- Food Temperature Measuring Devices
Observation: A temperature measuring device with a suitable small-diameter probe to measure thin masses is not provided and readily accessible to accurately measure the temperature in thin foods.
Correction: A temperature measuring device with a suitable small-diameter probe that is designed to measure the temperature of thin masses shall be provided and readily accessible to accurately measure the temperature in thin foods such as meat patties and fish filets. When determining the temperature of thin foods, those having a thickness less than 13 mm (1/2 inch), it is particularly important to use a temperature sensing probe designed for that purpose. Bimetal, bayonet style thermometers are not suitable for accurately measuring the temperature of thin foods such as hamburger patties because of the large diameter of the probe and inability to accurately sense the temperature at the tip of the probe. However, temperature measurements in thin foods can be accurately determined using a small-diameter probe 1.5 mm (0.059 inch), or less, connected to a device such as thermocouple thermometer.
- Equipment/Good Repair and Proper Adjustment
Observation: The gasket to the 1-door Beverage Air reach-in refrigerator was observed damaged and in need of repair. Some of the kitchen ceiling vents were observed damaged and in need of replacement.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: Interior of the reach-in freezer, interior/exterior of the fryer unit, storage shelving, and exterior of cook-line equipment observed in need of cleaning.
Correction: The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur and to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Handwashing Signage (repeated violation)
Observation: Handwashing sign observed not properly posted in the men's rest-room.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: Floor surface underneath and around kitchen equipment observed in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/28/2016 | Routine | |
Today's inspection was a follow-up for date marking and cold holding. Substantial compliance observed. Ice machines and soda nozzles were serviced as well. Thank you!
No violation noted during this evaluation. | 11/09/2015 | Follow-up | |
Observed food employee cooking/preparing food without a proper hair restraint. Corrected by instruction. Please ensure a CFM is present during ALL hours of operation. Consider acquiring additional CFMs. ORS interactive.
- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Observed cooked foods held over 24 hours without a date.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site) (repeated violation)
Observation: Observed soda gun and ice machine in need of cleaning.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Food Manager Certificate and Responsibility (corrected on site)
Observation: No CFM on duty. CFM arrived during inspection.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
06/25/2015 | Risk Factor | |
Today's inspection was a follow-up due to priority violations. Please clean non-food contact surfaces thoroughly, or enforcement action will occur. Clean all equipment, floors, walls, shelving, hood, and under equipment. Please ensure violations are corrected before next inspection.
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Observed chilli hot holding at 128 F. Reheated to 165 F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (repeated violation)
Observation: The food-contact surfaces of the slicer is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (repeated violation)
Observation: Surfaces of the can opener, ice machine, and soda gun nozzle are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
|
03/12/2015 | Follow-up | |
Due to the nature of violations, and repeat, re-inspection will be conducted in or about 30 days. Please send invoice of repair/servicing of dish machine.Utilize 3 compartment sink to sanitize equipment and utensils. Concentration of chlorine should be between 50-100 ppm. Utilize test strips to ensure machine is working properly, and concentration of sanitizer in 3 compartment sink is appropriate.
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An open beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Deli meats, and several cooked foods prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The food-contact surfaces of the slicer is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (repeated violation)
Observation: Surfaces of the can opener, ice machine, and soda gun nozzle are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Cooking and Baking/Cleaning Frequency
Observation: The cavity and door seal of the microwave ovens are not cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure..
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Equipment/Cooking and Baking/Cleaning Frequency
Observation: The food-contact surfaces of the grill, stove, and oven not cleaned at least every 24 hours.
