- Wiping Cloths, Use Limitation
Observation: The wiping cloths were not stored in a sanitizing solution.
Correction: Cloths in-use for wiping counters and other equipment surfaces shall be: (1) Held between uses in a chemical sanitizer solution at a concentration specified under section 4-501.114
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency (repeated violation)
Observation: The inside of the deep fryers need cleaning.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Handwashing Sink/Using/Operation and Maintenance (repeated violation)
Observation: The cooking line hand sink was blocked by a tray full with chicken wings.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Cleaning, Frequency and Restrictions
Observation: All floor corners/edges and behind the cooking line need cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
03/18/2016 | Routine | |
- Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Raw animal foods are not separated from each other during storage, preparation, holding, and/or display. Observed raw beef stored over fish in 3 door prep unit on mainline.
Correction: Food shall be protected from cross contamination by, except when combined as ingredients, separating types of raw animal foods from each other such as beef, fish, lamb, pork, and poultry during storage, preparation, holding, and display by: (a) Using separate equipment for each type, or (b) Arranging each type of food in equipment so that cross contamination of one type with another is prevented, and (c) Preparing each type of food at different times or in separate areas
- Cooling, Cooked Food (corrected on site)
Observation: Cooked chicken wings were not cooled within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
Correction: Cooked time/temperature control for safety food shall be cooled: (1) Within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surfaces of the slicer and some soiled equipment stored as clean are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site) (repeated violation)
Observation: Surfaces of the ice machine, and soda nozzles throughout establishment are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Handwashing Signage (corrected on site)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Poisonous or Toxic Material Containers/Container Prohibitions (corrected on site)
Observation: A container previously used to store poisonous or toxic materials is used to store, transport, or dispense food. Observed sanitizer spray bottle being used for cooking oil.
Correction: A container previously used to store poisonous or toxic materials may not be used to store, transport, or dispense food. Use of poisonous or toxic material containers to store, transport, or dispense food is prohibited because of the potential for contamination of food. The risk of serious medical consequences to anyone consuming food stored in these containers coupled with the lack of confidence that all of the material could or would be removed in the wash and sanitizing procedures are reasons for prohibiting this practice.
|
11/17/2015 | Risk Factor | |
Please service True 3 door prep unit. Do not use unit to store TCS foods until an ambient temperature of 41 or below is achieved. Please fax/email a copy of invoice.
- Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Raw animal foods are not separated from each other during storage, preparation, holding, and/or display.Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods.Observed raw chicken over fish, raw beef over fish, and raw chicken over vegetables.
Correction: Food shall be protected from cross contamination by, except when combined as ingredients, separating types of raw animal foods from each other such as beef, fish, lamb, pork, and poultry during storage, preparation, holding, and display by: (a) Using separate equipment for each type, or (b) Arranging each type of food in equipment so that cross contamination of one type with another is prevented, and (c) Preparing each type of food at different times or in separate areas
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: Observed several foods in "True" 3/dr prep cold holding at the improper temperatures of 46-58F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, TCS, Date Marking/On-Premises Preparation (corrected on site)
Observation: Humus, chicken wings, and other foods prepared and held in the food establishment for more than 24 hours is not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surfaces of several utensils and food containers stored clean are not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site) (repeated violation)
Observation: Surfaces of the can opener and soda nozzles at the bar and fountain are not clean.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Equipment/Cooking and Baking/Cleaning Frequency (corrected on site)
Observation: The cavity and/or door seal of the microwave oven is not cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure..
Correction: The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure. Food-contact surfaces of cooking equipment must be cleaned to prevent encrustations that may impede heat transfer necessary to adequately cook food. Encrusted equipment may also serve as an insect attractant when not in use. Because of the nature of the equipment, it may not be necessary to clean cooking equipment as frequently as the equipment specified in section 4-602.11.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located on mainline is not maintained so that it is accessible at all times for employee use. Observed a pan inside of sink.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Cleaning of Plumbing Fixtures (corrected on site)
Observation: Plumbing fixtures are not clean on handwashing sink on mainline.
Correction: Plumbing fixtures such as handwashing sinks, toilets, and urinals shall be cleaned as often as necessary to keep them clean and maintained and used as specified under section 5-205.11. Handwashing facilities are critical to food protection and must be maintained in operating order at all times so they will be used.
- Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
08/10/2015 | Risk Factor | |
- Hands and Arms/When to Wash (corrected on site)
Observation: Dirty gloves used with raw chicken not taken off prior to handling clean pans.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Food Storage/Preventing Contamination from the Premises
Observation: Food observed on floor of walk-in.
Correction: Store food where it is not exposed to splash, dust, or other contamination and/or install an approved, durable and cleanable barrier between the splash source and the food to prevent contamination.
- Cooling Methods (corrected on site)
Observation: Sliced tomatoes are not cooled properly after slicing.
Correction: Cooling shall be accomplished in accordance with the time and temperature criteria specified under section 3-501.14 by using one or more of the following methods based on the type of food being cooled: (1) Placing food in shallow pans
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site) (repeated violation)
Observation: The following items observed at improper cold holding temperatures in the BevAir 3-door reach-in: sliced tomatoes (46F), blue cheese dressing (46F), turkey (47F), mac & cheese (48F).
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment and Utensils/Durability and Strength (repeated violation)
Observation: Rice cooker is non-commercial.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Good Repair and Proper Adjustment
Observation: Knob on grill missing, ice cream freezer lid is broken (needs to be defrosted), and BevAir 3-door reach-in prep observed not holding foods at 41 or below.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment Food-Contact Surfaces and Utensils/Time Temperature Control For Safety Food/Cleaning Frequency (corrected on site)
Observation: Interior of ice machine, interior floors of both upright freezers, and soda nozzles observed to need cleaning.
Correction: Except when dry cleaning methods are used as specified under section 4-603.11, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned: (1) At any time when contamination may have occurred
- Plumbing System/Maintained in Good Repair
Observation: Sanitizer basin of 3-compartment sink leaks.
Correction: A plumbing system shall be maintained in good repair. Improper repair or maintenance may result in the creation of obnoxious odors or nuisances, and may also adversely affect the operation of warewashing equipment or other equipment which depends on sufficient volume and pressure to perform its intended functions.
- Light Bulbs, Protective Shielding
Observation: Light shielding missing by 3-compartment sink.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Intensity/Lighting (repeated violation)
Observation: Several lights out in kitchen, including under exhaust hood.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
|
02/18/2015 | Routine | |
- Critical: Hands and Arms/When to Wash
Observation: A food employee failed to wash her hands before donning gloves for working with food.
Correction: Instruct food employees to clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles (A) After touching bare human body parts other than clean, exposed portions of arms (B) After using the toilet room (C) After caring for or handling service animals or aquatic animals as specified in 2-403.11(B) (D) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking (E) After handling soiled equipment or utensils (F) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks (G) When switching between working with raw food and working with ready-to-eat food (H) Before donning gloves for working with food and (I) After engaging in other activities that contaminate the hands.
- Critical: Cooling, Cooked Food (corrected on site)
Observation: Chicken wings were not cooled within 2 hours from 57ºC (135ºF) to 21ºC (70ºF)
Correction: and/or within a total of 6 hours from 57ºC (135ºF) to 5ºC (41ºF) or less.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Blue cheese at 51 F, sliced tomatoes at 48 F. Discarded.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment and Utensils/Durability and Strength
Observation: The small rice cooker is not designed and constructed to be durable.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The inside of the True reach-in cooling unit needs cleaning. The hood fire suppression tank is greasy.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Critical: Equipment/Food-Contact/Before Use After Cleaning/Sanitized
Observation: The dishwasher machine was not ejecting sanitizer.
Correction: Utensils and food-contact surfaces of equipment shall be sanitized before use after cleaning. Sanitization is accomplished after the warewashing steps of cleaning and rinsing so that utensils and food-contact surfaces are sanitized before coming in contact with food and before use.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site) (repeated violation)
Observation: The handwashing sink located at the cooking line is not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
- Intensity/Lighting
Observation: The light intensity is below 50 foot candles where a food employee is working with food, the kitchen hood has three lights out.
