- Food Storage/Preventing Contamination from the Premises
Observation: Some boxes of food product observed improperly stored on the floor in the walk-in refrigerator.
Correction: Store food where it is not exposed to splash, dust, or other contamination and/or install an approved, durable and cleanable barrier between the splash source and the food to prevent contamination.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: Refrigeration gaskets, exterior/interior of refrigeration equipment, and the interior of the cook-line fryer unit were observed in need of cleaning.
Correction: The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur and to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment/Cooking and Baking/Cleaning Frequency
Observation: Interior/exterior of the cook-line ovens and cook-line stove were observed in need of cleaning.
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: No handsink located in the raw meat cutting area.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Hand Drying Provision (corrected on site)
Observation: Disposable paper towels observed not properly provided at the handsink in the bakery kitchen.
Correction: Each handwashing sink or group of adjacent handwashing sinks shall be provided with: (A) Individual, disposable towels
- Intensity/Lighting (repeated violation)
Observation: Some lights in the kitchen cook-line hood system and in the bakery kitchen observed in need of replacement.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: Floor surface under and around kitchen/cook-line equipment observed in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition (repeated violation)
Observation: Cook-line ventilation system observed in need of cleaning.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
- Sanitizers, Criteria/Chemicals for Food Contact Surfaces (corrected on site)
Observation: Chlorine sanitizer concentration in the bakery area wiping cloth bucket observed at a concentration greater than 200 ppm when tested with the chlorine sanitizer test strip (product was diluted by the person in charge).
Correction: Chemical sanitizers and other chemical antimicrobials applied to food-contact surfaces shall meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions). Chemical sanitizers are included with poisonous or toxic materials because they may be toxic if not used in accordance with requirements listed in the Code of Federal Regulations (CFR). Large concentrations of sanitizer in excess of the CFR requirements can be harmful because residues of the materials remain. The CFR reference that is provided lists concentrations of sanitizers that are considered safe.
|
03/18/2016 | Routine | |
Gaskets to the preparation units observed damaged and in need of repair. The cutting board at the meat cutting station was observed scratched, scoured and in need of resurfacing/replacing. Floor surface under/behind cooking equipment observed in need of cleaning. Several lights in the kitchen hood system observed out and in need of replacing. The condenser to the cook-line preparation unit was observed in need of cleaning. The plumbing connections under the kitchen side 3-compartment sink were observed leaking and in need of repair. Interior surfaces of the reach-in refrigeration equipment were observed in need of cleaning. The trash/debris observed next to the outside waste container area was in need of cleaning.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site) (repeated violation)
Observation: The handle to the manual knife sharpener in the meat cutting station was observed soiled and in need of cleaning and sanitizing.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: Handsink not observed provided in the area for cutting raw meat.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Cleaning of Plumbing Fixtures (repeated violation)
Observation: Kitchen handsink in the bakery station area observed in need of cleaning.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
|
11/13/2015 | Risk Factor | |
Cutting board at meat station observed scratched and scoured. Interior of refrigeration units observed in need of cleaning. Floor/wall surface under and around equipment observed in need of cleaning. Kitchen hood system observed in need of cleaning (the service company label shows that it is scheduled for August). Several lights in the kitchen hood system observed not working. Containers of food items observed improperly stored on the floor in the walk-in refrigerator. The storage shelving above the 3-compartment sink was observed rusted and in need of replacing. The light in the walk-in freezer was observed not working. Interior of the fryer equipment observed in need of cleaning. Floor under cook-line observed in need of cleaning. Storage shelving throughout kitchen observed in need of cleaning.
- Cooling, Cooked Food (corrected on site)
Observation: Bulk container of greens (55 F) prepared the previous day observed at improper temperature in the walk-in refrigerator. Product was discarded by the person in charge.
