- Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Observed food employee contacting exposed RTE food (sandwiches) with bare hands. Corrected by instruction.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- In-Use Utensils, Between-Use Storage
Observation: Food preparation and dispensing utensils are improperly stored. Observed knives stored between counter and refrigerator which is soiled.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Cooling, Cooked Food (corrected on site)
Observation: Rice and chicken vegetable stew was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less. Food was discarded.
- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Foods prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Food Temperature Measuring Devices (repeated violation)
Observation: A food temperature measuring device is not provided and readily accessible for use in ensuring attainment and maintenance of food temperatures.
Correction: Food temperature measuring devices shall be provided and readily accessible for use in ensuring attainment and maintenance of food temperatures as specified under Chapter 3. The presence and accessibility of food temperature measuring devices is critical to the effective monitoring of food temperatures. Proper use of such devices provides the operator or person in charge with important information with which to determine if temperatures should be adjusted or if foods should be discarded.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surfaces of the following equipment is not kept free of an accumulation of dust, dirt, food residue, and/or other debris:
1. keg cooler
2. shelving in the walk-in cooler
3. equipment on cookline (stove, oven, fryer)
4. trash cans
5. cart.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the inside of the ice machine are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Plumbing System/Maintained in Good Repair
Observation: The cold water faucet on the hand washing sink in Bistro kitchen is not in operating.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Floors, Walls, and Ceilings/Cleanability (repeated violation)
Observation: The acoustic ceiling tiles in the kitchen (Bistro) are not designed, constructed, and installed so that it is smooth and easily cleanable.
Correction: Floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed and installed so that they are smooth and easily cleanable except for anti-slip floor coverings or applications that may be used for safety reasons and except as specified under section 6-201.14. Floors that are of smooth, durable construction and that are nonabsorbent are more easily cleaned. Requirements and restrictions regarding floor coverings, utility lines, and floor/wall junctures are intended to ensure that regular and effective cleaning is possible and that insect and rodent harborage is minimized.
- Handwashing Cleanser, Availability
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink (deli).
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
- Physical Facilities/Repairing (repeated violation)
Observation: The walls are not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors and walls are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Cleaning of Plumbing Fixtures (repeated violation)
Observation: Observed toilet and urinal plumbing fixtures (men's rest room) and handwashing sink in kitchen (Bistro) not clean and/or maintained.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
- Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material (spray bottles).
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Food Manager Certificate and Responsibility (corrected on site)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager. Certified Food Manager arrived at the end of the inspection.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
04/01/2016 | Routine | |
- Cooling, Cooked Food (corrected on site)
Observation: Observed rice cooked last night in 1/dr unit at Bistro 29 at 49 F. Rice was not cooled to 41 F W/I 6 hours. Discarded.
Correction: Cooked time/temperature control for safety food shall be cooled: (1) Within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
- Equipment/Cooking and Baking/Cleaning Frequency (corrected on site) (repeated violation)
Observation: The cavity and door seal of microwave ovens in Bistro 29 are not clean.
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Handwashing Cleanser, Availability (corrected on site)
Observation: Soap was not available in rest-room.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers used for storing poisonous or toxic materials are not identified with common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
11/04/2015 | Risk Factor | |
Please cool foods properly: Ice bath, shallow pans, walk-in storage uncovered. Cooling methods information sheet given to PIC.
- Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Observed raw chicken over noodles and other cooked foods in True one door reach in at Bistro 29.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Cooling, Cooked Food (corrected on site)
Observation: Gyro meat was not cooled within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less. Corrected by discarding.
Correction: Cooked time/temperature control for safety food shall be cooled: (1) Within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site) (repeated violation)
Observation: Noodles, rice, gyro meat, beans, and other cooked and prepared foods held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The food-contact surfaces of knives and plates stored as clean are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the ice machine are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Cooking and Baking/Cleaning Frequency (corrected on site) (repeated violation)
Observation: The cavity and door seal of the microwave ovens in both establishments are not cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure..
