- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Half 'n 'half and whipped cream cold holding at the improper temperature of 52 F inside the bar keg refrigerator
Correction: relocated. Milk cold holding at the improper temperature of 43 F in the server three door counter refrigerator
- Nonfood-Contact Surfaces/Nonabsorbent (corrected on site)
Observation: The cloth used under the cutting boar is not corrosion-resistant and/or nonabsorbent.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Temperature Measuring Devices
Observation: The bar keg refrigerator is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Beverage Tubing, Separation (repeated violation)
Observation: Beverage tubing and a cold-plate beverage cooling device are in contact with ice used for drinks at the bar.
Correction: Except for cold plates that are constructed integrally with an ice storage bin, beverage tubing and cold-plate beverage cooling devices may not be installed in contact with stored ice. Beverage tubing and coldplate cooling devices may result in contamination if they are installed in direct contact with stored ice. Beverage tubing installed in contact with ice may result in condensate and drippage contaminating the ice as the condensate moves down the beverage tubing and ends up in the ice. The presence of beverage tubing and/or coldplate cooling devices also presents cleaning problems. It may be difficult to adequately clean the ice bin if they are present. Because of the high moisture environment, mold and algae may form on the surface of the ice bins and any tubing or equipment stored in the bins.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The keg refrigerator and the server three door counter refrigerator are not maintaining dairy products at 41 F or below.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Utensils and Temperature and Pressure Measuring Devices/Good Repair and Calibration
Observation: The ambient air temperature measuring device in the upright three door refrigerator is not maintained in good repair.
Correction: Ambient air temperature, water pressure, and water temperature measuring devices shall be maintained in good repair and be accurate within the intended range of use. A utensil or food temperature measuring device can act as a source of contamination to the food it contacts if it is not maintained in good repair. Also, if temperature or pressure measuring devices are not maintained in good repair, the accuracy of the readings is questionable. Consequently, a temperature problem may not be detected, or conversely, a corrective action may be needlessly taken.
- Equipment, Food-Contact Surfaces, and Utensils (repeated violation)
Observation: The food-contact surfaces of the slicer, cutting boards, french fry slicer and the soda gun nozzlesvare not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The nonfood-contact surfaces of the condiment shelving, inside the three door prep refrigerator and the floor inside the keg refrigerator are not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing (repeated violation)
Observation: Cups and glasses at the bar are not stored in a self-draining position that allows air drying.
Correction: Clean equipment and utensils shall be stored as specified under paragraph (A) of this section and shall be stored: (1) In a self-draining position that allows air drying
- Refuse/Maintaining Refuse Areas and Enclosures
Observation: The storage area and/or grease dumpster is not maintained clean.
Correction: A storage area and enclosure for refuse, recyclables, or returnables shall be maintained free of unnecessary items, as specified under section 6-501.114, and clean. Proper storage and disposal of garbage and refuse are necessary to minimize the development of odors, prevent such waste from becoming an attractant and harborage or breeding place for insects and rodents, and prevent the soiling of food preparation and food service areas. Improperly handled garbage creates nuisance conditions, makes housekeeping difficult, and may be a possible source of contamination of food, equipment, and utensils.
- Light Bulbs, Protective Shielding (repeated violation)
Observation: The light bulbs in the ceiling of the back portion of the kitchen, the light bulb inside the upright three door refrigerator and the upright one door refrigerator are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Outer Openings, Protected (repeated violation)
Observation: The outer openings of the food establishment are not protected against the entry of insects and rodents. The back door was found open
Correction: when closed their is still an air gap under the door.
- Physical Facilities/Repairing (repeated violation)
Observation: The bar floor is no longer smooth and easily cleanable. There are some damaged floor tiles under the fryer. There is a hole in the wall behind the dish sprayer and by the steamtable. The wall floor junctures by the back door and downstairs are not maintained in good repair. There are water damaged ceiling tiles in the basement.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors are not cleaned as often as necessary to keep them clean. Not all shelves are six inches above the floor. The walls by the prep refrigerator and steamtable are not kept clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Poisonous or Toxic Materials/Common Name/Working Containers (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the materials (spray bottles).
