- Food Storage - Clean and Dry Location (repeated violation)
Observation: Food stored on the floor or food stored less than 6" above the floor in the walk in cooler and freezer.;Elevate food storage onto approved shelving with minimum 6" legs or casters.
- Nonfood-Contact Surfaces - Corrosion Resistant/Nonabsorbent (repeated violation)
Observation: The nonfood contact surface of the wooden storage shelving is not corrosion resistant, nonabsorbent, and/or smooth.
Correction: Nonfood contact equipment that is exposed to splash, spillage, food soiling, or requires frequent cleaning must be smooth, durable, and nonabsorbent.
- Critical: Equipment and Utensils - Hot Water and Chemical Sanitizing* (corrected on site)
Observation: When tested, no sanitizer or a low concentration of chemical sanitizer was found in the wiping cloth bucket storing wiping cloths used on food contact surfaces..
Correction: Provide Chlorine at proper concentration of 50-100 ppm and immerse or expose food contact surfaces to sanitizing solution for adequate time.
- Light Bulbs Protective Shielding (repeated violation)
Observation: Light bulb in the storage area (Hall way) not shielded, coated, or otherwise shatter-resistant.
Correction: Shield or replace light bulb with a coated or shatter-resistant bulb.
- Toilet Rooms - Enclosed
Observation: Toilet room door is not provided with a self-closing door
Correction: Provide a self-closer for the toilet room door. Completely enclosed toilet facilities minimize the potential for the spread of disease by the movement of flies and other insects between the toilet facility and food preparation areas.
|
03/14/2016 | Routine | |
- Food Storage - Clean and Dry Location (repeated violation)
Observation: Food stored on the floor or food stored less than 6" above the floor of the walk in freezer;Elevate food storage onto approved shelving with minimum 6" legs or casters.
- Food Display (corrected on site)
Observation: The food on display is not protected from contamination. (unwrapped fresh fruit offered with no sneeze guards or cover)
Correction: Protect food on display by the use of packaging - counter, service line, or salad bar food guards - display cases - or other effective means to prevent contamination.
- Nonfood-Contact Surfaces - Corrosion Resistant/Nonabsorbent (repeated violation)
Observation: The nonfood contact surface of the dry storage shelving is not corrosion resistant, nonabsorbent, and/or smooth.
Correction: Nonfood contact equipment that is exposed to splash, spillage, food soiling, or requires frequent cleaning must be smooth, durable, and nonabsorbent.
- Cooling, Heating, and Holding Capacities
Observation: Walk in freezer was overstocked and is not sufficient in number or capacity to meet the food storage demands of the establishment.
Correction: Provide additional freezers necessary to maintain food in a frozen state. Overstocked equipment does not allow for proper air circulation and/or heat transfer. Improper food storage temperatures are a major contributing factor to foodborne illness.
- Light Bulbs Protective Shielding
Observation: Light bulb in restroom vestibule not shielded, coated, or otherwise shatter-resistant.
Correction: Shield or replace light bulb with a coated or shatter-resistant bulb.
- Toilet Rooms - Closing Toilet Room Doors
Observation: Toilet room doors are being kept open
Correction: Keep toilet room doors closed except when cleaning or during maintenance operations to prevent insect and rodent entrance and the associated potential for the spread of disease.
|
12/11/2015 | Routine | |
- Food Storage - Clean and Dry Location (repeated violation)
Observation: Food stored on the floor or food stored less than 6" above the floor in the walk in cooler/freezer;Elevate food storage onto approved shelving with minimum 6" legs or casters.
- Nonfood-Contact Surfaces - Corrosion Resistant/Nonabsorbent
Observation: The nonfood contact surface of the wooden storage shelving is not corrosion resistant, nonabsorbent, and/or smooth.
Correction: Nonfood contact equipment that is exposed to splash, spillage, food soiling, or requires frequent cleaning must be smooth, durable, and nonabsorbent.
|
09/08/2015 | Routine | |
- Utensils - In-Use - Between-Use Storage (corrected on site)
Observation: Dispensing utensils improperly stored between uses. (Ice Scoop stored in ice machine without handle up)
Correction: Store in-use utensils or dispensing utensils in one of the following manners: 1) In the food with their handles above the top of the food and the container. 2) In food that is not potentially hazardous with their handles above the top of the food within containers or equipment that can be closed. 3) On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized every 4 hours. 4) In running water of sufficient velocity to flush particulates to the drain. 5) In a clean, protected location if the utensils are used only with a food that is not potentially hazardous. 6) In a container of water if the water is maintained at a temperature of at least 135°F.
- Food Storage - Clean and Dry Location (repeated violation)
Observation: Food stored on the floor or food stored less than 6" above the floor in the walk in freezer;Elevate food storage onto approved shelving with minimum 6" legs or casters.
|
04/07/2015 | Routine | |
- Food Storage - Clean and Dry Location
Observation: Food in walk-in-freezer stored on the floor or food stored less than 6" above the floor.;Elevate food storage onto approved shelving with minimum 6" legs or casters.