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located in Billy's Cheesteaks is not maintained so that it is accessible at all times for employee use. Observed chemical storage, rinsing of wiping cloth and scrubbers to clean equipment.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Handwashing Cleanser, Availability (corrected on site)
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
- Cleaning of Plumbing Fixtures (repeated violation)
Observation: Plumbing fixtures are not clean and/or maintained at the handwashing sink in between the two establishments.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
08/06/2015 | Risk Factor | |
- Food Contact with Equipment and Utensils/Preventing Contamination (corrected on site)
Observation: Food in contact with soiled equipment or utensils.Observed loaf of bread in direct contact with shelving in walk-in, and several dried goods had bowls, and paper cups inside as scoops.
Correction: Food shall only contact surfaces of: (A) Equipment and utensils that are cleaned as specified under Part 4-6 of this Code and sanitized as specified under Part 4-7 of this Code
- Gloves, Use Limitation
Observation: Single-use gloves used for more than one task, are damaged, soiled, or saved for re-use. Observed employee handling money and not changing gloves or washing hands before engaging in food prep.
Correction: If used, single-use gloves shall be used for only one task such as working with ready-to-eat food or with raw animal food, used for no other purpose, and discarded when damaged or soiled, or when interruptions occur in the operation. Soiled gloves can directly contaminate food if stored with ready-to-eat food or may indirectly contaminate food if stored with articles that will be used in contact with food.
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Observed cheese sauce hot holding at the improper temperature of 121F. Reheated
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Several cooked items in walk in and in prep units prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: The food establishment serves or sells raw or undercooked food and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Equipment, Food-Contact Surfaces, and Utensils (repeated violation)
Observation: The food-contact surfaces of two stand alone cutting boards are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment/Cooking and Baking/Cleaning Frequency (corrected on site) (repeated violation)
Observation: The cavity and door seals of the microwave ovens are not cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure..
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 10 foot candles in the walk-in freezer.
Correction: The light intensity shall be at least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in the walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning. Properly distributed light makes the need for cleaning apparent by making accumulations of soil conspicuous.
- Physical Facilities/Repairing (repeated violation)
Observation: Holes observed in wall by mop sink, some floor tiles are in poor repair near mop sink as well as some ceiling tiles are damaged or missing.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The walls and floors are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: Exhaust vents in all of the rest-rooms are in need of cleaning.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
|
02/11/2015 | Routine | |
- Critical: Food Contact with Equipment and Utensils/Preventing Contamination (corrected on site)
Observation: Food in contact with soiled equipment or utensils. Loaf of bread was in direct contact with shelving in walk in.
Correction: Food shall only contact surfaces of: (A) Equipment and utensils that are cleaned as specified under Part 4-6 of this Code and sanitized as specified under Part 4-7 of this Code
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site)
Observation: Tray of deli cheese was marked for 15 days use. Tray of sliced deli ham was marked for 10 days use. Corrected by instruction.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: The food establishment serves or sells raw or undercooked food and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. No consumer advisory on Billy's Cheesesteak side for breakfast menu. Also, no reminder asterisks on menu board for eggs served undercooked.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink at cookline in Billy's Cheesesteaks is used for purposes other than handwashing. Hand sink was being used to wash wiping cloth. Corrected by instruction.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Critical: Food Manager Certificate and Responsibility
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager. CFM card has become expired.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
10/21/2014 | Risk Factor | |
Joint inspection w/ K.B. K.P. leading
- Demonstration/Knowledge/Responding Correctly to the Inspector's Questions (corrected on site)
Observation: The person in charge did not demonstrate their knowledge of the required food temperatures and times for the safe cooking of time/temperature control for safety foods including meat, poultry, eggs, and fish.
Correction: Based on the risks inherent to the food operation, during inspections and upon request the person in charge shall demonstrate to the regulatory authority knowledge of foodborne disease prevention, application of the hazard analysis and critical control point principles, and the requirements of this Code. The person in charge shall demonstrate this knowledge by responding correctly to the inspector's questions as they relate to the specific food operation. The areas of knowledge include stating the required food temperatures and times for the safe cooking of time/temperature control for safety foods including meat, poultry, eggs, and fish.
