- Reheating for Hot Holding, Commercially Processed (corrected on site)
Observation: Ready-to-eat marinara sauce found at 84 F was not heated to a sufficient temperature for hot holding.
Correction: Ready-to-eat food taken from a commercially processed, hermetically sealed container, or from an intact package from a food processing plant that is inspected by the food regulatory authority that has jurisdiction over the plant, shall be heated to a temperature of at least 57ºC (135ºF) for hot holding. Proper reheating provides a major degree of assurance that pathogens will be eliminated. The potential for growth of pathogenic bacteria is greater in reheated cooked foods than in raw foods. This is because spoilage bacteria, which inhibit the growth of pathogens by competition on raw product, are killed during cooking. Subsequent recontamination will allow pathogens to grow without competition if temperature abuse occurs.
- Temperature Measuring Devices (repeated violation)
Observation: The Turbo Air 2 dr bar unit is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Single-service and/or single-use articles are improperly stored. Single service items stored on shelving that is not 6 inches above floor in basement.
Correction: Single-service and single-use articles shall be stored as specified under section (A) of this section and shall be kept in the original protective package or stored by using other means that afford protection until used. Clean equipment and multiuse utensils which have been cleaned and sanitized, laundered linens, and single-service and single-use articles can become contaminated before their intended use in a variety of ways such as through water leakage, pest infestation, or other insanitary condition.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing station at the bar is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees. No signage available in men's restroom.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Intensity/Lighting (repeated violation)
Observation: Some lights were burned out in kitchen.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing (repeated violation)
Observation: Some floor tiles in kitchen were missing and/or damaged in various areas of the kitchen.
Hole was observed in wall above urinal in men's restroom.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
|
06/22/2015 | Routine | |
- In-Use Utensils, Between-Use Storage (repeated violation)
Observation: Ice cream scoop in standing water.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Wiping Cloths, Use Limitation
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Observed foods cold holding on ice at improper temperatures (cut leafy greens 54 F, cut tomatoes 48 F, cheese 50 F). Foods were discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment/Good Repair and Proper Adjustment
Observation: The gaskets on the 2 door prep are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
The wooden shelving above prep are is no longer smooth, easily cleanable.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces
Observation: The surfaces of the cutting board on the prep unit are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surfaces of the equipment in the kitchen are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: Utensils stored as clean were not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the inside of the ice machine are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment and Utensils, Air-Drying Required
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried or adequately drained before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Cleaned equipment and utensils were observed in soiled bins and shelving in the dish washing area.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station in the kitchen is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Light Bulbs, Protective Shielding (repeated violation)
Observation: The light bulbs in the kitchen in dish washing room are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 50 foot candles where food employees are working with food.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing (repeated violation)
Observation: The floors and walls are not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions
Observation: The floors, walls, and ceilings are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Cleaning of Plumbing Fixtures
Observation: Plumbing fixtures are not clean and/or maintained. The handwashing sink at the bar and the urinals in the men's rest-room are in need of cleaning.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers (spray bottles) used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
07/01/2014 | Routine | |
Joint inspection w/EC observing.
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Ice cream scoop was improperly stored in standing water at room temperature (81F).
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Temperature Measuring Devices (corrected on site)
Observation: Turbo air" bar 2-door counter refrigerator is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Manual Warewashing/Sink Compartment Requirements (corrected on site)
Observation: Three (3)-compartment sink does not have 3 drain plugs.
Correction: Except as specified in paragraph (C) of this section, a sink with at least 3 compartments shall be provided for manually washing, rinsing, and sanitizing equipment and utensils. The 3 compartment sink requirement allows for proper execution of the 3-step manual warewashing procedure. If properly used, the 3 compartments reduce the chance of contaminating the sanitizing water and therefore diluting the strength and efficacy of the chemical sanitizer that may be used. Alternative manual warewashing equipment, allowed under certain circumstances and conditions, must provide for accomplishment of the same 3 steps: 1. Application of cleaners and the removal of soil
- Light Bulbs, Protective Shielding
Observation: Some light bulbs in the kitchen have broken shields and others are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Intensity/Lighting
Observation: The light intensity is below 10 foot candles in the walk-in refrigerator.
Correction: The light intensity shall be at least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in the walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning. Properly distributed light makes the need for cleaning apparent by making accumulations of soil conspicuous.
- Intensity/Lighting
Observation: The light intensity is below 20 foot candles at the bar.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food in kitchen.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing
Observation: 1. Missing and crack tiles in warewashing area
Correction: floor needs regrouting.
2. Some ceiling tiles are missing in warewashing area.
- Critical: Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
06/25/2013 | Routine | |
Restaurant representatives - add corrected or new information about Arlington Cinema 'n' Drafthouse, 2903 Columbia Pike, Arlington, VA 22204 »