- Sanitizing Solutions, Testing Devices
Observation: There is no properly working test kit provided in the facility for monitoring the concentration of the chemical sanitizing solutions.
Correction: Obtain a Cl Bleach test kit so that employees can accurately monitor the concentration of the sanitizing solutions and maintain them at a safe and effective level.
|
12/16/2014 | Routine | |
- Nonfood-Contact Surfaces - Corrosion Resistant/Nonabsorbent (repeated violation)
Observation: The nonfood contact surface of the wooden storeage shelving is not corrosion resistant, nonabsorbent, and/or smooth.
Correction: Nonfood contact equipment that is exposed to splash, spillage, food soiling, or requires frequent cleaning must be smooth, durable, and nonabsorbent.
- Light Bulbs Protective Shielding
Observation: Light bulb in rear storeage area not shielded, coated, or otherwise shatter-resistant.
Correction: Shield or replace light bulb with a coated or shatter-resistant bulb.
- Toilet Rooms - Enclosed
Observation: Toilet room door is not provided with a self-closing door. (Kitchen employee restroom)
Correction: Provide a self-closer for the toilet room door. Completely enclosed toilet facilities minimize the potential for the spread of disease by the movement of flies and other insects between the toilet facility and food preparation areas.
|
09/08/2014 | Routine | |
- Critical: Food - Packaged and Unpackaged - Separation, Packaging, and Segregation* (corrected on site) (repeated violation)
Observation: The raw animal food on display is stored in a manner that may cause biological cross contamination of to ready-to-eat food (RTE).
Correction: Separate raw animal foods during storage, preparation, holding, and display from raw RTE food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw RTE food such as vegetables, and cooked RTE food.
- Physical Facilities in Good Repair
Observation: ceiling in stock room is not maintained in good repair
Correction: Maintain physical facilities in good repair. Poor repair and maintenance compromises the functionality of the physical facilities.
- Physical Facilities - Cleaning Frequency and Restrictions
Observation: wall behind dishwasher noted in need of cleaning.
Correction: All floors, walls, and ceilings must be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/11/2014 | Routine | |
- Critical: Food - Packaged and Unpackaged - Separation, Packaging, and Segregation* (corrected on site)
Observation: Raw foods of animal origin stored over ready-to-eat (RTE) food in the refrigeration unit. (Shell eggs and raw pork roast stored over cut strawberries)
Correction: Separate raw foods of animal origin during storage, preparation, holding, and display from raw RTE food including foods such as fish for sushi or molluscan shellfish, or other raw RTE food such as vegetables, and cooked RTE food.
- Utensils - In-Use - Between-Use Storage
Observation: Dispensing utensils improperly stored between uses. (ice scoop stored on top of ice machine)
Correction: Store in-use utensils or dispensing utensils in one of the following manners: 1) In the food with their handles above the top of the food and the container. 2) In food that is not potentially hazardous with their handles above the top of the food within containers or equipment that can be closed. 3) On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized every 4 hours. 4) In running water of sufficient velocity to flush particulates to the drain. 5) In a clean, protected location if the utensils are used only with a food that is not potentially hazardous. 6) In a container of water if the water is maintained at a temperature of at least 135°F.
- Cloths - Wiping Cloths - Use Limitation (corrected on site)
Observation: Wiping cloths improperly stored between use. (No sanitizer observed in water)
Correction: Ensure wet wiping cloths are stored in a chemical sanitizer at the proper concentration between use.
- Food Storage - Clean and Dry Location
Observation: Food stored on the floor or food stored less than 6" above the floor in the walk in coolers;Elevate food storage onto approved shelving with minimum 6" legs or casters.
- Food Display (repeated violation)
Observation: The food on display is not protected from contamination.(Sneeze guards are missing from one self service bar where food is served)
Correction: Protect food on display by the use of packaging - counter, service line, or salad bar food guards - display cases - or other effective means to prevent contamination.
- Nonfood-Contact Surfaces - Corrosion Resistant/Nonabsorbent (repeated violation)
Observation: The nonfood contact surface of the wooden storage shelving in the dry storage area is not corrosion resistant, nonabsorbent, and/or smooth.
Correction: Nonfood contact equipment that is exposed to splash, spillage, food soiling, or requires frequent cleaning must be smooth, durable, and nonabsorbent.
|
12/09/2013 | Routine | |
- Utensils - In-Use - Between-Use Storage (corrected on site)
Observation: In-use utensils improperly stored between use.
Correction: Store in-use utensils or dispensing utensils in one of the following manners: 1) In the food with their handles above the top of the food and the container. 2) In food that is not potentially hazardous with their handles above the top of the food within containers or equipment that can be closed. 3) On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized every 4 hours. 4) In running water of sufficient velocity to flush particulates to the drain. 5) In a clean, protected location if the utensils are used only with a food that is not potentially hazardous. 6) In a container of water if the water is maintained at a temperature of at least 135°F.
- Food Display
Observation: The food on display is not protected from contamination at the cambro island (Sneeze guards are missing)
Correction: Protect food on display by the use of packaging - counter, service line, or salad bar food guards - display cases - or other effective means to prevent contamination.