- Demonstration/Knowledge/Responding Correctly to the Inspector's Questions (corrected on site)
Observation: The person in charge did not demonstrate their knowledge of correct procedures for cleaning and sanitizing utensils and food-contact surfaces of equipment.
Correction: Based on the risks inherent to the food operation, during inspections and upon request the person in charge shall demonstrate to the regulatory authority knowledge of foodborne disease prevention, application of the hazard analysis and critical control point principles, and the requirements of this Code. The person in charge shall demonstrate this knowledge by responding correctly to the inspector's questions as they relate to the specific food operation. The areas of knowledge include explaining correct procedures for cleaning and sanitizing utensils and food-contact surfaces of equipment.
- Critical: Responsibility of Permit Holder, Person in Charge, and Conditional Employees/Responsibilities and Reporting Symptoms and Diagnosis (corrected on site)
Observation: Certified food manager could not identify the big five foodborne illnesses.
Correction: The permit holder shall require food employees and conditional employees to report to the person in charge information about their health and activities as they relate to diseases that are transmissible through food. A food employee or conditional employee shall report the information in a manner that allows the person in charge to reduce the risk of foodborne disease transmission, including providing necessary additional information, such as the date of onset of symptoms, if the food employee or conditional employee: (1) Has any of the following symptoms: (a) Vomiting, (b) Diarrhea, (c) Jaundice, (d) Sore throat with fever, or (e) A lesion containing pus such as a boil or infected wound that is open or draining and is: (i) On the hands or wrists, unless an impermeable cover such as a finger cot or stall protects the lesion and a single-use glove is worn over the impermeable cover, (ii) On exposed portions of the arms, unless the lesion is protected by an impermeable cover, or (iii) On other parts of the body, unless the lesion is covered by a dry, durable, tight-fitting bandage
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands after handling raw chicken.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Cooling, Cooked Food
Observation: Grape leaves cooked yesterday, observed at 49F in walk-in.
Correction: Cooked time/temperature control for safety food shall be cooled: (1) Within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
- Critical: Time/Temperature Control for Safety Food, Cold Holding
Observation: Several foods observed not properly cold holding:
-pasta (42, 44F), rice (44F) egg plant (43F), and chick peas (42F) in walk-in
-gyro (43F), cheese (43F) and sliced tomatoes (42F) in two door reach-in
-lettuce (44F) in prep.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site)
Observation: Foods prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- RTE, TCS, Date Marking/Commercially Processed Food (corrected on site)
Observation: Foods prepared and packaged by a food processing plant opened and held for more than 24 hours was not clearly marked at the time the original container was opened in the food establishment to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature and time combination specified in paragraph (A) of this section and: (1) The day the original container is opened in the food establishment shall be counted as Day 1
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: Several knives observed dirty, stored as clean.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink is used for purposes other than handwashing utensils in hand sink).
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Container of soap was not labeled.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
06/27/2014 | Risk Factor | |
1. Make sure to properly cool cooked/prepared foods to 41F or less before selling or serving.
Please address all of the above by 05/02/2014. A follow-up inspection will be performed on or after 05/02/2014.
- Critical: Backflow Prevention Device, When Required
Observation: A faucet with a backflow prevetion device is not installed to preclude backflow of a solid, liquid, or gas contaminant into the water supply system at mop sink. Ice machine is also missing the same.
Correction: A plumbing system shall be installed to preclude backflow of a solid, liquid, or gas contaminant into the water supply system at each point of use at the food establishment, including on a hose bibb if a hose is attached or on a hose bibb if a hose is not attached and backflow prevention is required by law, by: (A) Providing an air gap at least twice the diameter of the water supply inlet and may not be less than 25 mm (1 inch)
- Refuse/Storage Areas, Rooms, and Receptacles, Capacity and Availability (corrected on site)
Observation: There is no waste receptacle located at the hand washing sink.
