- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: Employee observed drinking from an uncovered container in the food preparation area.
Correction: Employees may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands (2) The container and (3) Exposed food clean equipment, utensils, and linens and unwrapped single-service and single-use articles.
- Equipment/Good Repair and Proper Adjustment
Observation: The paper towel dispensing unit in the bread cutting area was observed damaged and in need of repair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces
Observation: The bread area cutting board was observed heavily scratched, scoured, and in need of replacement.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Good Repair and Calibration
Observation: One of the stem food temperature thermometers was observed not properly calibrated.
Correction: Food temperature measuring devices shall be calibrated in accordance with manufacturer's specifications as necessary to ensure their accuracy. A utensil or food temperature measuring device can act as a source of contamination to the food it contacts if it is not maintained in good repair. Also, if temperature or pressure measuring devices are not maintained in good repair, the accuracy of the readings is questionable. Consequently, a temperature problem may not be detected, or conversely, a corrective action may be needlessly taken.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: Exterior surfaces of the 3-compartment sink grease trap were observed in need of cleaning.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Surfaces of the bulk ice machine chute were observed in need of cleaning and sanitizing.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Plumbing System/Maintained in Good Repair
Observation: One of the rest-rooms was observed out of order (a repair request has been submitted).
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Liquid Wastes and Rainwater/Nonsewage
Observation: Ice build up was observed in the 3-door reach-in freezer (condensate line not properly draining).
Correction: Condensate drainage and other nonsewage liquids and rainwater shall be drained from point of discharge to disposal according to law. Liquid food wastes and rainwater can provide a source of bacterial contamination and support populations of pests. Proper storage and disposal of wastes and drainage of rainwater eliminate these conditions.
- Hand Drying Provision (corrected on site)
Observation: Disposable paper towels observed not properly provided at the back kitchen area handsink.
Correction: Each handwashing sink or group of adjacent handwashing sinks shall be provided with: (A) Individual, disposable towels
- Physical Facilities/Repairing (repeated violation)
Observation: Several floor tiles in the back kitchen area were observed cracked and damaged. The floor tile grout in the back kitchen area was observed in need of repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests
Observation: Several fruit flies observed throughout the back kitchen area.
Correction: The premises shall be maintained free of insects, rodents, and other pests. The presence of insects, rodents, and other pests shall be controlled to eliminate their presence on the premises by eliminating harborage conditions.
- Maintaining Premises, Unnecessary Items and Litter
Observation: Unnecessary items observed in need of removal from the power panel breaker room located in the back of the kitchen.
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floor/wall surfaces under and around equipment throughout the facility were observed in need of detail cleaning. The floor, drain, wall, and piping in the warewashing area was observed in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Sanitizers, Criteria/Chemicals for Food Contact Surfaces (corrected on site)
Observation: The quaternary ammonium sanitizer solution in the wiping cloth bucket was observed at a concentration greater than 400 parts per million.
Correction: Chemical sanitizers and other chemical antimicrobials applied to food-contact surfaces shall meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions). Chemical sanitizers are included with poisonous or toxic materials because they may be toxic if not used in accordance with requirements listed in the Code of Federal Regulations (CFR). Large concentrations of sanitizer in excess of the CFR requirements can be harmful because residues of the materials remain. The CFR reference that is provided lists concentrations of sanitizers that are considered safe.
- Licenses for Food Establishments
Observation: The food establishment does not have a valid license. The 2016 health license renewal application and fees have not been received.
Correction: No person shall operate a food establishment who does not have a valid license issued to him by the county manager. Only a person who complies with the requirements of this chapter shall be entitled to receive or retain such a license. Licenses are not transferable.
|
01/05/2016 | Routine | |
A work order was submitted for the 3-door preparation unit on 01/06/15. During the time of inspection the refrigeration technician arrived and was in the process of servicing/repairing the unit. Refrigeration equipment must cold hold at 41 F or below. If the refrigeration unit is unable to hold proper temperature then do not store TCS food product in the unit and/or have the unit replaced. Post 2015 Health License in public's view.
- Wiping Cloths, Use Limitation (corrected on site) (repeated violation)
Observation: Cloths in-use for wiping counters and other equipment surfaces are observed not held between uses in a chemical sanitizer solution of proper concentration.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Reheating for Hot Holding, Commercially Processed (corrected on site)
Observation: Container of shredded chicken observed not reheated to proper temperature before hot holding (117 F). Product was reheated by the person in charge.