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
03/08/2016 | Routine | |
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Foods inside the kitchen sliding door refrigerator and the one door refrigerator cold holding at the improper temperatures of 58-65 F. These foods were discarded. Do not store time/temperature control for safety foods inside these refrigerators until they can hold foods at or below 41 F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (repeated violation)
Observation: The food-contact surfaces of slicer are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Poisonous or Toxic Materials/Common Name/Working Containers (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material (spray bottle by slicer).
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
07/20/2015 | Risk Factor | |
- Food Manager Certificate and Responsibility (corrected on site)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
12/16/2014 | Follow-up | |
- Critical: Cooling, Ambient Ingredients (corrected on site)
Observation: Cut lettuce and cut tomatoes prepared from ingredients at ambient temperature were not cooling within 4 hours to 5ºC (41ºF) in the top portion of the sandwich prep refrigerator. These items were relocated down inside the bottom portion of the refrigerator.
Correction: Time/temperature control for safety food shall be cooled within 4 hours to 5ºC (41ºF) or less, if prepared from ingredients at ambient temperature, such as reconstituted foods and canned tuna. Safe cooling requires removing heat from food quickly enough to prevent microbial growth. Excessive time for cooling of time/temperature control for safety foods has been consistently identified as one of the leading contributing factors to foodborne illness. During slow cooling, time/temperature control for safety foods are subject to growth of a variety of pathogenic microorganisms. If the food is not cooled in accordance with this Code requirement, pathogens may grow to sufficient numbers to cause foodborne illness.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink located at the bar is not maintained so that it is accessible at all times for employee use (trashcan and box stored in front of it).
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Critical: Food Manager Certificate and Responsibility (corrected on site)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager (expired card). The manager was instructed to obtain a new card within 30 days.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
11/17/2014 | Risk Factor | |
- Critical: Time/Temperature Control for Safety Food, Cold Holding
Observation: Walk in was maintaining an ambient temperature of greater than 41 F. Pepperjack cheese was at 45 F, ground beef was at 42 F, milk was at 45 F. Service call placed for unit.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Sliced, portioned deli cheeses, prepared and held in the food establishment for more than 24 hours were not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Critical: Food Manager Certificate and Responsibility
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager. CFM's card had expired.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
07/18/2014 | Risk Factor | |
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Observed a pan of raw beef sitting directly on top of cooked chicken. Observed raw bacon stored above ready to eat food.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Dry food is not in covered containers.
Correction: Food shall be protected from cross contamination by storing the food in packages, covered containers, or wrappings. This section does not apply to: (1) Whole, uncut, raw fruits and vegetables and nuts in the shell, that require peeling or hulling before consumption
- Beverage Tubing, Separation
Observation: Beverage tubing and a cold-plate beverage cooling device are in contact with ice used for drinks.
Correction: Except for cold plates that are constructed integrally with an ice storage bin, beverage tubing and cold-plate beverage cooling devices may not be installed in contact with stored ice. Beverage tubing and coldplate cooling devices may result in contamination if they are installed in direct contact with stored ice. Beverage tubing installed in contact with ice may result in condensate and drippage contaminating the ice as the condensate moves down the beverage tubing and ends up in the ice. The presence of beverage tubing and/or coldplate cooling devices also presents cleaning problems. It may be difficult to adequately clean the ice bin if they are present. Because of the high moisture environment, mold and algae may form on the surface of the ice bins and any tubing or equipment stored in the bins.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surfaces of the equipment in the kitchen are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the inside of the ice machine and the soda guns at the bar are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Cleaned equipment and utensils observed improperly stored on the floor and in dirty bins.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Light Bulbs, Protective Shielding
Observation: The light bulbs in the rear kitchen area are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Physical Facilities/Repairing
Observation: The walls, floor at bar and floor in walk-in are not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Maintaining Premises, Unnecessary Items and Litter
Observation: The premises is not free of items that are unnecessary (rusty paint cans stored on floor in basement) to the operation or maintenance of the establishment.
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
- Cleaning, Frequency and Restrictions
Observation: The floors, walls and ceilings are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers (spray bottles) used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
03/27/2014 | Routine | |
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Clam chowder was not cooled in 6 hours. The soup was observed in a large container. Discarded.