Correction: The food-contact surfaces of cooking and baking equipment shall be cleaned at least every 24 hours. This section does not apply to hot oil cooking and filtering equipment if it is cleaned as specified in Subparagraph 4-602.11(D)(6). Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The nonfood-contact surfaces of the counter tops, carts, shelving, refrigerator handles and doors are not cleaned at a frequency necessary to preclude the accumulation of soil residues.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Equipment/Food-Contact/Before Use After Cleaning/Sanitized
Observation: Utensils and food-contact surfaces of equipment were not sanitized after cleaning.The dishwasher is not giving a read for chlorine sanitizer.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink in main kitchen is used for purposes other than handwashing. Observed mixing bowl and utensil inside the sink.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Refuse/Covering Receptacles
Observation: Receptacles or waste handling units for refuse, recyclables, and returnables kept outside the food establishment are not kept covered with tight-fitting lids or doors.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
- Handwashing Signage (repeated violation)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees. There is no handwashing sign posted in the mens lavatory.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Intensity/Lighting
Observation: The light intensity is below 10 foot candles in the walk-in cooler.
Correction: The light intensity shall be at least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in the walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning. Properly distributed light makes the need for cleaning apparent by making accumulations of soil conspicuous.
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food. Both hood lights are unserviceable.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Cleaning of Plumbing Fixtures
Observation: Plumbing fixtures are not clean at handwashing sink in main kitchen.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
|
02/10/2015 | Routine | |
2014 Health License was posted in kitchen. Relocate to area visible by customers.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Cooked potatoes at 47 F, cooked sausage patties at 46 F in True 1 door prep unit. Items relocated.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation (repeated violation)
Observation: Sliced deli meats, prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: The food establishment serves or sells raw or undercooked food and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. No consumer advisory information available for eggs cooked to order and steak.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Food-Contact Surfaces/Cleanability
Observation: The food-contact surface(s) of the 1 door prep top cutting board is(are) not smooth, free of breaks, open seams, cracks, chips, inclusions, pits, similar imperfections, finished to have smooth welds and joints, and/or accessible for cleaning and inspection by an approved method.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency
Observation: Surfaces of the soda gun nozzle are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees. No hand washing signage in men's restroom.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Cleaning, Frequency and Restrictions
Observation: The areas under equipment in kitchen are not cleaned as often as necessary to keep them clean.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Drying Mops
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
|
10/24/2014 | Routine | |
- RTE, PHF(TCS), Date Marking/On-Premises Preparation
Observation: Several ready to eat food containers prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment, Food-Contact Surfaces, and Utensils
Observation: The prep table cutting board needs cleaning, too many stains.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
|
12/16/2013 | Risk Factor | |
CFM notified that Bev Air 1 door uprt unit must not be used to hold PHF items until unit maintains an internal ambient temperature of 41oF or less.
- Critical: Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: An open beverage container and/or a closed beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: PHF items in Bev Air 1 door uprt holding at greater than 41oF, including deli roast beef at 48oF, deli cheese at 45oF, and scrapple at 48oF. Items relocated to functional unit.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation (repeated violation)
Observation: Meatloaf, mashed potatoes, cole slaw, and deli meat and cheese, prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
|
08/21/2013 | Risk Factor | |
"Keep It Clean" DES poster provided.
- Food Storage/Preventing Contamination from the Premises (repeated violation)
Observation: Stored food is not protected from contamination. Cases of beer stored on the floor in walk in.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: Sausage patties at 52oF, sliced tomatoes at 53oF in Superior 1 door prep.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: RTE, PHF(TCS), Date Marking/On-Premises Preparation (repeated violation)
Observation: Cooked meatballs, mashed potatoes, sliced deli ham and cheese, prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Critical: Food-Contact Surfaces/Cleanability
Observation: The food-contact surface of the Superior 1 door prep cutting board is not smooth, free of breaks, open seams, cracks, chips, inclusions, pits, similar imperfections, finished to have smooth welds and joints, and/or accessible for cleaning and inspection by an approved method.
Correction: Multiuse food-contact surfaces shall be: (1) Smooth
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surface of the exterior of the Superior 1 door prep and the deep fryer are not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
|
03/28/2013 | Routine | |
Restaurant representatives - add corrected or new information about Forest Inn, 5849-B Washington Blvd, Arlington, VA 22205 »