End prep unit has been equipped with a new compressor. Unit operating at 37 F, with TCS foods at 41 F or less.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The 3 door line prep unit was not operating at 41 F or less.
The caulk at the 3 part sink assembly and the ware washing machine assembly were observed with accumulation of mold.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surface of the shelving for the spices, the exterior and interior of refrigeration units, and some door gaskets, are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing (repeated violation)
Observation: Cleaned equipment and utensils, laundered linens, and single-service and/or single-use articles are improperly stored. Dishracks with clean dishes, and refrigerator prep tops were stored on the floor.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floor along the cook line and the floor of the walk in freezer were in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/25/2016 | Follow-up | |
Malfunctioning prep refrigerator was not in use at time of re-inspetion except for prep top that was being used with foods submerged in ice and at 41 F or less.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The 3 door line prep unit was not operating at 41 F or less.
The caulk at the 3 part sink assembly and the ware washing machine assembly were observed with accumulation of mold.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surface of the shelving for the spices, the exterior and interior of refrigeration units, and some door gaskets, are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing (repeated violation)
Observation: Cleaned equipment and utensils, laundered linens, and single-service and/or single-use articles are improperly stored. Dishracks with clean dishes, and refrigerator prep tops were stored on the floor.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floor along the cook line and the floor of the walk in freezer were in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/23/2016 | Follow-up | |
Follow-up to be conducted on or about 10 days to determine compliance.
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Food preparation and dispensing utensils are improperly stored. Knives were stored in between prep surface and wall.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: TCS items in 3 door line prep, including milk at 48 F, goat curry at 47 F, and lamb item at 47 F. Ice added to prep top. Call for immediate service was placed.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site) (repeated violation)
Observation: Several prepared, cooked food items in walk in, prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded. Corrected by instruction.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The 3 door line prep unit was not operating at 41 F or less.
The caulk at the 3 part sink assembly and the ware washing machine assembly were observed with accumulation of mold.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surface of the shelving for the spices, the exterior and interior of refrigeration units, and some door gaskets, are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surfaces of several knives stored between wall and prep counter are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Cleaned equipment and utensils, laundered linens, and single-service and/or single-use articles are improperly stored. Dishracks with clean dishes, and refrigerator prep tops were stored on the floor.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Cleaning, Frequency and Restrictions
Observation: The floor along the cook line and the floor of the walk in freezer were in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/07/2016 | Routine | |
- Food Contact with Equipment and Utensils/Preventing Contamination (corrected on site)
Observation: Uncovered bulk spices in dry storage are subject to contamination from items stored on above racks.
Correction: Food shall only contact surfaces of: (A) Equipment and utensils that are cleaned as specified under Part 4-6 of this Code and sanitized as specified under Part 4-7 of this Code
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surfaces of the canopener blade are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station at the line was observed with a bowl in basin.
Correction: The handwashing facility identified above is to be used for washing hands only.
|
11/04/2015 | Risk Factor | |
Facility is available for catering.
Follow-up scheduled for 48 hours to ensure Kolpak 3 door prep unit is functioning at 41 F., with Temperature Control For Safety foods at 41 F or less.
- Demonstration/Knowledge/Complying with Code (corrected on site)
Observation: Violations of priority items were observed during the current inspection. CFM was aware that prep unit was malfunctioning but did not discontinue use.
Correction: Based on the risks inherent to the food operation, during inspections and upon request the person in charge shall demonstrate to the regulatory authority knowledge of foodborne disease prevention, application of the hazard analysis and critical control point principles, and the requirements of this Code. The person in charge shall demonstrate this knowledge by complying with this Code by having no violations of priority items during the current inspection.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Chicpeas at 46 F, goat was at 50 F, chicken was at 51 F, shrimp was at 52 F, milk was at 51 F, in Kolpak 3 dr prep unit. Food items were discarded. Call for service was placed.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surfaces of the can opener blade are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station at the dish washing area is being used as a dump station. Corrected by instruction.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
07/13/2015 | Risk Factor | |
- Demonstration/Knowledge/Responding Correctly to the Inspector's Questions (corrected on site)
Observation: The person in charge did not demonstrate their knowledge of symptoms associated with the diseases that are transmissible through food.