Correction: If disposable towels are used at handwashing lavatories, a waste receptacle shall be located at each lavatory or group or adjacent lavatories. Garbage containers should be available wherever garbage is generated to aid in the proper disposal of refuse.
- Refuse/Toilet Room Receptacle, Covered
Observation: There is no covered receptacle in the toilet room used by females.
Correction: A toilet room used by females shall be provided with a covered receptacle for sanitary napkins. Garbage containers should be available wherever garbage is generated to aid in the proper disposal of refuse.
- Floor and Wall Junctures, Coved, Enclosed or Sealed
Observation: Cove tiles by handwashing in storage area are not sealed to the wall. Some cove tiles are also missing by bathroom wall and prep table (slicer).
Correction: In food establishments in which cleaning methods other than water flushing are used for cleaning floors, the floor and wall junctures shall be coved and closed to no larger than 1 mm (one thirty-second inch). When cleaning is accomplished by spraying or flushing, coving and sealing of the floor/wall junctures is required to provide a surface that is conducive to water flushing.
- Outer Openings, Protected
Observation: Rear exit door is missing self-closing mechanism.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Physical Facilities/Repairing (repeated violation)
Observation: Holes observed in the wall by mop sink, in bathroom wall and behind ice machine
Correction: some floor tiles are missing by mop sink
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: Exhaust in bathroom is in need of cleaning.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
|
04/23/2014 | Other | |
Billy's Cheesesteak is still closed due to the fire from 1/13/14. The owner/manager states that their Architect is submitting plans to the county within a day.
Old dough trays are stored behind the walk-in refrigerator. The back gutter behind Pasha Cafe is full of leaves and is missing a down-spout.
Use a cutting board mat under the cutting board to keep it from slipping instead of a cloth.
- Food Storage/Preventing Contamination from the Premises
Observation: Food stored in a location where it is subject to splash, dust or other contamination (on the floor in the walk-in's).
Correction: Store food where it is not exposed to splash, dust, or other contamination and/or install an approved, durable and cleanable barrier between the splash source and the food to prevent contamination.
- Time as a Public Health Control
Observation: No written procedures exist for the use of time only as a public health control for a working supply of butter, garlic in oil, and garlic & spices in oil. A blank time as a public health control written procedure was left with the facility.
Correction: If time only is used as the public health control for a working supply of time/temperature control for safety food before cooking, or for ready-to-eat time/temperature control for safety food that is displayed or held for service for immediate consumption: (1) Written procedures shall be prepared in advance, maintained in the food establishment and made available to the regulatory authority upon request that specify: (a) Methods of compliance with Subparagraphs (B) (1)-(3) or (C) (1)-(5) of this section
- Food Temperature Measuring Devices
Observation: A food temperature measuring device is not provided and readily accessible for use in ensuring attainment and maintenance of food temperatures.
Correction: Food temperature measuring devices shall be provided and readily accessible for use in ensuring attainment and maintenance of food temperatures as specified under Chapter 3. The presence and accessibility of food temperature measuring devices is critical to the effective monitoring of food temperatures. Proper use of such devices provides the operator or person in charge with important information with which to determine if temperatures should be adjusted or if foods should be discarded.
- Equipment/Good Repair and Proper Adjustment
Observation: The rusty shelving in the walk-in refrigerator is not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The cutting boards are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment/Cooking and Baking/Cleaning Frequency
Observation: The cavity and/or door seal of the microwave ovens are not cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure..
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surfaces of the undercounter refrigerator door gaskets and shelving, the walk-in refrigerator fan cover and door flaps, inside the oven, the kitchen shelving and pan cart are not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located in the kitchen is not maintained so that it is accessible at all times for employee use (box of plastic wrap observed on the sink).
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Plumbing System/Maintained in Good Repair
Observation: The server station handwashing sink has no hot water.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Refuse/Covering Receptacles
Observation: (REPEAT): Receptacles and/or waste handling units for refuse, recyclables, and/or returnables kept outside the food establishment are not kept covered with tight-fitting lids or doors (Shared trash and recycling dumpster doors found open
Correction: grease dumpster lid was observed opened).
