- Ventilation Hood-Systems, Drip Prevention/Functionality
Observation: The exhaust ventilation hood system is missing drip pan under the baffles which keeps the grease or condensation from draining or dripping onto food, equipment, utensils, linens, single-service and single-use articles.
Correction: Exhaust ventilation hood systems in food preparation and warewashing areas including components such as hoods, fans, guards, and ducting shall be designed to prevent grease or condensation from draining or dripping onto food, equipment, utensils, linens, single-service and single-use articles. The dripping of grease or condensation onto food constitutes adulteration and may involve contamination of the food with pathogenic organisms. Equipment, utensils, linens, and single service and single use articles that are subjected to such drippage are no longer clean.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The following equipment is not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design:
1. dish racks used in mechanical dish machine
2. two door refrigerator (inside damaged, rusted shelves and damaged gaskets).
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: Observed food-contact surfaces of utensils and containers/pans stored as clean not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing station at the bar is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Conveying Sewage/Operation and Maintenance (corrected on site)
Observation: Observed drain pipes are leaking on three compartment sink. Manager called technician during inspection to repair.
Correction: Sewage shall be conveyed to the point of disposal through an approved sanitary sewage system or other system, including use of sewage transport vehicles, waste retention tanks, pumps, pipes, hoses, and connections that are constructed, maintained, and operated according to law. Improper disposal of waste provides a potential for contamination of food, utensils, and equipment and, therefore, may cause serious illness or disease outbreaks. Proper removal is required to prevent contamination of ground surfaces and water supplies, or creation of other insanitary conditions that may attract insects and other vermin.
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food (over cookline).
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Intensity/Lighting
Observation: The light intensity is below 10 foot candles in the walk-in refrigerator.
Correction: The light intensity shall be at least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in the walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning. Properly distributed light makes the need for cleaning apparent by making accumulations of soil conspicuous.
- Controlling Pests (Pf) (repeated violation)
Observation: Proper pest control methods are not used to maintain the premises free of insects, rodents, and other pests. Observed rodent droppings in the kitchen.
Correction: The premises shall be maintained free of insects, rodents, and other pests. The presence of insects, rodents, and other pests shall be controlled to eliminate their presence on the premises by using methods, if pests are found, such as trapping devices or other means of pest control as specified under sections 7-202.12, 7-206.12, and 7-206.13.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors and walls in the kitchen and rest rooms are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/15/2016 | Routine | |
| No violation noted during this evaluation. | 12/09/2015 | Follow-up | |
A follow up inspection will be conducted in thirty (30) days on or after December 4, 2015 to ensure Priority and Priority Foundation items are corrected.
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site) (repeated violation)
Observation: An open beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Food Storage/Preventing Contamination from the Premises
Observation: Observed rice and oil stored on the floor not protected from contamination.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Observed shredded cheese and sour cream cold holding at the improper temperature of 46 F in the walk-in cooler. Foods were relocated to another refrigerator. Inside temperature of the walk-in 46 F. All other foods in the walk-in were not temperature control for safety (TCS) foods for (produce). Observed rice out on the counter at 54 F. rice was discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Food-Contact Surfaces/Cleanability
Observation: The food-contact surface of the plastic containers used for chip storage are no longer smooth, free of breaks, open seams, cracks, chips, inclusions, pits, similar imperfections, finished to have smooth welds and joints, and/or accessible for cleaning and inspection by an approved method.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The walk-in cooler is not maintaining an ambient air temperature of 41 f or below.
The gaskets/seals on the True one door/two drawer prep unit are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair.
Observed storage shelving tied together with string and plastic wrap.
Observed prep table beside of prep unit rusted and no longer smooth, easily cleanable.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: Encrusted grease deposits and/or other soil accumulations were observed on the food-contact surfaces of the frying pans.
Correction: The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur and to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surfaces of the equipment throughout the kitchen are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The food-contact surfaces of dishes and utensils stored as clean are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Physical Facilities/Repairing (repeated violation)
Observation: Observed floor tile in need of repair in the kitchen (food debris and water build up in broken areas.
The wall in the men's toilet room is in need of repair.
