- Hands and Arms/When to Wash (corrected on site)
Observation: Observed an employee fail to wash hands after sneezing and touching clean equipment. Corrected by instruction.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Equipment/Cooking and Baking/Cleaning Frequency (corrected on site) (repeated violation)
Observation: Observed microwave in need of cleaning on mainline.
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
|
12/03/2015 | Risk Factor | |
Today's inspection was a follow-up for an NOAV issued for cold holding. Substantial compliance observed, however if cold holding is observed again, a Fact-Finding conference will be held. Please ensure temperatures are taken daily a minimum of 3 times/(every 4 hours). Documenting these temperatures are best.
No violation noted during this evaluation. | 10/05/2015 | Follow-up | |
Due to the pattern of violations, an Notice of Alleged Violation (NOAV) will be issued. Re-inspection will occur on or after 30 days (02 October 2015).
- Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Several foods in 1/dr counter unit and 2/dr salad prep unit observed cold holding at the improper temperatures.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The food-contact surfaces of the slicer, and several pieces of equipment and utensils stored as clean are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site) (repeated violation)
Observation: Surfaces of the ice machine and can opener are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station at the servers station is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
09/02/2015 | Risk Factor | |
Today's inspection was a follow-up for repeat priority violations. Substantial compliance observed, all temperatures were <41 F. Thank you!
No violation noted during this evaluation. | 05/14/2015 | Follow-up | |
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Food preparation and dispensing utensils are improperly stored. Ice cream scoop was not located in the water of the dipper well. Observed utensils stored between counter units.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Wiping Cloths, Use Limitation (corrected on site)
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Food Preparation/Protection From Environmental Sources
Observation: Observed no splash guard at middle hand washing sink on mainline. Food is exposed to splash.
Correction: During preparation, unpackaged food shall be protected from environmental sources of contamination. Food preparation activities may expose food to an environment that may lead to the food's contamination. Just as food must be protected during storage, it must also be protected during preparation. Sources of environmental contamination may include splash from cleaning operations, drips from overhead air conditioning vents, or air from an uncontrolled atmosphere such as may be encountered when preparing food in a building that is not constructed according to Food Code requirements.
- Cooling Methods
Observation: Methods used for cooling poached broccoli, noodles, lettuce, chorizo, chicken, turkey, and boiled eggs can not be accomplished with the time and temperature criteria.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Cooling Methods, Food containers
Observation: Food container of chicken wings, noodles, and several other items was not arranged to provide maximum heat transfer and/or loosely covered, or uncovered while cooling.
Correction: When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (1) Arranged in equipment to provide maximum heat transfer through the container walls
- Time/Temperature Control for Safety Food, Cold Holding (repeated violation)
Observation: Observed meat and cheese arrangement- 46 F, chipoltle mayo-70F, cold holding at the improper temperature.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Food-Contact Surfaces/Cleanability
Observation: The food-contact surfaces of several plastic food containters are not smooth, free of breaks, cracks, chips, and accessible for cleaning and inspection by an approved method.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Sanitizing Solutions, Testing Devices
Observation: A test kit or other device that accurately measures the concentration of the sanitizing solution is not provided. Test kit was not accurate and expired.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The "Continental" 3 drawer prep unit near right of mainline is not maintained in a state of repair and condition. The lid is in poor repair. The hand washing sink's handle on the mainline is in poor repair. Counter unit is 50F.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces (corrected on site) (repeated violation)
Observation: The surfaces of the all of the mainline cutting boards are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The food-contact surfaces of the slicer not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: The in-use utensils stored on prep units used with time/temperature control for safety are not cleaned throughout the day at least every 4 hours.
Correction: If used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned throughout the day at least every 4 hours. Microorganisms may be transmitted from a food to other foods by utensils, cutting boards, thermometers, or other food-contact surfaces. Food-contact surfaces and equipment used for time/temperature control for safety foods should be cleaned as needed throughout the day but must be cleaned no less than every 4 hours to prevent the growth of microorganisms on those surfaces.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the bar soda gun nozzles and can opener are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Cooking and Baking/Cleaning Frequency
Observation: The cavity and/or door seal of the microwave ovens are not cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure..
