of the contents so that food is not exposed to adulteration or potential contaminants. Properly segregate/label not to be used awaiting redemption/credit.
- Critical: Time as a Public Health Control (corrected on site)
Observation: No written procedures exist for the use of time only as a public health control for a working supply of food items on the buffet (deli meats, cheeses, lox) (I provided written procedures to the manager).
Correction: If time only is used as the public health control for a working supply of potentially hazardous food (time/temperature control for safety food) before cooking, or for ready-to-eat potentially hazardous food (time/temperature control for safety food) that is displayed or held for service for immediate consumption: (1) Written procedures shall be prepared in advance, maintained in the food establishment and made available to the regulatory authority upon request that specify: (a) Methods of compliance with Subparagraphs (B) (1)-(3) or (C) (1)-(5) of this section
- Critical: Time Public Health Control/Time - Maximum up to 4 Hours/Marked (corrected on site) (repeated violation)
Observation: The deli meats, cheeses, and lox for which time only, rather than time in conjunction with temperature control, is not properly labeled to indicate the time it shall be discarded at the buffet.
Correction: If time only, rather than time in conjunction with temperature control, up to a maximum of 4 hours, is used as the public health control: The food shall be marked or otherwise identified to indicate the time that is 4 hours past the point in time when the food is removed from temperature control.
- Sanitizing Solutions, Testing Devices
Observation: A test kit or other device that accurately measures the concentration of the sanitizing solution is not provided.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (corrected on site)
Observation: The slicer, can opener, and kitchen blender are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Refuse/Covering Receptacles (corrected on site)
Observation: Receptacles and/or waste handling units for refuse, recyclables, and/or returnables kept outside the food establishment are not kept covered with tight-fitting lids or doors.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
|
01/23/2013 | Routine | |
Restaurant representatives - add corrected or new information about Hilton Garden Inn-Arlington/Shirlington-Restaurant, 4271 Campbell Ave, Arlington, VA 22206 »