- Food Storage/Preventing Contamination from the Premises
Observation: Observed food not protected from contamination due to dust and soil hanging from the ceiling directly above uncovered food in the steam table.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Reheating for Hot Holding (corrected on site)
Observation: The chili that is cooked, cooled, and reheated for hot holding was not reheated so all parts of the food reached a temperature of at least 74ºC (165ºF) for 15 seconds. Reheated to 180 F.
Correction: Time/temperature control for safety food that is cooked, cooled and reheated for hot holding shall be reheated so that all parts of the food reach a temperature of at least 74ºC (165ºF) for 15 seconds. When food is held, cooled, and reheated in a food establishment, there is an increased risk from contamination caused by personnel, equipment, procedures, or other factors. If food is held at improper temperatures for enough time, pathogens have the opportunity to multiply to dangerous numbers. Proper reheating provides a major degree of assurance that pathogens will be eliminated. The potential for growth of pathogenic bacteria is greater in reheated cooked foods than in raw foods. This is because spoilage bacteria, which inhibit the growth of pathogens by competition on raw product, are killed during cooking. Subsequent recontamination will allow pathogens to grow without competition if temperature abuse occurs.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Observed foods (turkey 52 F, mozzarella 49 F in the two door prep
Correction: corn salsa 49 F, ribs 48 F, macaroni 47 F, cut cabbage 46 F in the four door refrigerator
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surfaces of the shelving in the walk-in cooler (rusted) and dry storage shelving (chipping, peeling paint) are not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment/Good Repair and Proper Adjustment
Observation: The dairy walk-in cooler and the four door refrigerator on the cookline are is not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design. Units are not maintaining food at 41 F or below.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces
Observation: The surfaces of the cutting board at the grill are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surfaces of the equipment in the kitchen and bar areas are not kept free of an accumulation of dust, dirt, food residue, and/or other debris. The shelving in the walk-in coolers have an accumulation of food debris and mold.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: Observed stickers residue on outside and inside of food containers.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the inside of the ice machines and ice scoop holders are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment and Utensils, Air-Drying Required
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried and/or adequately drained before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Physical Facilities/Repairing
Observation: Observed the floor in the kitchen is not maintained in good repair. The concrete has worn down to bare rock.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions
Observation: The floors, walls and ceilings throughout the establishment are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/31/2016 | Routine | |
When cooling foods, please ensure they are loosely covered/uncovered.
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An employee was eating in an area where contamination of exposed food or clean equipment may occur.
Correction: An employee shall eat, drink, or use any form of tobacco only in designated areas where the contamination of exposed food
- Contamination from Hands/Preventing Contamination by Employees (corrected on site) (repeated violation)
Observation: Food employee contacting exposed RTE food with bare hands. Observed employee handling RTE chicken.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Observed shell eggs stored directly over RTE food.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
|
11/20/2015 | Risk Factor | |
Please ensure labeling system for foods is consistent. Either the day the food should be sold, discarded, or consumed, OR the day the food is prepared on. Cool foods properly, do not cover at all, or loosely cover foods until all the way cool. Cooling hand out given to PIC.
- Reheating for Hot Holding (corrected on site)
Observation: The chili (110 F) that is cooked, cooled, and reheated for hot holding was not reheated so all parts of the food reached a temperature of at least 74ºC (165ºF) for 15 seconds.
Correction: Time/temperature control for safety food that is cooked, cooled and reheated for hot holding shall be reheated so that all parts of the food reach a temperature of at least 74ºC (165ºF) for 15 seconds. When food is held, cooled, and reheated in a food establishment, there is an increased risk from contamination caused by personnel, equipment, procedures, or other factors. If food is held at improper temperatures for enough time, pathogens have the opportunity to multiply to dangerous numbers. Proper reheating provides a major degree of assurance that pathogens will be eliminated. The potential for growth of pathogenic bacteria is greater in reheated cooked foods than in raw foods. This is because spoilage bacteria, which inhibit the growth of pathogens by competition on raw product, are killed during cooking. Subsequent recontamination will allow pathogens to grow without competition if temperature abuse occurs.