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surfaces of the fryer cabinets, dry food storage containers, and dry food storage shelving as well as shelving over mainline not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning. Dish machine sanitizer concentration was 0 ppm.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Hand Drying Provision
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food. Area above salad prep unit is missing a light, area does not have adequate lighting.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
04/27/2015 | Routine | |
Several cutting boards observed scratched, scoured and in need of replacing. The walk-in unit was being serviced by the repair technician during the time of inspection (ice build-up on the condenser). Ensure that cold holding units maintain temperature at 41 F or below. The interior of the fryer cabinets observed in need of cleaning. The plumbing connections under the middle cook-line handsink were observed leaking. Exterior of the dry ingredient containers observed in need of cleaning. Provide test strips for the Victory wash solution. Ensure that the chlorine sanitizer concentration in the dishmachine measuring between 50 ppm - 100 ppm. The wall/floor in the 3-compartment sink and dishmachine area observed in need of cleaning. HVAC ceiling vents throughout the facility in need of cleaning. The main water line in the back near the chemical storage area was observed with a small leak.
- Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before engaging in food preparation after rubbing his/her face with the foodservice gloves on during food preparation.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: Some cutting boards observed in need of cleaning and sanitizing (recommend replacing several).
Correction: Properly clean and sanitize equipment food contact surfaces.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: The beverage dispensing nozzles at the bar were observed in need of cleaning and sanitizing.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: The chlorine sanitizer solution in the mechanical dishmachine was observed at improper concentration (0 ppm). The sanitizer bucket was observed empty and was replaced by the person in charge. A service request has also been placed by the person in charge. Properly sanitize dishes/utensils in the 3-compartment sink when needed.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing unit in the wait station area was observed being used as a dump station. Employee observed rinsing a spray bottle in the middle cook-line handsink.
Correction: The handwashing facility identified above is to be used for washing hands only.
|
12/15/2014 | Risk Factor | |
- Critical: Contamination from Hands/Preventing Contamination by Employees (corrected on site)
Observation: Food employee contacting exposed RTE food with bare hands. Employee observed cutting lemons with bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- RTE, TCS, Date Marking/Commercially Processed Food (corrected on site)
Observation: Remaining unsliced portions of deli turkey, observed in walk in, prepared and packaged by a food processing plant opened and held for more than 24 hours was not clearly marked at the time the original container was opened in the food establishment to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded. Corrected by instruction.
Correction: Refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature and time combination specified in paragraph (A) of this section and: (1) The day the original container is opened in the food establishment shall be counted as Day 1
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact equipment surface(s) of the onion choppers stored as clean, and two of the line prep top cutting surfaces, is(are) not clean to sight and touch. Onion choppers removed for cleaning. Cutting boards were in need of replacement.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Critical: Sanitized/Hot Water and Chemical/Methods
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in the hot water mechanical operations by being cycled through equipment that is properly set up and/or achieving a utensil surface temperature of 160°F as measured by an irreversible registering temperature indicator. Call for service placed for ware washing machine.
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in hot water mechanical operations by being cycled through equipment that is set up as specified under sections 4-501.15, 4-501.112, and 4-501.113 and achieving a utensil surface temperature of 71°C (160°F) as measured by an irreversible registering temperature indicator. When surface temperatures of utensils passing through warewashing machines using hot water for sanitizing do not reach the required 71°C (160°F), it is important to understand the factors affecting the decreased surface temperature. A comparison should be made between the machine manufacturer's operating instructions and the machine's actual wash and rinse temperatures and final rinse pressure. The actual temperatures and rinse pressure should be consistent with the machine manufacturer's operating instructions and within limits specified in sections 4-501.112 and 4-501.113. If either the temperature of pressure of the final rinse spray is higher than the specified upper limit, spray droplets may disperse and begin to vaporize resulting in less heat delivery to utensil surfaces. Temperatures below the specified limit will not convey the needed heat to surfaces. Pressures below the specified limit will result in incomplete coverage of the heat-conveying sanitizing rinse across utensil surfaces.