Correction: Cooked time/temperature control for safety food shall be cooled: (1) Within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site) (repeated violation)
Observation: Container of black beans (127 F) and a container of spinach (122 F) observed at improper temperature in the hot holding box. Product was reheated to 165+ by the person in charge.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: Handsink observed not provided in the raw meat cutting area.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Handwashing Signage
Observation: Handwash sign observed not posted at the bar handsink.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
|
07/30/2015 | Risk Factor | |
Spices and products offered for sale observed improperly labeled. Floors/walls throughout facility in need of cleaning. The storage shelving above the 3-compartment sink was observed rusted. Mold residue observed in the dishwashing area. Several containers of food items observed stored on the floor in the walk-in freezer. Ice build-up observed in the walk-in freezer. Hood vents in need of cleaning. Spray nozzle at 3-compartment sink observed leaking. No handsink observed in the meat cutting area.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: Cutting board used for raw meat observed soiled and in need of cleaning and sanitizing.
Correction:
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized (corrected on site)
Observation: Employee observed washing dishes at the 3-compartment sink without the sanitizer basin properly set-up.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Handwashing Cleanser, Availability (corrected on site)
Observation: There was no hand soap provided at the handsink in the bar/buffet area.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
- Critical: Sanitizers, Criteria/Chemicals for Food Contact Surfaces (corrected on site)
Observation: The chlorine wiping cloth bucket solution was observed at >200 ppm (a new solution was made and tested by the person in charge 50-100 ppm).
Correction: Chemical sanitizers and other chemical antimicrobials applied to food-contact surfaces shall meet the requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions). Chemical sanitizers are included with poisonous or toxic materials because they may be toxic if not used in accordance with requirements listed in the Code of Federal Regulations (CFR). Large concentrations of sanitizer in excess of the CFR requirements can be harmful because residues of the materials remain. The CFR reference that is provided lists concentrations of sanitizers that are considered safe.
|
11/19/2014 | Risk Factor | |
1. The entire kitchen, warewashing and bakery areas are in need of detail cleaning.
2. Light intensity is below minimum throughout the facility.
3. Some light bulbs under hood are burnt out
- Demonstration/Knowledge/Responding Correctly to the Inspector's Questions (corrected on site)
Observation: The person in charge did not demonstrate their knowledge of the required food temperatures and times for the safe cooking of time/temperature control for safety foods including meat, poultry, eggs, and fish.
Correction: Based on the risks inherent to the food operation, during inspections and upon request the person in charge shall demonstrate to the regulatory authority knowledge of foodborne disease prevention, application of the hazard analysis and critical control point principles, and the requirements of this Code. The person in charge shall demonstrate this knowledge by responding correctly to the inspector's questions as they relate to the specific food operation. The areas of knowledge include stating the required food temperatures and times for the safe cooking of time/temperature control for safety foods including meat, poultry, eggs, and fish.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site) (repeated violation)
Observation: Beef w/spinach (104F), mixed vegetables (116-122F), yellow peas (129F) in hot holding cabinet and spinach samosas (129F) in samosa-warmer box were observed at improper hot holding temperature.
Correction: (reheated) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Handwashing Sinks/Numbers and Capacities (corrected on site) (repeated violation)
Observation: No hand sink in the meat cutting section.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
|
07/21/2014 | Risk Factor | |
The light shield for the bakery was available and is due to be installed. Provide the invoice for the repairs made to the cook-line preparation unit.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: Meat hooks in the walk-in refrigerator observed in need of cleaning.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: There is no handsink located in the meat cutting section.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Liquid Wastes and Rainwater/Nonsewage
Observation: Ice build-up observed on the walk-in freezer condenser drain line.
Correction: Condensate drainage and other nonsewage liquids and rainwater shall be drained from point of discharge to disposal according to law. Liquid food wastes and rainwater can provide a source of bacterial contamination and support populations of pests. Proper storage and disposal of wastes and drainage of rainwater eliminate these conditions.