The floor mats are in poor condition.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests (Critical)
Observation: Proper pest control methods are not used to minimize the presence of insects, rodents, and other pests found in the establishment. Observed roaches on the floor and on the wall in the kitchen.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by using methods, if pests are found, such as trapping devices or other means of pest control as specified under sections 7-202.12, 7-206.12, and 7-206.13. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Maintaining Premises, Unnecessary Items and Litter (repeated violation)
Observation: The premises is not free of items that are unnecessary to the operation or maintenance of the establishment. The small reach-in refrigerator is not in operation and being used for storage. Discontinue use and remove from establishment (may harbor pests).
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors and walls are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
11/04/2015 | Routine | |
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: Observed several open beverage containers not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Safe, Unadulterated, and Honestly Presented/Condition (corrected on site)
Observation: Observed food in the walk-in cooler with mold growing on top. Food was discarded.
Correction: Food shall be safe, unadulterated, and, as specified under section 3-601.12, honestly presented.
- In-Use Utensils, Between-Use Storage (corrected on site) (repeated violation)
Observation: Food preparation and dispensing utensils are improperly stored in standing water.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Wiping Cloths, Use Limitation (corrected on site)
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Cooling, Cooked Food (corrected on site)
Observation: Sauces that were prepared yesterday were not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less. Food was discarded.
- Ready-to-Eat,Time/Temperature Control for Safety Food, Disposition (corrected on site)
Observation: Several containers of food in the walk-in cooler are marked with a date or day that exceeds the temperature and time combination. Foods were discarded.
Correction: A food specified in paragraph 3-501.17(A) or (B) shall be discarded if it: (1) Exceeds the temperature and time combination of paragraph 3-501.17(A), except time that the product is frozen
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The gaskets/seals on the True one door/two drawer prep unit are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair.
Observed storage shelving tied together with string and plastic wrap.
Observed prep table beside of prep unit rusted and no longer smooth, easily cleanable.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surfaces of the shelving in the kitchen are not kept free of an accumulation of grease, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (repeated violation)
Observation: Surfaces of the ice machine are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Sink/Using/Operation and Maintenance (repeated violation)
Observation: The handwashing sinks at the bar and in the kitchen are being used for purposes other than handwashing.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Plumbing System/Maintained in Good Repair
Observation: Observed drain pipe leaking on the handwashing sink is not in maintained good repair.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Hand Drying Provision
Observation: The handwashing sink in the kitchen is not provided with individual, disposable towels.
Correction: Each handwashing sink or group of adjacent handwashing sinks shall be provided with: (A) Individual, disposable towels
- Physical Facilities/Repairing (repeated violation)
Observation: Observed floor tile in need of repair in the kitchen (food debris and water build up in broken areas.
The wall in the men's toilet room is in need of repair.
The floor mats used in the kitchen are in poor condition.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Maintaining Premises, Unnecessary Items and Litter
Observation: Observed nonfunctioning equipment for storage and prepping (top) food.
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
|
04/21/2015 | Routine | |
The hand sink at the bar is use as a dump sink.
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination
Observation: Several food containers inside the walk-in and reach-in cooling units were not covered.
Correction: Food shall be protected from cross contamination by storing the food in packages, covered containers, or wrappings. This section does not apply to: (1) Whole, uncut, raw fruits and vegetables and nuts in the shell, that require peeling or hulling before consumption
|
10/20/2014 | Risk Factor | |
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Refried beans covered and stacked in the upright two door refrigerator made yesterday were not cooled within within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less
Correction: they were found at 48 F. The facility was instructed to discard this product.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Cheeses in the walk-in refrigerator and in the top portion of the cook's prep refrigerator top portion were cold holding at the improper temperatures of 48-50 F. The prep refrigerator was adjusted to a colder setting
Correction: the manager was instructed that the walk-in refrigerator also needed to be adjusted to a colder setting and/or repaired to keep foods 41 F and below.