- Floors, Walls, and Ceilings/Cleanability
Observation: Several kitchen ceiling tiles are not designed or constructed to be smooth and easily cleanable.
Correction: Replace the pourous ceiling tiles with ones that are smooth and more easily cleaned.
- Intensity/Lighting
Observation: The light intensity is below 10 foot candles in the walk-in freezer.
Correction: The light intensity shall be at least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in the walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning. Properly distributed light makes the need for cleaning apparent by making accumulations of soil conspicuous.
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food (several ceiling lights are burnt out in the kitchen).
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing
Observation: The walls are not maintained in good repair in some areas of the kitchen and storage area. The exterior door that leads to the outside walk-in refrigerator is not in good repair. There is deteriorated wood inside the storage shed and under the walk-in refrigerator/freezer.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions
Observation: The walls and floors are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Cleaning of Plumbing Fixtures (repeated violation)
Observation: Plumbing fixtures are not clean and/or maintained (kitchen handwashing sink).
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
|
02/19/2014 | Routine | |
Lower the temperature of the walk in during lunch rush a delivery.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Food Contact with Equipment and Utensils/Preventing Contamination (corrected on site)
Observation: Food in contact with soiled equipment or utensils. Vegetable kabobs were observed stored directly on refrigerator shelving that was not clean.
Correction: Food shall only contact surfaces of: (A) Equipment and utensils that are cleaned as specified under Part 4-6 of this Code and sanitized as specified under Part 4-7 of this Code
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site) (repeated violation)
Observation: The following foods hot holding at improper temperatures
Correction: 1. Marinara sauce(120ºF) reheated. 2. Gyro stored on the top shelf over the flat top(110ºF) was discarded.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: Pizza trays and containers were observed stored in the handsink basin.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Cleaning of Plumbing Fixtures (corrected on site)
Observation: Plumbing fixtures are not clean at the back handwashing sink.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
|
10/31/2013 | Risk Factor | |
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site)
Observation: Pizza at 125 F (re-heated).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located at the back is not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Critical: Food Manager Certificate and Responsibility
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
06/04/2013 | Risk Factor | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Raw beef observed over vegetables in one door reach-in.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Utensils and Temperature and Pressure Measuring Devices/Good Repair and Calibration
Observation: Cuisinart bowl is in poor repair (a new one was ordered).
Correction: Utensils shall be maintained in a state of repair or condition that complies with the requirements specified under Parts 4-1 and 4-2 or shall be discarded. A utensil or food temperature measuring device can act as a source of contamination to the food it contacts if it is not maintained in good repair.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood contact of the cinder blocks under ice machine, rusty shelves in walk-in and the wood block under the ice well are not smooth and easily cleanable.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Plumbing System/Maintained in Good Repair
Observation: Pipes observed leaking in room with water heater (deli side) by dryer.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Refuse/Covering Receptacles
Observation: Grease tank lid observed open.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
- Refuse/Maintaining Refuse Areas and Enclosures
Observation: Grease observed on ground by grease tank.
Correction: A storage area and enclosure for refuse, recyclables, or returnables shall be maintained free of unnecessary items, as specified under section 6-501.114, and clean. Proper storage and disposal of garbage and refuse are necessary to minimize the development of odors, prevent such waste from becoming an attractant and harborage or breeding place for insects and rodents, and prevent the soiling of food preparation and food service areas. Improperly handled garbage creates nuisance conditions, makes housekeeping difficult, and may be a possible source of contamination of food, equipment, and utensils.
- Floors, Walls, and Ceilings/Cleanability (repeated violation)
Observation: Wall behind the ice well in the bar area is not designed to stand up to moisture.
Correction: Floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed and installed so that they are smooth and easily cleanable except for anti-slip floor coverings or applications that may be used for safety reasons and except as specified under section 6-201.14. Floors that are of smooth, durable construction and that are nonabsorbent are more easily cleaned. Requirements and restrictions regarding floor coverings, utility lines, and floor/wall junctures are intended to ensure that regular and effective cleaning is possible and that insect and rodent harborage is minimized.