- Light Bulbs, Protective Shielding (repeated violation)
Observation: Ceiling light shield in the bakery observed in need of repair.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Intensity/Lighting (repeated violation)
Observation: A light in the cook-line ventilation system was observed not working.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
|
04/08/2014 | Follow-up | |
Facility uses food coloring in some baked goods. The person in charge went out to purchase a food labeling machine during the time of inspection. Provide further details for the cooking procedure of the dried beef jerky that was observed held individually wrapped under refrigeration. A product assessment may also be required for the beef jerky. A recheck will be conducted.
- Eating, Drinking, or Using Tobacco/Food Contamination Prevention (corrected on site)
Observation: Open drink containers observed stored on the food preparation table(s).
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Food Storage Containers, Identified with Common Name of Food
Observation: Container of cooking oil observed not properly labeled.
Correction: Except for containers holding food that can be readily and unmistakably recognized such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be identified with the common name of the food. Consumers may be allergic to certain foods or ingredients. The mistaken use of an ingredient, when the consumer has specifically requested that it not be used, may result in severe medical consequences. The mistaken use of food from unlabeled containers could result in chemical poisoning.
- Critical: Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Container of spinach and a container of spicy lintel in the hot holding cabinet observed at improper temperature (product was reheated by the person in charge).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Garlic sauce, cut tomatoes, injera with tomatoes, and cooked lentils located in the cook-line preparation unit observed cold holding at improper temperature (product was discarded by the person in charge).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Food Labels/Labeling (repeated violation)
Observation: Food packaged in the establishment is not labeled as specified in law (coffee, shiro, ground lentils, etc.)
Correction: Food packaged in a food establishment, shall be labeled as specified in law, including 21 CFR 101 – Food Labeling, and 9 CFR 317 Labeling, marking devices, and containers. The identity of a food in terms of origin and composition is important for instance when a food may be implicated in a foodborne illness and for nutritional information requirements. Ingredient information is needed by consumers who have allergies to certain food or ingredients.
- Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: The Kitfo on the menu is not properly labeled with the consumer advisory.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The cook-line preparation unit was observed not cold holding at proper temperature of 41 degrees Fahrenheit or below.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: There is no handsink located in the meat cutting section.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Light Bulbs, Protective Shielding
Observation: Ceiling light shield in the bakery observed in need of repair.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Intensity/Lighting
Observation: A light in the cook-line ventilation system was observed not working. Some lights in kitchen of the bakery observed not working.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Removing Dead or Trapped Birds, Insects, Rodents, and Other Pests
Observation: The hanging fly trap in the warewashing area observed in need of removal.
Correction: Dead or trapped birds, insects, rodents, and other pests shall be removed from control devices and the premises at a frequency that prevents their accumulation, decomposition, or the attraction of other pests. Dead rodents, birds, and insects must be removed promptly from the facilities to ensure clean and sanitary facilities and to preclude exacerbating the situation by allowing carcasses to attract other pests.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: Ceiling tiles throughout the bakery observed in need of cleaning. The floor surface behind the cook-line equipment observed in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: Cook-line ventilation filters observed in need of cleaning.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
|
03/25/2014 | Routine | |
- Critical: Hands and Arms/When to Wash (corrected on site) (repeated violation)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food. Corrected by instruction.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Compliance with Food Law/Sources (corrected on site)
Observation: Observed butter which was prepared in a private home offered for human consumption. Butter was taken out of display and no longer offered for sale or use.
Correction: Food prepared in a private home may not be used or offered for human consumption in a food establishment.
- Food Labels/Labeling (repeated violation)
Observation: Food packaged in the establishment is not labeled as specified in law.
Correction: Food packaged in a food establishment, shall be labeled as specified in law, including 21 CFR 101 – Food Labeling, and 9 CFR 317 Labeling, marking devices, and containers. The identity of a food in terms of origin and composition is important for instance when a food may be implicated in a foodborne illness and for nutritional information requirements. Ingredient information is needed by consumers who have allergies to certain food or ingredients.