Correction: Based on the risks inherent to the food operation, during inspections and upon request the person in charge shall demonstrate to the regulatory authority knowledge of foodborne disease prevention, application of the hazard analysis and critical control point principles, and the requirements of this Code. The person in charge shall demonstrate this knowledge by responding correctly to the inspector's questions as they relate to the specific food operation. The areas of knowledge include describing the symptoms associated with the diseases that are transmissible through food.
- In-Use Utensils, Between-Use Storage (corrected on site) (repeated violation)
Observation: Food preparation and dispensing utensils are improperly stored. Rice scoop was stored in room temperature standing water.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Food Display/Preventing Contamination by Consumers
Observation: Food on display is not protected from contamination. Salad and kesari kheer were not covered on buffet.
Correction: Except for nuts in the shell and whole, raw fruits and vegetables that are intended for hulling, peeling, or washing by the consumer before consumption, food on display shall be protected from contamination by the use of packaging
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Taandori chicken was hot holding at 71 F in kitchen. Discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surface of the gaskets on prep refrigerators, exterior of refrigerators, stove tops, and sides of equipment were not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Handwashing Sink/Using/Operation and Maintenance
Observation: The handwashing sinks located at wait station and ware washing stations were not draining properly.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 50 foot candles under hood where a food employee is working with food.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Physical Facilities/Repairing
Observation: Kitchen floor tile grout is not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
|
03/04/2015 | Routine | |
- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Chick peas, lamb curry, etc., in walk in, prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The food-contact surfaces of the cutting board used for cutting chicken are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Critical: Food Manager Certificate and Responsibility
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
11/04/2014 | Risk Factor | |
Catering available through establishment.
- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Cooked spinach, chickpeas, ground cooked lamb, cooked vegetables, butter chicken, in tubs in walk in, prepared and held in the food establishment for more than 24 hours was not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Handwashing Sink/Using/Operation and Maintenance
Observation: The handwashing sink located at the far back prep area is not maintained so that it is accessible at all times for employee use. Hand sink has inadequate pressure.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Handwashing Signage (corrected on site)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees. The hand washing signage in the women's restroom has fallen off wall. Signage provided.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
07/15/2014 | Risk Factor | |
- Critical: Backflow Prevention, Air Gap (repeated violation)
Observation: The diameter of the air gap between the water supply inlet and the flood level rim of the 3 part sink is less than 1 inch.
Correction: Provide an air gap with a diameter that is at least twice the diameter of the water supply inlet and not less than 1 inch for proper backflow prevention by the air gap.
|
04/14/2014 | Follow-up | |
- Demonstration/Knowledge/Responding Correctly to the Inspector's Questions (corrected on site)
Observation: The person in charge did not demonstrate their knowledge of the required temperatures and times for the safe refrigerated storage, hot holding, cooling, and reheating of time/temperature control for safety foods.
Correction: Based on the risks inherent to the food operation, during inspections and upon request the person in charge shall demonstrate to the regulatory authority knowledge of foodborne disease prevention, application of the hazard analysis and critical control point principles, and the requirements of this Code. The person in charge shall demonstrate this knowledge by responding correctly to the inspector's questions as they relate to the specific food operation. The areas of knowledge include stating the required temperatures and times for the safe refrigerated storage, hot holding, cooling, and reheating of time/temperature control for safety foods.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Thawing
Observation: Whole chickens were thawing in standing water.
Correction: Time/temperature control for safety food shall be thawed: (A) Under refrigeration that maintains the food temperature at 5ºC (41ºF) or less
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Four large containers of cooked onion sauce, in walk in at 58-62 F, was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less. Discarded.
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Cooked onion sauce, cooked tomato sauce, prepared and held in the food establishment for more than 24 hours were not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment/Good Repair and Proper Adjustment
Observation: The caulking was in disrepair at the bar 3 part sink.
The caulking was moldy and in disrepair at the ware washing table assembly.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Critical: Backflow Prevention, Air Gap
Observation: The diameter of the air gap between the water supply inlet and the flood level rim of the 3 part sink is less than 1 inch.