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site)
Observation: Several foods prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded. Labels are not consistent on products.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The food-contact surfaces of plates and knives stored as clean are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site) (repeated violation)
Observation: Surfaces of the ice machine are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
|
08/24/2015 | Risk Factor | |
- Cooling Methods (corrected on site)
Observation: Observed improper cooling methods for some cooked items and items for salad bar (cold). Macaroni- 45 F, Potatoes- 70 F, black beans- 60 F.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Food-Contact Surfaces/Cleanability
Observation: Observed chips and cracks in some equipment/food containers.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Equipment/Fixed, Spacing or Sealing
Observation: The caulking on mainline hand sink, warewashing area, and service sinks are in poor repair/missing.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Observed can opener in need of cleaning.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Cleanser, Availability (corrected on site)
Observation: Observed hand sink on mainline without soap.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
- Handwashing Signage (corrected on site) (repeated violation)
Observation: Observed no handwashing sign at mainline hand sink.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
|
03/30/2015 | Routine | |
Todays inspection was a follow-up to an NOV dated 21 November. Substantial compliance observed. Please continue to log temps not only of units, but of TCS foods as well.
No violation noted during this evaluation. | 12/05/2014 | Follow-up | |
Due to the pattern of violations, a Notice of Violation will be issued. A follow-up inspection will be conducted on or about 14 (fourteen) days. Please service refrigeration units not capable of maintaining food 41F or below.
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: Observed employee drink in food prep area without a lid.
Correction: Employees may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands (2) The container and (3) Exposed food clean equipment, utensils, and linens and unwrapped single-service and single-use articles.
- Critical: Contamination from Hands/Preventing Contamination by Employees (repeated violation)
Observation: Observed food employee handling RTE food with bare hands. Corrected by instruction.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Observed raw beef stored next to RTE Veggies in cooler.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Observed improper hot holding of foods: fried tomatoes-89F, cooked onions-78F, cooked baked potatoes-75F. Corrected by reheating.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Observed cold holding of several items above 41F. Motzerella-47F, cheese-50F, heavy cream-63F, pork ribs-45F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site)
Observation: Observed dish machine at less than 50 PPM. Employees are utilizing 3 compartment sink until serviced.
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in chemical manual or mechanical operations, including the application of sanitizing chemicals by immersion, manual swabbing, brushing, or pressure spraying methods, using a solution as specified under section 4-501.114 by providing: (1) An exposure time of at least 10 seconds for a chlorine solution specified under paragraph 4-501.114(A), (2) An exposure time of at least 7 seconds for a chlorine solution of 50 mg/L that has a pH of 10 or less and a temperature of at least 38°C (100°F) or a pH of 8 or less and a temperature of at least 24°C (75°F), (3) An exposure time of at least 30 seconds for other chemical sanitizing solutions, or (4) An exposure time used in relationship with a combination of temperature, concentration, and pH that, when evaluated for efficacy, yields sanitization as defined in Subparagraph 1-201.10(B). Efficacious sanitization depends on warewashing being conducted within certain parameters. Time is a parameter applicable to both chemical and hot water sanitization. The time hot water or chemicals contact utensils or food-contact surfaces must be sufficient to destroy pathogens that may remain on surfaces after cleaning. Other parameters, such as rinse pressure, temperature, and chemical concentration are used in combination with time to achieve sanitization.
|
11/17/2014 | Risk Factor | |
Use smaller portions when storing TCS product in the wait station counter top refrigeration unit. Chlorine dishmachine at the bar and in the kitchen checked for proper concentration using the provided test strips. Surfaces of the kitchen floor observed damaged. Some ceiling tile in the kitchen observed in need of cleaning/replacing. FDA Form 1-B left with the person in charge.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Ranch dressing and guacamole made in the establishment observed cold holding at the improper temperature in the service station counter refrigerator (43 F - 45 F). Product was portioned into smaller containers by the person in charge and placed under refrigeration.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink located at the cook-line was observed slanted and not properly attached to the wall. Maintenance personnel repaired the sink during the time of inspection.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
|
07/25/2014 | Risk Factor | |
Restaurant uses food coloring in some dishes and also uses a filter powder when cleaning the cooking oil. The rooftop bar area was not open during the time of inspection.
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Employee observed placing shredded cheese on a plate to be served with his/her bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Food Storage Containers, Identified with Common Name of Food (corrected on site)
Observation: Container of cooking oil and a container of vinegar at the cook-line observed not properly labeled.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- Cooling Methods, Food containers
Observation: Containers of blue cheese dressing, ranch dressing, and diced tomatoes in the top portion of the preparation refrigeration unit(s) observed portioned to the top of the food containers. Recommend reducing the volume in the containers to provide a better rate of cooling.