- Cutting Surfaces (repeated violation)
Observation: The surfaces of the cutting boards and the prep unit cutting board are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: There are not an adequate number of handwashing sinks necessary for the convenient use by employees. There is no handwashing sink in the meat prep area.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: The floors under and behind equipment on the cookline are not cleaned as often as necessary to keep them clean. The hood needs cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
12/16/2013 | Follow-up | |
- Critical: Cooling, Cooked Food (corrected on site) (repeated violation)
Observation: Chick peas (48 F) and beef stew (67 F) which was cooked yesterday were not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less. Food was discarded.
- Cooling Methods
Observation: Methods used for cooling foods can not be accomplished with the time and temperature criteria. If using ice to cool, the food containers must be submerged in ice to cool properly.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Critical: Potentially Hazardous Food, Cold Holding
Observation: Raw meats observed cold holding at the improper temperatures of 47 F to 58 F in the bottom portion of the two door prep unit and cheese 59 F in top portion of the unit. Foods moved to other refrigeration units.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Food Labels/Labeling
Observation: Food packaged in the establishment is not labeled as specified in law.
Correction: Food packaged in a food establishment, shall be labeled as specified in law, including 21 CFR 101 – Food Labeling, and 9 CFR 317 Labeling, marking devices, and containers. The identity of a food in terms of origin and composition is important for instance when a food may be implicated in a foodborne illness and for nutritional information requirements. Ingredient information is needed by consumers who have allergies to certain food or ingredients.
- Food Temperature Measuring Devices
Observation: A food temperature measuring device is not provided and readily accessible for use in ensuring attainment and maintenance of food temperatures.
Correction: Food temperature measuring devices shall be provided and readily accessible for use in ensuring attainment and maintenance of food temperatures as specified under Chapter 3. The presence and accessibility of food temperature measuring devices is critical to the effective monitoring of food temperatures. Proper use of such devices provides the operator or person in charge with important information with which to determine if temperatures should be adjusted or if foods should be discarded.
- Equipment/Good Repair and Proper Adjustment
Observation: The two door prep unit on cookline is not maintained in a state of repair and condition that meets the requirements of materials for construction and repair and/or design.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Cutting Surfaces
Observation: The surfaces of the cutting boards and the prep unit cutting board are no longer effectively cleaned and sanitized.
Correction: Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they are not capable of being resurfaced. Cutting surfaces such as cutting boards and blocks that become scratched and scored may be difficult to clean and sanitize. As a result, pathogenic microorganisms transmissible through food may build up or accumulate. These microorganisms may be transferred to foods that are prepared on such surfaces.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The following nonfood-contact surfaces are not kept free of an accumulation of dust, dirt, food residue, and/or other debris:
-storage and display shelving
-shelving in the walk-in cooler
-table next to fryer
- bread display unit.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: Observed food containers, food processors, bowls and utensils stored as clean that were not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Cleaned equipment and utensils, laundered linens, and single-service and/or single-use articles are improperly stored on the floor.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Clean equipment and/or utensils are not stored in a self-draining position that allows air drying.
Correction: Clean equipment and utensils shall be stored as specified under paragraph (A) of this section and shall be stored: (1) In a self-draining position that allows air drying
- Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: There are not an adequate number of handwashing sinks necessary for the convenient use by employees. There is no handwashing sink in the meat prep area.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing sink in kitchen was observed being used for washing vegetables. Handwashing sink at serving bar being used for dumping. Corrected by instruction.
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Controlling Pests (Critical) (repeated violation)
Observation: Proper pest control methods are not used to minimize the presence of insects, rodents, and other pests found in the establishment. Observed roaches, rodent droppings and flies in facility.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by using methods, if pests are found, such as trapping devices or other means of pest control as specified under sections 7-202.12, 7-206.12, and 7-206.13. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
|
11/15/2013 | Routine | |
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee failed to wash his or her hands during food preparation when changing tasks.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Food Storage/Preventing Contamination from the Premises
Observation: Stored food is not protected from contamination. Several food boxes and containers were stored on the floor throughout the facility.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Food Display/Preventing Contamination by Consumers
Observation: Food on display is not protected from contamination. A self-service buffet station is set up and the containers are not covered with lids or protected by any sneezeguard.
