- Food Storage Containers, Identified with Common Name of Food (repeated violation)
Observation: Containers of flour, sugar and salt are not identified with the common name of the food.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- In-Use Utensils, Between-Use Storage (repeated violation)
Observation: Food preparation and dispensing utensils are improperly stored. The flour bin scoop handle has broken off and cups instead of scoops with handles were observed in the sugar and salt bins.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Temperature Measuring Devices
Observation: The sandwich prep refrigerator is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The cabinetry under the soda fountain machine is not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (repeated violation)
Observation: Surfaces of the soda fountain drink nozzles and can opener blade are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surfaces of the sandwich prep refrigerator and walk-in refrigerator shelves and the prep table lower shelf are not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Equip/Utensils/Linens/Single-Service/Storage/Prohibitions (repeated violation)
Observation: Single-service and/or single-use articles are stored outside/behind the building.
Correction: Cleaned and sanitized equipment, utensils, laundered linens, and single-service and single-use articles may not be stored: (1) In locker rooms
- Plumbing System/Maintained in Good Repair (repeated violation)
Observation: The three part sink spray hose tubing is exposed.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Refuse/Toilet Room Receptacle, Covered
Observation: There is no covered receptacle in the toilet room.
Correction: A toilet room used by females shall be provided with a covered receptacle for sanitary napkins. Garbage containers should be available wherever garbage is generated to aid in the proper disposal of refuse.
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees (rest-room).
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Poisonous or Toxic Materials/Common Name/Working Containers (repeated violation)
Observation: A working container of bleach is not identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Permit to Operate/Responsibilities of Permit Holder (repeated violation)
Observation: The permit is not posted in a location in the food establishment that is conspicuous to consumers.
Correction: Upon acceptance of the permit issued by the regulatory authority, the permit holder in order to retain the permit shall post the permit in a location in the food establishment that is conspicuous to consumers.
|
03/03/2016 | Routine | |
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Surfaces of the can opener blade are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Poisonous or Toxic Materials/Restrictions/Presence and Use (corrected on site)
Observation: Raid Ant and Roach spray and Raid Roach spray are not required for the operation and maintenance of the food establishment. Removed.
Correction: Only those poisonous or toxic materials that are required for the operation and maintenance of the establishment, such as for the cleaning and sanitizing of equipment and utensils and the control of insects and rodents, shall be allowed in the food establishment. This section does not apply to packaged poisonous or toxic materials that are for retail sale. The presence in the establishment of poisonous or toxic materials that are not required for the maintenance and operation of the establishment represents an unnecessary risk to both employees and consumers. Preserving food safety depends in part on the appropriate and proper storage and use of poisonous or toxic materials that are necessary to the maintenance and operation of a food establishment. Even those that are necessary can pose a hazard if they are used in a manner that contradicts the intended use of the material as described by the manufacturer on the material's label. If additional poisonous or toxic materials are present, there is an unwarranted increased potential for contamination due to improper storage (e.g., overhead spillage that could result in the contamination of food, food-contact surfaces, or food equipment) or inappropriate application.
|
09/10/2014 | Risk Factor | |
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Surfaces of the drink fountain nozzles are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Cleanser, Availability (corrected on site)
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at handwashing sink in restroom.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap.
|
05/27/2014 | Risk Factor | |
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Clean and sanitized are improperly stored between 3-compartment sink and wall.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Marinara sauce (98F) and meatballs (128F) were observed at improper hot holding temperature on steamtable.
Correction: (reheated) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Noodles prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Plumbing System/Maintained in Good Repair
Observation: Spray hose on 3-compartment sink is not maintained good repair.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
|
01/13/2014 | Routine | |
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Sausage (49F), Pepperoni (49F) and Ham (49F) were observed at improper cold holding temperature in "True" 2-dr pizza prep refrigerator.
Correction: (relocated to WIC) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation
Observation: Noodles prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Critical: Time as a Public Health Control (repeated violation)
Observation: No written procedures exist for the use of time only as a public health control for a working supply of pizzas.