Correction: When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (1) Arranged in equipment to provide maximum heat transfer through the container walls
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: Some surfaces of the food slicer observed in need of cleaning.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Bar nozzle holsters in the wait station at the main bar observed in need of cleaning.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Signage (corrected on site)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: Ceiling vents above the cook-line observed in need of cleaning. Grease build observed under the cook-line stove/oven filters.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
|
03/26/2014 | Routine | |
The facility was observed smoking meat outside in an enclosed smoker. The facility was given the procedural memorandum for outdoor cooking at licensed food establishments. The facility needs approval from our department and any other applicable agency and must follow all the policies in the memorandum for outdoor cooking.
Do not stack cut lettuce above the top of the pan line in the top portion of the cook's prep refrigerator in order for it to maintain 41 F or below.
The bar dish machine is not being used
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site) (repeated violation)
Observation: Sauteed onions on the grill not over heat found hot holding at the improper temperature of 110 F. These onions were discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Rice and clam chowder in the "Kolpak" walk-in refrigerator downstairs found cold holding at the improper temperatures of 44-45 F. The unit thermostat was adjusted to be 4-5 F cooler.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The slicer is not clean to sight and touch. Wash, rinse, sanitize, and air dry the slicer prior to using again.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sinks/Numbers and Capacities
Observation: There are not an adequate number of handwashing sinks necessary for the convenient use by employees. There is no handwashing sink outside by the smoker.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
|
12/06/2013 | Follow-up | |
1. Ensure all chemical bottles are properly labelled
- Shellstock Identification
Observation: A container of shellstock (oysters) does not bear a tag or label or bears a tag or label that does not contain all the information as specified by law.
Correction: A container of shellstock that does not bear a tag or label or that bears a tag or label that does not contain all the information as specified by law shall be subject to a hold order, as allowed by law, or seizure and destruction in accordance with 21 CFR Subpart D - Specific Administrative Decisions Regarding Interstate Shipments, Section 1240.60(d).
- Shellstock, Maintaining Identification
Observation: Shellstock tag is missing from the container of oysters.
Correction: Shellstock tags shall remain attached to the container in which the shellstock are received until the container is empty. The date when the last shellstock from the container is sold or served shall be recorded on the tag or label. The identity of the source of shellstock that are sold or served shall be maintained by retaining shellstock tags or labels for 90 calendar days from the dates of harvest: (1) Using an approved record keeping system that keeps the tags or labels in chronological order correlated to the date when, or dates during which, the shellstock are sold or served
- Critical: Potentially Hazardous Food, Hot Holding (corrected on site)
Observation: Sauteed onions on the edge of the grill hot holding at the improper temperature of 111 F. Reheated to 165 F for 15 seconds. Maintain at 135 F or above on the grill.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Cheeses in the downstairs "Norlake" walk-in refrigerator cold holding at the improper temperature of 48 F. Adjust unit to a colder temperature and/or relocate foods to other refrigeration. Cajun rice and roast beef in the downstairs "Kolpack" refrigerator cold holding at the improper temperature of 45-46 F. Move this product to the back of the unit. Sliced turkey and shredded lettuce at 44-45 F in the top portion of the cook's "True" two door prep refrigerator. Cover these items.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The some cutting boards and the slicer were is not clean to sight and touch. Wash, rinse, sanitize, and air dry the slicer prior to using again. Remove stains from the cutting boards.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. Knives observed washed in the two compartment sink but were not sanitized. Instructed manager to wash, rinse, sanitize, and air dry utensils.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site)
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in a chemical manual or mechanical operations, using a proper solution (bar dish machine). Use three compartment sink until repaired.