Correction: Except for nuts in the shell and whole, raw fruits and vegetables that are intended for hulling, peeling, or washing by the consumer before consumption, food on display shall be protected from contamination by the use of packaging
- Consumer Self-Service Operations (corrected on site)
Observation: Consumer self-service operation for ready-to-eat foods is not provided with suitable utensils or effective dispensing methods. A customer was observed picking enjera bread with bare hands from underneath the plastic cover sheet.
Correction: Consumer self-service operations for ready-to-eat foods shall be provided with suitable utensils or effective dispensing methods that protect the food from contamination. Self-service operations of ready-to-eat foods provide an opportunity for contamination by consumers. The risk of contamination can be reduced by supplying clean utensils and dispensers and b y employee monitoring of these operations to ensure that the utensils and dispensers are properly used.
- Critical: Cooling, Cooked Food (repeated violation)
Observation: Spicy butter, observed at 53F in "Knox" walk-in refrigerator, was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
- Cooling Methods, Food containers (corrected on site)
Observation: Food container of beef stew and spaghetti were not arranged to provide maximum heat transfer and/or loosely covered, or uncovered while cooling.
Correction: When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (1) Arranged in equipment to provide maximum heat transfer through the container walls
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: A microwave and toaster oven in bakery area are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Temperature Measuring Devices
Observation: Two (2)-dr prep on cookline, 2-dr prep and "Superior" bakery 1-dr refrigerator are not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Sanitizing Solutions, Testing Devices (corrected on site)
Observation: A chlorine test kit or other device that accurately measures the concentration of the sanitizing solution is not provided.
Correction: A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Testing devices to measure the concentration of sanitizing solutions are required for 2 reasons: 1. The use of chemical sanitizers requires minimum concentrations of the sanitizer during the final rinse step to ensure sanitization
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean
Observation: The nonfood-contact surface of the doors and handles of refrigerators and freezers, inside of "True" bakery 3-door freezer and kitchen shelves is not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment and Utensils, Air-Drying Required
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Critical: Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: There are not an adequate number of handwashing sinks necessary for the convenient use by employees. There's no handwashing sink in meat cutting area.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Intensity/Lighting (repeated violation)
Observation: The light intensity is below 50 foot candles where a food employee is working with food (kitchen and bakery).
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Critical: Controlling Pests (Critical)
Observation: Flies observed in the kitchen.
Correction: The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by using methods, if pests are found, such as trapping devices or other means of pest control as specified under sections 7-202.12, 7-206.12, and 7-206.13. Insects and other pests are capable of transmitting disease to man by contaminating food and food-contact surfaces. Effective measures must be taken to control their presence in food establishments.
- Maintaining Premises, Unnecessary Items and Litter
Observation: The premises is not free of items that are unnecessary to the operation or maintenance of the establishment.
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: Floors and walls in kitchen are in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
07/23/2013 | Routine | |
- Critical: Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens (repeated violation)
Observation: The food establishment serves or sells raw or undercooked food and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: The Hamilton Beach food processor and the microwave are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Manual Warewashing/Sink Compartment Requirements (repeated violation)
Observation: The sink compartments are not large enough to accommodate immersion of the largest equipment and/or utensil.