- Floor Covering, Mats and Duckboards/Cleanable
Observation: Carpet observed in kitchen.
Correction: Mats and duckboards shall be designed to be removable and easily cleanable. Requirements regarding mats and duckboards are intended to ensure that regular and effective cleaning is possible and that accumulation of dirt and waste is prevented.
- Light Bulbs, Protective Shielding
Observation: The light bulbs above the ice machine is not shielded or plastic coated
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Physical Facilities/Repairing (repeated violation)
Observation: The following observed in need of repair:
- wall by clothes washer
- wall behind ice well at the bar area
- ceiling over mop sink.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests (repeated violation)
Observation: Rat burrows observed on back side of shed.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by routinely inspecting the premises for evidence of pests. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
|
02/27/2013 | Follow-up | |
1. the 2013 permit from the health department was not observed to be posted during inspection.
2. one or two light bulbs were out in the establishment. The light was out in the walk-in freezer. The light was out in the outdoor storage shed.
3. A dirty pizza cutter and some dirty knives were observed on the wall magnets during inspection. They were taken down to be cleaned during inspection.
4. Some wet stacking was observed during the inspection.
5. The shelves by the bar were observed to be in need of re-sealing.
6. The mop sink was observed to be leaking.
7. The light bulb over the mop sink was not shielded and did not look to be shatter resistant.
8. An pitcher was observed in the ice machine being used as a scoop with the handle touching the ice. This was removed during the inspection.
9. On the deli side, flour was observed stored on the floor in a container that was in poor repair and lacked a label.
- Critical: Demonstration/Knowledge/Responding Correctly to the Inspector's Questions (corrected on site)
Observation: The CFM did not demonstrate knowledge of the big 5 foodborne illnesses.
Correction: Based on the risks inherent to the food operation, during inspections and upon request the person in charge shall demonstrate to the regulatory authority knowledge of foodborne disease prevention, application of the hazard analysis and critical control point principles, and the requirements of this Code. The person in charge shall demonstrate this knowledge by responding correctly to the inspector's questions as they relate to the specific food operation. The areas of knowledge include explaining the responsibilities, rights, and authorities assigned by this Code to the: (a) Food employee, (b) Conditional employee, (c) Person in charge, (d) Regulatory Authority.
- Critical: Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site) (repeated violation)
Observation: An open beverage container was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Salmon observed over sauce. Ground meat observed over sauce.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination
Observation: Food is not in packages, covered containers, or wrappings. Walnus, almonds and flour were observed left uncovered in the main kitchen.
Correction: Food shall be protected from cross contamination by storing the food in packages, covered containers, or wrappings. This section does not apply to: (1) Whole, uncut, raw fruits and vegetables and nuts in the shell, that require peeling or hulling before consumption
- Food Storage/Preventing Contamination from the Premises
Observation: Stored food is not protected from contamination. There was oil and salt observed stored in the outdoor storage shed. Panko bread crumbs were observed stored in the floor.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Garlic in oil was observed at 72F not in any units in the main kitchen. The garlic in oil was discarded during inspection. Tomato soup (49F) and sauce (49F) were observed at the indicated improper temperature in the WIC.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Nonfood-Contact Surfaces/Nonabsorbent (repeated violation)
Observation: The nonfood-contact surface of the cinder blocks under the ice machine, the rusty shelves in the refrigerator, and the wood block under the ice well are not smooths and easily cleanable.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Critical: Food-Contact Surfaces/Cleanability
Observation: The food-contact surface of theold spatulas and the bowl of the cuisanrt were not observed to be smooth, free of breaks, open seams, cracks, chips, inclusions, pits, similar imperfections, finished to have smooth welds and joints, and/or accessible for cleaning and inspection by an approved method.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Temperature Measuring Devices
Observation: Two refrigeration units were observed with out a working thermometer inside.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Fixed, Spacing or Sealing
Observation: The chemical equipment near the water heater that is not easily movable is not installed to allow access for cleaning. The main kitchen handwashing sink, prep sink, and 2-part sink were observed to not be well sealed to the wall.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surface of the top of the pizza oven top, the warewashing machine, , the insides of two of the microwaves, and the open kitchen shelves are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency
Observation: Some mold was observed in the main ice machine and in the ice well behind the bar.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
- Equip/Utensils/Linens/Single-Service/Storage/Prohibitions
Observation: Cleaned and sanitized equipment, utensils, laundered linens, single-service and/or single-use articles are stored on the floor of an outdoor shed that is not sealed to the outside.