Correction: If time only is used as the public health control for a working supply of potentially hazardous food (time/temperature control for safety food) before cooking, or for ready-to-eat potentially hazardous food (time/temperature control for safety food) that is displayed or held for service for immediate consumption: (1) Written procedures shall be prepared in advance, maintained in the food establishment and made available to the regulatory authority upon request that specify: (a) Methods of compliance with Subparagraphs (B) (1)-(3) or (C) (1)-(5) of this section
- Equipment/Good Repair and Proper Adjustment
Observation: The "True" 2-door pizza prep and "Bally" walk-in refrigerator (freezing up) are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Plumbing System/Maintained in Good Repair
Observation: Spray hose on 3-compartment sink is not maintained good repair.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Outer Openings, Protected
Observation: The outer openings of the food establishment are not protected against the entry of insects and rodents. Back exit door was propped open.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
|
09/27/2013 | Routine | |
- Critical: Hands and Arms/When to Wash (repeated violation)
Observation: A food employee failed to wash his or her hands before engaging in food preparation after touching bare human body parts.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Eating, Drinking, or Using Tobacco/Food Contamination Prevention
Observation: An open beverage container and/or a closed beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Critical: Eating, Drinking, or Using Tobacco/Food Contamination Prevention
Observation: 2 employees were observed drinking from an uncovered container in the food preparation area.
Correction: Employees may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands (2) The container and (3) Exposed food clean equipment, utensils, and linens and unwrapped single-service and single-use articles.
- Critical: Contamination from Hands/Preventing Contamination by Employees
Observation: Employees observed contacting ready-to-eat (RTE) food with their bare hands. Touching ready to eat pizza with cutting it with a pizza cutter and holding the pizza with bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph (D) of this section, food employees may not contact exposed, RTE food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Critical: Food Contact with Equipment and Utensils/Preventing Contamination (repeated violation)
Observation: Bowl observed laying on top of ready to eat food (cheese) in the pizza prep refrigerator.
Correction: Food shall only contact surfaces of: (A) Equipment and utensils that are cleaned as specified under Part 4-6 of this Code and sanitized as specified under Part 4-7 of this Code
- Wiping Cloths, Use Limitation (repeated violation)
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration
Correction: and/or not laundered daily.
- Food Storage/Preventing Contamination from the Premises
Observation: Containers with oil observed stored outside and on the ground.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Critical: Potentially Hazardous Food, Hot Holding (repeated violation)
Observation: Pizza observed hot holding at the improper temperature of 89F and 100F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation (repeated violation)
Observation: Noodles in bags, chicken and various vegetables, prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Critical: Time as a Public Health Control
Observation: No written procedures exist for the use of time only as a public health control for a working supply of pizza.
Correction: If time only is used as the public health control for a working supply of potentially hazardous food (time/temperature control for safety food) before cooking, or for ready-to-eat potentially hazardous food (time/temperature control for safety food) that is displayed or held for service for immediate consumption: (1) Written procedures shall be prepared in advance, maintained in the food establishment and made available to the regulatory authority upon request that specify: (a) Methods of compliance with Subparagraphs (B) (1)-(3) or (C) (1)-(5) of this section
- Nonfood-Contact Surfaces (repeated violation)
Observation: The nonfood-contact surface of the soda crates used as shelving is not free of unnecessary ledges, projections, and crevices, and/or designed and constructed to be easily cleanable or maintained.
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The inside of the ice machine was observed very moldy.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. Employee was observed washing equipment and utensils and not sanitizing them.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Critical: Backflow Prevention Device, When Required
Observation: Observed that the pre-wash spray hose extend below the flood rim level of the sink basin at the 3-vat sink.
Correction: Alter or repair the pre-wash spray hose component to provide the necessary separation between the water supply and the flood rim level of the sink basin or install an approved backflow prevention device. The minimum allowable separation distance must be at least 2x the diameter of the water supply inlet and at least 1 inch.
- Handwashing Sink/Using/Operation and Maintenance (repeated violation)
Observation: The handwashing sink located kitchen is not maintained so that it is accessible at all times for employee use. A fan was observed laying on top of basin.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Handwashing Sink/Using/Operation and Maintenance (repeated violation)
Observation: The handwashing station at the kitchen is being used as a dump station for AC unit drain.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Outer Openings, Protected (repeated violation)
Observation: The back door of the establishment in not self closing.
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Physical Facilities/Repairing
Observation: The back is not maintained in good repair. It is very hard to close.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
|
08/31/2011 | Routine | |
Restaurant representatives - add corrected or new information about Pizza Roma, 4219 N Fairfax Dr, Arlington, VA 22203 »