|
06/19/2014 | Risk Factor | |
- In-Use Utensils, Between-Use Storage (repeated violation)
Observation: Food preparation and dispensing utensils are improperly stored. Observed knives stored on dirty shelving. Observed utensils stored in standing water.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Equipment/Fixed, Spacing or Sealing (repeated violation)
Observation: The three compartment sink is no longer sealed to the wall.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The ice machine (inside plate) and the 3 door freezer (shelves tied together with string) are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, and Utensils
Observation: Observed utensils and cutting board stored as clean were not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the inside of the ice machine and the soda gun at the bar are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Sink/Using/Operation and Maintenance
Observation: The handwashing sink in the kitchen is used for purposes other than handwashing.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Physical Facilities/Repairing
Observation: Observed broken floor tiles in kitchen.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions
Observation: The walls behind equipment and around dish machine are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers (spray bottles) used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
03/20/2014 | Routine | |
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Employees observed contacting ready-to-eat (RTE) food (slicing lemons) and pouring drinking ice for drinks with their bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph (D) of this section, food employees may not contact exposed, RTE food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Trays of raw eggs stored over spinach, cheese and tortillas in "True" 1-door/2-drawer refrigerator.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Food preparation and dispensing utensils are improperly stored in standing water at room temperature and in between trash cans and shelves.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Cooked pork, cooked yesterday and observed at 53F in the walk-in refrigerator, was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
- Cooling Methods (corrected on site)
Observation: Methods used for cooling cooked foods (pork, rice) can not be accomplished with the time and temperature criteria.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: The following foods were observed at improper cold holding temperature:
1. Pico de gallo (46F) in "Superior" 2-dr prep.
2. Rice (45-48F) in 1-dr reach-in.
3. Half-n-half in 2-door reach-in bar refrigerator.
Correction: (corrected) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Temperature Measuring Devices
Observation: The temperature measuring device of "Superior" 3-dr freezer and walk-in refrigerator (outside) are broken and not easily readable.
Correction: Temperature measuring devices shall be designed to be easily readable. The importance of maintaining potentially hazardous (time/temperature control for safety) foods at the specified temperatures requires that temperature measuring devices be easily readable. The inability to accurately read a thermometer could result in food being held at unsafe temperatures.
- Temperature Measuring Devices
Observation: The "Superior" 2-dr prep is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Fixed, Spacing or Sealing
Observation: Kitchen, bathroom and 3-compartment sinks are not sealed to their adjoining walls.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment/Good Repair and Proper Adjustment
Observation: Gaskets of "Superior" 2-dr upright are torn
Correction: water is dripping from the compressor of walk-in onto produce (corrected) and ice machine are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surface of the kitchen wired shelves and exterior of microwave oven is not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (corrected on site) (repeated violation)
Observation: The food-contact surface dirty knives and choppers stored in between trash cans and dirty shelves is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Grease Trap/Location and Placement
Observation: There is no grease trap in line at 3-compartment sink.
Correction: If used, a grease trap/interceptor shall be located to be easily accessible for cleaning. Failure to locate a grease trap/interceptor so that it can be properly maintained and cleaned could result in the harborage of vermin and/or the failure of the sewage system.
- Refuse/Covering Receptacles (corrected on site)
Observation: Receptacles and/or waste handling units for refuse, recyclables, and/or returnables kept outside the food establishment are not kept covered with tight-fitting lids or doors.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
- Toilet Rooms, Enclosed
Observation: Both toilet rooms are not completely enclosed and/or provided with a tight-fitting and/or self-closing door.
Correction: Except where a toilet room is located outside a food establishment and does not open directly into the food establishment such as a toilet room that is provided by the management of a shopping mall, a toilet room located on the premises shall be completely enclosed and provided with a tight-fitting and self-closing door. Completely enclosed toilet facilities minimize the potential for the spread of disease by the movement of flies and other insects between the toilet facility and food preparation areas.
- Outer Openings, Protected
Observation: The outer openings of the food establishment are not protected against the entry of insects and rodents. Big gap on the side door in kitchen towards dumpster area.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
|
05/16/2013 | Routine | |
- Controlling Pests
Observation: Mouse droppings were observed in the furnance closet.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
|
02/11/2013 | Complaint | |
Restaurant representatives - add corrected or new information about Guajillo Grill, 1727 Wilson Blvd, Arlington, VA 22209 »