Correction: Cleaned and sanitized equipment, utensils, laundered linens, and single-service and single-use articles may not be stored: (1) In locker rooms
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink in the main kitchen was observed with utensils stored in the basin.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Refuse/Covering Receptacles (repeated violation)
Observation: The outside dumpsters used by the location were observed with the lids left open.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
- Floors, Walls, and Ceilings/Cleanability
Observation: The wall by the pizza oven and behind the dish machine was not designed or constructed to be smooth and easily cleanable. The hole under the handwashing sink in the main kitchen is also not easily cleanable. The wall behind the ice well in the bar area is also not designed to stand up to moisture.
Correction: Floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed and installed so that they are smooth and easily cleanable except for anti-slip floor coverings or applications that may be used for safety reasons and except as specified under section 6-201.14. Floors that are of smooth, durable construction and that are nonabsorbent are more easily cleaned. Requirements and restrictions regarding floor coverings, utility lines, and floor/wall junctures are intended to ensure that regular and effective cleaning is possible and that insect and rodent harborage is minimized.
- Outer Openings, Protected
Observation: The outer openings of the food establishment are not protected against the entry of insects and rodents. The storage shed outside has very large hole in the floor and several other gaps and holes in the structure. The rear door by the water heater was observed to not be tightly sealed of the outside and daylight was observed around the AC unit in the main kitchen. the other door in the main kitchen was also observed to not be well sealed to the outside.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Hand Drying Provision (corrected on site)
Observation: No paper towels were initially available at the handwashing sink in the main kitchen or in the men's bathroom.
Correction: Each handwashing sink or group of adjacent handwashing sinks shall be provided with: (A) Individual, disposable towels
- Handwashing Signage (repeated violation)
Observation: There was no sign observed near the handwashing sink in the deli section of the establishment.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Physical Facilities/Repairing
Observation: The outdoor storage shed and the wall behind the dish machine are not maintained in good repair. the wall behind the ice well in the bar and the ceiling over the mop sink are also in poor repair. Some cracked tiles were observed in the passage way between the two areas
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Controlling Pests
Observation: Insect, rodent, and/or other pest harborage conditions exist on the premises. Some rat dropping were observed in the outside storage shed and some rat tunnels were observed in the side of the hill neat the dumpsters.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Maintaining Premises, Unnecessary Items and Litter
Observation: The premises is not free of items that are unnecessary to the operation or maintenance of the establishment. The coffee items in the storage shed are reported to no longer be used. In addition, the old soap dispensers in the main establishment and the 2-dr glass refrigerator in the deli section is not in use nor is the 1-door upright refrigerator in the main kitchen.
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
- Cleaning, Frequency and Restrictions
Observation: The floor and walls of the main kitchen are not cleaned as often as necessary to keep them clean. Significant build up was observed under and behind equipment in the kitchen and especially near the water heater and the chemical equipment that is not easily movable.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Cleaning of Plumbing Fixtures (repeated violation)
Observation: The handwashing sink in the main kitchen was observed to be in need of cleaning.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
|
01/14/2013 | Routine | |
Mice droppings were found under the 3-part sink.
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: Diced tomatoes at 55 F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
|
08/24/2011 | Risk Factor Assessment | |
Restaurant representatives - add corrected or new information about Bistro 29 & Billy's Cheesesteaks, 3907 & 3911 Lee Hwy, Arlington, VA 22207 »