Correction: Sink compartments shall be large enough to accommodate immersion of the largest equipment and utensils. If equipment or utensils are too large for the warewashing sink, a warewashing machine or alternative equipment as specified in paragraph (C) of this section shall be used. The 3 compartment sink requirement allows for proper execution of the 3-step manual warewashing procedure. If properly used, the 3 compartments reduce the chance of contaminating the sanitizing water and therefore diluting the strength and efficacy of the chemical sanitizer that may be used. Alternative manual warewashing equipment, allowed under certain circumstances and conditions, must provide for accomplishment of the same 3 steps: 1. Application of cleaners and the removal of soil
- Critical: Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: There are not an adequate number of handwashing sinks necessary for the convenient use by employees. No hand wash station at meat area.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
|
03/21/2013 | Follow-up | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Raw meat stored above enjera bread in meat display.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Critical: Cooling, Cooked Food (corrected on site) (repeated violation)
Observation: Cooked lamb dish in walk in, observed at 51oF, prepared previous day, was not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less. Discarded.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site)
Observation: Raw meat in meat display observed at 51oF. Relocated to walk in.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: The food establishment serves or sells raw or undercooked food and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Equipment and Utensils/Durability and Strength
Observation: The Hamilto Beach food processor and the microwave are not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Manual Warewashing/Sink Compartment Requirements
Observation: The sink compartments are not large enough to accommodate immersion of the largest equipment and/or utensil.
Correction: Sink compartments shall be large enough to accommodate immersion of the largest equipment and utensils. If equipment or utensils are too large for the warewashing sink, a warewashing machine or alternative equipment as specified in paragraph (C) of this section shall be used. The 3 compartment sink requirement allows for proper execution of the 3-step manual warewashing procedure. If properly used, the 3 compartments reduce the chance of contaminating the sanitizing water and therefore diluting the strength and efficacy of the chemical sanitizer that may be used. Alternative manual warewashing equipment, allowed under certain circumstances and conditions, must provide for accomplishment of the same 3 steps: 1. Application of cleaners and the removal of soil
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site) (repeated violation)
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in a chemical manual or mechanical operations, using a proper solution. Glass ware observed not being sanitized in 3 part bar sink.
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in chemical manual or mechanical operations, including the application of sanitizing chemicals by immersion, manual swabbing, brushing, or pressure spraying methods, using a solution as specified under section 4-501.114 by providing: (1) An exposure time of at least 10 seconds for a chlorine solution specified under paragraph 4-501.114(A), (2) An exposure time of at least 7 seconds for a chlorine solution of 50 mg/L that has a pH of 10 or less and a temperature of at least 38°C (100°F) or a pH of 8 or less and a temperature of at least 24°C (75°F), (3) An exposure time of at least 30 seconds for other chemical sanitizing solutions, or (4) An exposure time used in relationship with a combination of temperature, concentration, and pH that, when evaluated for efficacy, yields sanitization as defined in Subparagraph 1-201.10(B). Efficacious sanitization depends on warewashing being conducted within certain parameters. Time is a parameter applicable to both chemical and hot water sanitization. The time hot water or chemicals contact utensils or food-contact surfaces must be sufficient to destroy pathogens that may remain on surfaces after cleaning. Other parameters, such as rinse pressure, temperature, and chemical concentration are used in combination with time to achieve sanitization.
- Critical: Backflow Prevention, Air Gap
Observation: The diameter of the air gap between the water supply inlet and the flood level rim of the 3 part sink is less than 1 inch.
Correction: Provide an air gap with a diameter that is at least twice the diameter of the water supply inlet and not less than 1 inch for proper backflow prevention by the air gap.
- Critical: Handwashing Sinks/Numbers and Capacities (repeated violation)
Observation: There are not an adequate number of handwashing sinks necessary for the convenient use by employees. No hand wash station at meat area.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Handwashing Cleanser, Availability (corrected on site)
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink. No hand soap at bar hand sink.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap.
- Hand Drying Provision (repeated violation)
Observation: No hand towels at bar hand sink.
Correction: Each handwashing sink or group of adjacent handwashing sinks shall be provided with: (A) Individual, disposable towels
- Intensity/Lighting
Observation: Light burned out under hood.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
- Cleaning, Frequency and Restrictions
Observation: The area behind the grill was in need of cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
02/20/2013 | Routine | |
Restaurant representatives - add corrected or new information about Dama Market & Restaurant, 1503 Columbia Pike, Arlington, VA 22204 »