- Nonfood-Contact Surfaces - Corrosion Resistant/Nonabsorbent (repeated violation)
Observation: The nonfood contact surface of the Dry storage shelving is not corrosion resistant, nonabsorbent, and/or smooth.
Correction: Nonfood contact equipment that is exposed to splash, spillage, food soiling, or requires frequent cleaning must be smooth, durable, and nonabsorbent.
- Handwashing Signage/Handwashing Facilities (repeated violation)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all lavatories used by food employees
Correction: Provide a sign or poster that notifies food employees to wash their hands at all handwashing lavatories used by food employees.
|
09/10/2013 | Routine | |
Need to utilize chlorine test strips. i recommend that the Person in Charge take an offered ServSafe class.
- Critical: Demonstration of Knowledge* (corrected on site)
Observation: The person in charge failed to state the required temperatures and holding times for the following conditions of potentially hazardous food: (1) Refrigerated storage, (2) Hot holding, (3) Cooling, and (4) Reheating.
Correction: Ensure the designated person in charge (PIC) is knowledgeable about foodborne disease prevention, Hazardous Analysis Critical Control Point principles and Regulation requirements. The PIC should be prepared to recognize conditions that may contribute to foodborne illness. The PIC must also recognize conditions that fail to comply with Regulation requirements and be authorized to take the appropriate preventive and corrective actions to ensure that the Regulations' objectives are fulfilled. We discussed the above HACCP principles and I feel that she now has a good understanding.
- Critical: Demonstration of Knowledge* (corrected on site)
Observation: The person in charge failed to explain the details of how employees comply with the Hazardous Analysis Critical Control Point plan if law, these regulations, or an agreement between the regulatory authority and the establishment requires a plan.
Correction: Ensure the designated person in charge (PIC) is knowledgeable about foodborne disease prevention, Hazardous Analysis Critical Control Point principles and Regulation requirements. The PIC should be prepared to recognize conditions that may contribute to foodborne illness. The PIC must also recognize conditions that fail to comply with Regulation requirements and be authorized to take the appropriate preventive and corrective actions to ensure that the Regulations' objectives are fulfilled.
- Nonfood-Contact Surfaces - Corrosion Resistant/Nonabsorbent (repeated violation)
Observation: The nonfood contact surface of the shelves in the storage room is not corrosion resistant, nonabsorbent, and/or smooth. They are in poor condition!
Correction: Nonfood contact equipment that is exposed to splash, spillage, food soiling, or requires frequent cleaning must be smooth, durable, and nonabsorbent.
- Temperature - Food Temperature Measuring Devices - Provided
Observation: The Person in Charge could not produce an appropriate food temperature measuring device to verify cooking temperatures of thin foods such as meat patties or fish filets.
Correction: A temperature measuring device with a suitable small-diameter probe that is designed to measure the temperature of thin masses shall be provided and readily accessible to accurately measure the temperature in thin foods such as meat patties and fish filets.
|
05/02/2013 | Routine | |
- Person in Charge (corrected on site)
Observation: Unauthorized personnel such as children or customers in the food preparation, food storage, or warewashing areas.(Teachers observed in the kitchen retrieving food)
Correction: Remove unauthorized personnel. The person in charge shall not permit persons unnecessary to the food establishment operation in the food preparation, food storage, or warewashing areas.
- Critical: Food - Packaged and Unpackaged - Separation, Packaging, and Segregation* (corrected on site)
Observation: Raw foods of animal origin stored over ready-to-eat (RTE) food in the refrigeration unit.(Raw sausage & Ground beef over carrots, taco shells)
Correction: Separate raw foods of animal origin during storage, preparation, holding, and display from raw RTE food including foods such as fish for sushi or molluscan shellfish, or other raw RTE food such as vegetables, and cooked RTE food.
- Utensils - In-Use - Between-Use Storage (corrected on site)
Observation: Dispensing utensils improperly stored between uses.(Ice Scoop)
Correction: Store in-use utensils or dispensing utensils in one of the following manners: 1) In the food with their handles above the top of the food and the container. 2) In food that is not potentially hazardous with their handles above the top of the food within containers or equipment that can be closed. 3) On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized every 4 hours. 4) In running water of sufficient velocity to flush particulates to the drain. 5) In a clean, protected location if the utensils are used only with a food that is not potentially hazardous. 6) In a container of water if the water is maintained at a temperature of at least 135°F.
- Nonfood-Contact Surfaces - Corrosion Resistant/Nonabsorbent
Observation: The nonfood contact surface of the dry storage shelving is not corrosion resistant, nonabsorbent, and/or smooth.
Correction: Nonfood contact equipment that is exposed to splash, spillage, food soiling, or requires frequent cleaning must be smooth, durable, and nonabsorbent.
- Handwashing Signage/Handwashing Facilities
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all lavatories used by food employees
Correction: Provide a sign or poster that notifies food employees to wash their hands at all handwashing lavatories used by food employees.
|
01/16/2013 | Routine | |
Restaurant representatives - add corrected or new information about Honaker High School, 1795 Thompson Creek Road, Honaker, VA »