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in chemical manual or mechanical operations, including the application of sanitizing chemicals by immersion, manual swabbing, brushing, or pressure spraying methods, using a solution as specified under section 4-501.114 by providing: (1) An exposure time of at least 10 seconds for a chlorine solution specified under paragraph 4-501.114(A), (2) An exposure time of at least 7 seconds for a chlorine solution of 50 mg/L that has a pH of 10 or less and a temperature of at least 38°C (100°F) or a pH of 8 or less and a temperature of at least 24°C (75°F), (3) An exposure time of at least 30 seconds for other chemical sanitizing solutions, or (4) An exposure time used in relationship with a combination of temperature, concentration, and pH that, when evaluated for efficacy, yields sanitization as defined in Subparagraph 1-201.10(B). Efficacious sanitization depends on warewashing being conducted within certain parameters. Time is a parameter applicable to both chemical and hot water sanitization. The time hot water or chemicals contact utensils or food-contact surfaces must be sufficient to destroy pathogens that may remain on surfaces after cleaning. Other parameters, such as rinse pressure, temperature, and chemical concentration are used in combination with time to achieve sanitization.
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site)
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in the hot water mechanical operations by being cycled through equipment that is properly set up and/or achieving a utensil surface temperature of 160°F as measured by an irreversible registering temperature indicator (kitchen dish machine). Use three compartment sink until repaired.
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in hot water mechanical operations by being cycled through equipment that is set up as specified under sections 4-501.15, 4-501.112, and 4-501.113 and achieving a utensil surface temperature of 71°C (160°F) as measured by an irreversible registering temperature indicator. When surface temperatures of utensils passing through warewashing machines using hot water for sanitizing do not reach the required 71°C (160°F), it is important to understand the factors affecting the decreased surface temperature. A comparison should be made between the machine manufacturer's operating instructions and the machine's actual wash and rinse temperatures and final rinse pressure. The actual temperatures and rinse pressure should be consistent with the machine manufacturer's operating instructions and within limits specified in sections 4-501.112 and 4-501.113. If either the temperature of pressure of the final rinse spray is higher than the specified upper limit, spray droplets may disperse and begin to vaporize resulting in less heat delivery to utensil surfaces. Temperatures below the specified limit will not convey the needed heat to surfaces. Pressures below the specified limit will result in incomplete coverage of the heat-conveying sanitizing rinse across utensil surfaces.
- Hand Drying Provision
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
|
11/26/2013 | Risk Factor | |
"Keep It Clean" DES poster provided.
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Employees observed contacting ready-to-eat (RTE) food with their bare hands. Line employee handling sliced deli cheese with bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph (D) of this section, food employees may not contact exposed, RTE food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Buttermilk at 46oF, cooked chicken at 48oF, grated cheese at 47oF, in Continental 1 door line reach in unit. Items moved to properly functioning unit.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment Food-Contact Surfaces and Utensils/Not Potentially Hazardous/Cleaning Frequency
Observation: Surfaces of the soda gun nozzles at the back bar are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not potentially hazardous (time/temperature control for safety food) shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sinks at back prep area and at middle bar area used for purposes other than handwashing. Back prep area hand sink observed with food debris in basin. Middle bar area hand sink observed with lemons in basin.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Handwashing Signage (corrected on site)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees. No hand wash sign at main bar hand sink and at far rooftop bar hand sink. VDH hand wash signs provided.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
|
07/08/2013 | Risk Factor | |
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Tongs and spatulas are improperly stored on working tables and oven handles.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: The following foods were observed at improper cold holding temperature:
1. Rice (49F) and Chicken (56F) in "True" 4-door refrigerator.
2. Half-n-half (49F) in "True" 1-dr refrigerator (# 15).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface of the wooden enclosures for oudoor ice machines is not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (corrected on site)
Observation: The food-contact surface of several tongs and spatulas is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surface of the deep fryers is not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Critical: Handwashing Sinks/Numbers and Capacities
Observation: Cookline handwashing sink has been taken off.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Physical Facilities/Repairing
Observation: The floor on cookline and warewashing area is not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Critical: Sanitizers, Criteria/Chemicals for Food Contact Surfaces
Observation: Warewashing machine dispensing chlorine >> 200 ppm.
Correction: Chemical sanitizers and other chemical antimicrobials applied to food-contact surfaces shall meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions). Chemical sanitizers are included with poisonous or toxic materials because they may be toxic if not used in accordance with requirements listed in the Code of Federal Regulations (CFR). Large concentrations of sanitizer in excess of the CFR requirements can be harmful because residues of the materials remain. The CFR reference that is provided lists concentrations of sanitizers that are considered safe.
|
03/07/2013 | Routine | |
Restaurant representatives - add corrected or new information about Whitlow's On Wilson, 2854 Wilson Blvd, Arlington, VA 22201 »