- Handwashing Sink/Using/Operation and Maintenance
Observation: The handwashing sink located at the wait station was observed without a supply of hot water.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Hand Drying Provision (corrected on site)
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
|
09/08/2014 | Risk Factor | |
1. Wash hands frequently.
2. Do not fill containers above fill-line to keep foods at proper cold holding temperature.
3. Ice-cream dipper well was turned off - (corrected).
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: Open beverage containers not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Critical: Time/Temperature Control for Safety Food, Cold Holding (repeated violation)
Observation: The following foods were observed at improper cold holding temperature:
1. Cheddary (46F) and Blue cheese (44F) in 6-drawer ref. (under grill) - (placed on ice)
2. Buttermilk (46F) in "Silver King" 1-dr counter refrigerator - (moved into WIC)
3. Blue cheese (46F - iced up) and Chicken (52F - discarded) in 2-dr prep refrigerator (fried)
4. Sour cream (47F), Salsa (47F) and Guacamole (48F) in 2-dr prep ref. (pantry) - (placed on ice in WIC)
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment/Good Repair and Proper Adjustment
Observation: The following equipment are not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design:
1. "Silver King" 1-dr counter refrigerator's door is not closing properly
2. 3-compartment sink's blockers are not closing properly to hold water
3. Spray hose by warewashing machine is leaking and taped
4. Ice crem dipper well is missing drain stopper
5. Ventilation hood over dish machine is missing filter
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces (corrected on site)
Observation: The surfaces of the cutting boards are no longer effectively cleaned and sanitized.
Correction: (removed) - Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (corrected on site)
Observation: The nonfood-contact surface of several large plastic containers is not kept free of an accumulation of dust, dirt, food residue, and/or other debris. Deep fryers are also in need of cleaning.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment and Utensils, Air-Drying Required (corrected on site)
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
|
04/22/2014 | Routine | |
Maintain refrigerators at 37-38
ºF
during the rush hours.
Wash hands frequently.
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Raw shell eggs and raw shrimp were observed stored over ready-to-eat foods in the prep refrigerators.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Diced tomatoes(43ºF), salsa(44ºF), and shredded cheese(45ºF) in the Continental 2 drawer refrigerator were observed cold holding at improper temperatures. The refrigerator will be adjusted and the food was relocated.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station in the servers area is being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
|
12/19/2013 | Risk Factor | |
- Critical: Package Integrity (corrected on site)
Observation: Two dented can of green Chile were found in the cans rack (discarded).
Correction: Food packages shall be in good condition and protect the integrity of the contents so that food is not exposed to adulteration or potential contaminants.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Pico de gallo at 46 F, avocado mix at 44 F, discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (repeated violation)
Observation: All the cutting boards are worn-out with a lots of cuts and stains. Dishwashing machine is not ejecting sanitizer food contact surfaces are not being sanitized.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
|
09/17/2013 | Risk Factor | |
DES "Keep It Clean" Poster provided.
- Critical: Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An open beverage container and/or a closed beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Cooling Methods (corrected on site)
Observation: Methods used for cooling portioned bagged cooked chicken can not be accomplished with the time and temperature criteria.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Bagged rice at 48oF in 2 door line prep unit. Raw chicken at 50oF, turkey burgers at 44oF in under grill drawer unit. Items moved to fully functional unit.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Temperature Measuring Devices, Ambient Air and Water
Observation: The ambient air or water temperature measuring device for the walk in freezer is not accurate.
Correction: Ambient air and water temperature measuring devices that are scaled only in Fahrenheit shall be accurate to +/- 3ºF in the intended range of use. A temperature measuring device used to measure the air temperature in a refrigeration unit is not required to be as accurate as a food thermometer because the unit's temperature fluctuates with repeated opening and closing of the door and because accuracy in measuring internal food temperatures is of more significance. If Fahrenheit thermometers are used, the 3ºF requirement applies because of the calibrated intervals of Fahrenheit thermometers.
- Equipment/Good Repair and Proper Adjustment
Observation: The caulking was moldy and in disrepair at the 3 part sink.
The caulking was in disrepair at the back hand washing sink.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment and Utensils, Air-Drying Required
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Plumbing System/Maintained in Good Repair
Observation: The faucet was observed leaking at the 3 part sink.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Light Bulbs, Protective Shielding
Observation: The light bulbs over the ware washing area are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Handwashing Signage (corrected on site)
Observation: No hand wash sign was available at back bar hand sink.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Physical Facilities/Repairing
Observation: The wall by the ware washing machine was observed in disrepair with mold build-up.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
|
05/29/2013 | Routine | |
Restaurant representatives - add corrected or new information about Rock Bottom Restaurant & Brewery, 4238 Wilson Blvd #1256, Arlington, VA 22203 »