Correction: Ready-to-eat food taken from a commercially processed, hermetically sealed container, or from an intact package from a food processing plant that is inspected by the food regulatory authority that has jurisdiction over the plant, shall be heated to a temperature of at least 57ºC (135ºF) for hot holding. Proper reheating provides a major degree of assurance that pathogens will be eliminated. The potential for growth of pathogenic bacteria is greater in reheated cooked foods than in raw foods. This is because spoilage bacteria, which inhibit the growth of pathogens by competition on raw product, are killed during cooking. Subsequent recontamination will allow pathogens to grow without competition if temperature abuse occurs.
- Cooling, Ambient Ingredients (corrected on site)
Observation: Salsa (52 F), chicken salad (54 F), pizza sausage (55 F), cheese (52 F), tuna (52 F), blue cheese (50 F) in the 3-door preparation unit observed improperly cooling. According to the manager, the product had been prepped this morning but the unit was in disrepair. The unit was observed cold holding at an ambient air temperature of around 52 F - 56 F. The TCS food product was placed on ice by the person in charge during time of inspection. The refrigeration technician also arrived at the facility during the time of inspection to service the unit.
Correction: Time/temperature control for safety food shall be cooled within 4 hours to 5ºC (41ºF) or less, if prepared from ingredients at ambient temperature, such as reconstituted foods and canned tuna. Safe cooling requires removing heat from food quickly enough to prevent microbial growth. Excessive time for cooling of time/temperature control for safety foods has been consistently identified as one of the leading contributing factors to foodborne illness. During slow cooling, time/temperature control for safety foods are subject to growth of a variety of pathogenic microorganisms. If the food is not cooled in accordance with this Code requirement, pathogens may grow to sufficient numbers to cause foodborne illness.
- Sanitizing Solutions, Testing Devices
Observation: A test kit or other device that accurately measures the concentration of the sanitizing solution is not provided.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Equipment/Good Repair and Proper Adjustment (corrected on site) (repeated violation)
Observation: The 3-door preparation unit was observed cold holding at improper temperature (52 F - 56 F). The refrigeration technician arrived on site during the time of inspection.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Cooking and Baking/Cleaning Frequency (corrected on site)
Observation: Interior of the microwave cavity observed in need of cleaning.
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: Front handsink observed being improperly used as a dump sink.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Plumbing System/Maintained in Good Repair
Observation: A leak was observed under the coffee unit station.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food in the back preparation area. A light was also observed out in the kitchen hood.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing
Observation: Floor tiles in front of the 3-compartment sink observed not maintained in good repair. A work order has been submitted.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Chemical spray bottle container(s) observed not properly labeled with the common name.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
01/07/2015 | Routine | |
- Wiping Cloths, Use Limitation (corrected on site)
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration
Correction: and/or not laundered daily.
- Cooling Methods (corrected on site)
Observation: Methods used for cooling scrambled eggs can not be accomplished with the time and temperature criteria. The scrambled eggs were observed in a closed bag and covered. The scrambled eggs were relocated to the walk in cooler and left open to cool.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: The following foods were observed cold holding at improper temperatures
Correction: 1. Pizza sauce(49ºF), cheese(48ºF), chicken(51ºF), cheese in a bag(44ºF) in the pizza prep refrigerator. 2. Top: hummus(44-46ºF) and sliced tomatoes(45ºF) in the right sandwich prep. 3. Sliced tomatoes(49ºF) and salsa(49ºF) in the 2 door salad prep refrigerator. [All refrigerators were adjusted and some foods were iced down or relocated].
- Equipment/Good Repair and Proper Adjustment (corrected on site) (repeated violation)
Observation: A few of the prep refrigerators are not maintained at 41ºF or below. Refrigerators were adjusted to 37-38ºF.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency
Observation: Surfaces of the dipping well are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
- Cleaning, Frequency and Restrictions
Observation: The surfaces under and behind shelving and equipment are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material (windex in the spray bottle).
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
01/07/2014 | Routine | |
The grease trap has been replaced.
Wash hands frequently
Handwashing sinks for handwashing only.
Cover foods in the prep refrigerators during the low periods.
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Food preparation and dispensing utensils are improperly stored. Utensils observed stored in sanitizer buckets.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Salmon individually wrapped in foil in the prep refrigerator at 75ºF was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Chicken(49ºF) and tomatoes(49ºF) cold holding at improper temperatures in the 2 door salad prep refrigerator.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Temperature Measuring Devices (corrected on site) (repeated violation)
Observation: A few prep refrigerators are not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surface of the dry storage shelf next the handsink is not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located near the bread oven is not maintained so that it is accessible at all times for employee use. Utensils observed in the basin of the handsink.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
|
02/26/2013 | Routine | |
Restaurant representatives - add corrected or new information about Cosi #175, 2011 Crystal Dr 100, Arlington, VA 22202 »