Correction: Cooked potentially hazardous food (time/temperature control for safety food) shall be cooled: (1) Within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (repeated violation)
Observation: The slicer is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located in the kitchen was not maintained so that it is accessible. A ice cream scoop was observed in the sink basin.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
|
11/07/2013 | Risk Factor | |
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation
Observation: Sliced, portioned deli cheeses, prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (corrected on site) (repeated violation)
Observation: The food-contact equipment surfaces of the slicer and several knives in the knife rack are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink located behind the bar is not maintained so that it is accessible at all times for employee use. Basin observed with a basket inside.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Critical: Poisonous or Toxic Materials/Common Name/Working Containers (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
07/26/2013 | Risk Factor | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Raw shell eggs observed stored over ready-to-eat foods in True glass upright.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Food Storage/Preventing Contamination from the Premises
Observation: Food observed stored on floor in walk-in.
Correction: Store food where it is not exposed to splash, dust, or other contamination and/or install an approved, durable and cleanable barrier between the splash source and the food to prevent contamination.
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site)
Observation: Chili observed hot holding at 118F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Milk in bar reach-in observed at 50F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Beverage Tubing, Separation
Observation: Beverage tubing and a cold-plate beverage cooling device are in contact with ice used for drinks.
Correction: Except for cold plates that are constructed integrally with an ice storage bin, beverage tubing and cold-plate beverage cooling devices may not be installed in contact with stored ice. Beverage tubing and coldplate cooling devices may result in contamination if they are installed in direct contact with stored ice. Beverage tubing installed in contact with ice may result in condensate and drippage contaminating the ice as the condensate moves down the beverage tubing and ends up in the ice. The presence of beverage tubing and/or coldplate cooling devices also presents cleaning problems. It may be difficult to adequately clean the ice bin if they are present. Because of the high moisture environment, mold and algae may form on the surface of the ice bins and any tubing or equipment stored in the bins.
- Equipment/Good Repair and Proper Adjustment
Observation: Bar reach-in observed at 45F and is not capable of maintaining foods at 41F or below.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (corrected on site)
Observation: Spoons were stored in dirty container with pens, markers, and scissors.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Critical: Sanitized/Hot Water and Chemical/Methods (repeated violation)
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in a chemical manual or mechanical operations, using a proper solution. Dish machine is not sanitizing.
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in chemical manual or mechanical operations, including the application of sanitizing chemicals by immersion, manual swabbing, brushing, or pressure spraying methods, using a solution as specified under section 4-501.114 by providing: (1) An exposure time of at least 10 seconds for a chlorine solution specified under paragraph 4-501.114(A), (2) An exposure time of at least 7 seconds for a chlorine solution of 50 mg/L that has a pH of 10 or less and a temperature of at least 38°C (100°F) or a pH of 8 or less and a temperature of at least 24°C (75°F), (3) An exposure time of at least 30 seconds for other chemical sanitizing solutions, or (4) An exposure time used in relationship with a combination of temperature, concentration, and pH that, when evaluated for efficacy, yields sanitization as defined in Subparagraph 1-201.10(B). Efficacious sanitization depends on warewashing being conducted within certain parameters. Time is a parameter applicable to both chemical and hot water sanitization. The time hot water or chemicals contact utensils or food-contact surfaces must be sufficient to destroy pathogens that may remain on surfaces after cleaning. Other parameters, such as rinse pressure, temperature, and chemical concentration are used in combination with time to achieve sanitization.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Trays observed stored on the floor.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located in the kitchen is not maintained so that it is accessible at all times for employee use. Fruit observed in sink.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Light Bulbs, Protective Shielding
Observation: The light bulbs in the rear kitchen area are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Outer Openings, Protected
Observation: Gap observed along bottom threshold of rear exit door.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Intensity/Lighting
Observation: Light is out in True three door upright.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Physical Facilities/Repairing
Observation: The following observed in poor repair:
- walls to basement
- hole observed in wall under expo window
- wall above microwave
- floor of walk-in.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Closing Toilet Room Doors (corrected on site)
Observation: Women's restroom door was propped open.
Correction: Toilet room doors as specified under section 6-202.14 shall be kept closed except during cleaning and maintenance operations. Toilet room doors must remain closed except during cleaning operations to prevent insect and rodent entrance and the associated potential for the spread of disease.
- Critical: Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
02/22/2013 | Routine | |
Restaurant representatives - add corrected or new information about Freddie's, 555 S. 23rd St, Arlington, VA 22202-2517 »