Correction: Provide an air gap with a diameter that is at least twice the diameter of the water supply inlet and not less than 1 inch for proper backflow prevention by the air gap.
- Handwashing Sink/Using/Operation and Maintenance (repeated violation)
Observation: The handwashing station at the wait station is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Handwashing Signage (corrected on site)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees. No hand wash sign at ware washing hand sink. VDH signage provided.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Intensity/Lighting
Observation: A light is out under the hood.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Controlling Pests
Observation: Insect, rodent, and/or other pest harborage conditions exist on the premises. Fruit flies present at bar.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
- Critical: Food Manager Certificate and Responsibility (repeated violation)
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
03/10/2014 | Routine | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Several food containers not covered inside the walk-in cooler.
Correction: Food shall be protected from cross contamination by storing the food in packages, covered containers, or wrappings. This section does not apply to: (1) Whole, uncut, raw fruits and vegetables and nuts in the shell, that require peeling or hulling before consumption
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Lamb at 60 F, discarded. Chickpeas at 46 F, discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation
Observation: There were a lots of ready to eat food containers prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Critical: Food Manager Certificate and Responsibility
Observation: The food manager is not properly training food service personnel in sanitary food-handling techniques and proper methods of food protection.
Correction: The food manager or limited food manager shall be responsible for training food service personnel in sanitary food-handling techniques and proper methods of food protection, and for ensuring that good public health and food protection practices and sanitary techniques in manufacturing, storing, serving and transporting foods are used at all times on the premises under their control.
|
10/14/2013 | Risk Factor | |
1. Wash hands frequently.
2. Make sure to cool cooked foods properly.
3. Do not store dish racks on the floor.
4. Consider changing/replacing plastic containers/lids which are not cleanable anymore.
5. Remove dead cockroaches from light shields.
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: The following foods were observed at improper cold holding temperature:
1. Tandoori chicken (47F) and Fried paneer (46F) in walk-in refrigerator - (corrected - foods uncovered for faster cooling)
2. Tomatoes (49F) on ice - (relocated to walk-in)
3. Lamb curry (47F), Mustard (48F), Tomatoes (46F), Chickpeas (47F), Cauliflower w/potatoes (47F) in "Kairak" 3-door prep refrigerator - (foods relocated to walk-in)
4. Samosas (76F), Potato patties (77F) and Dumplings (75F) on kitchen counter - (discarded)
Correction: (CORRECTED DURING INSPECTION) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station at the cookline is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Hand Drying Provision (corrected on site)
Observation: Handwashing sink across from warewashing machine is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
|
06/15/2013 | Risk Factor | |
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Employees observed contacting ready-to-eat (RTE) food with their bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph (D) of this section, food employees may not contact exposed, RTE food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination
Observation: Several foods in prep refrigerators are not in packages, covered containers, or wrappings.
Correction: Food shall be protected from cross contamination by storing the food in packages, covered containers, or wrappings. This section does not apply to: (1) Whole, uncut, raw fruits and vegetables and nuts in the shell, that require peeling or hulling before consumption
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Food preparation and dispensing utensils are improperly stored in standing water at room temperature.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Wiping Cloths, Use Limitation
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration
Correction: and/or not laundered daily.
- Critical: Potentially Hazardous Food, Cold Holding
Observation: Chickpeas (45F), Mixed vegetables (49F), Lentils (49F), Lamb curry (49F) and Chicken curry (49F) in "Kaiak" 3-door prep refrigerator were observed at improper cold holding temperature.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 50 foot candles in kitchen where a food employee is working with food.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Controlling Pests
Observation: Insect, rodent, and/or other pest harborage conditions exist on the premises. Dead roaches observed in kitchen light shields.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by eliminating harborage conditions. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Cleaning, Frequency and Restrictions
Observation: Some stained kitchen ceiling tiles are in need of cleaning and painting.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
01/28/2013 | Routine | |
Restaurant representatives - add corrected or new information about Zaika, 2800 Clarendon Blvd R-900, Arlington, VA 22201-2844 »