Correction: The light intensity shall be at least 540 lux (50 foot candles) at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. Lighting levels are specified so that sufficient light is available to enable employees to perform certain functions such as reading labels
|
10/22/2014 | Routine | |
- Consumer Advisory/Consumption of Animal Foods that are Raw, Undercooked, or Not Otherwise Processed to Eliminate Pathogens
Observation: The food establishment serves or sells raw or undercooked food and the permit holder does not inform consumers of the significantly increased risk consuming such foods by way of a disclosure and reminder using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. No consumer advisory information on CG Brunch Menu for eggs available undercooked on some menu items.
Correction: The permit holder shall inform consumers of the significantly increased risk of consuming such foods by way of a disclosure and reminder, as specified in paragraphs (B) and (C) of this section using brochures, deli case or menu advisories, label statements, table tents, placards, or other effective written means. (B) Disclosure shall include: (1) A description of the animal-derived foods, such as "oysters on the half shell (raw oysters)," "raw-egg Caesar salad," and "hamburgers (can be cooked to order);" or (2) Identification of the animal-derived foods by asterisking them to a footnote that states that the items are served raw or undercooked, or contain (or may contain) raw or undercooked ingredients. (C) Reminder shall include asterisking the animal-derived foods requiring disclosure to a footnote that states: (1) Regarding the safety of these items, written information is available upon request
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees. Hand sink in ware washing area had no hand washing signage.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
12/27/2013 | Risk Factor | |
- Wiping Cloths, Use Limitation
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration
Correction: and/or not laundered daily.
- Critical: Equipment Food-Contact Surfaces and Utensils/Cleaning Frequency (Critical)
Observation: The inside of all cooling units and the inside the ice machine needs cleaning.
Correction: Surfaces of utensils and equipment contacting potentially hazardous food (time/temperature control for safety food) may be cleaned less frequently than every 4 hours if equipment is used for storage of packaged or unpackaged food such as a reach-in refrigerator and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues.
- Handwashing Sink/Using/Operation and Maintenance (repeated violation)
Observation: The handwashing sink located at the kitchen is not maintained so that it is accessible at all times for employee use.
Correction: A handwashing sink shall be maintained so that it is accessible at all times for employee use. Facilities must be maintained in a condition that promotes handwashing and restricted for that use. Convenient accessibility of a handwashing facility encourages timely handwashing which provides a break in the chain of contamination from the hands of food employees to food or food-contact surfaces.
|
04/25/2013 | Routine | |
Eliminate fruit/sewer fly harborage at the bar.
- Responsibilities of Owner or Proprietor
Observation: Absence of no-smoking signs or international no-smoking signs in non-smoking area.
Correction: Post no-smoking signs or international no-smoking signs in the non-smoking area.
These can be found online at www.vdh.virginia.gov/breatheasy
- Critical: Eating, Drinking, or Using Tobacco/Food Contamination Prevention
Observation: An open beverage container and/or a closed beverage container not handled to prevent contamination of a food employee's hands, the container, exposed food, and/or clean equipment was observed.
Correction: A food employee may drink from a closed beverage container if the container is handled to prevent contamination of: (1) The employee's hands
- Critical: Potentially Hazardous Food, Cold Holding
Observation: Cream cold holding at the improper temperature of 50ºF in the "True" 2-door counter refrigerator. Sliced cheese cold holding at the improper temperature s of 51-59ºF vertical stacked in the top portion of the "True" 2-door prep refrigerator.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Sanitized/Hot Water and Chemical/Methods (repeated violation)
Observation: When tested, a low concentration of chemical sanitizer was found in the sanitize basin of the kitchen and bar dishmachines.
Correction: Provide chlorine at proper concentration of 50-100 ppm and immerse or expose food contact surfaces to sanitizing solution for adequate time.
- Handwashing Sink/Using/Operation and Maintenance
Observation: The handwashing sink at the outside bar is used for purposes other than handwashing [dumpsink].
Correction: A handwashing sink may not be used for purposes other than handwashing. Sinks used for food preparation and warewashing can become sources of contamination if used as handwashing facilities by employees returning from the toilet or from duties which have contaminated their hands.
- Handwashing Cleanser, Availability
Observation: A supply of hand cleaning liquid, powder, or bar soap is not provided at each handwashing sink [outside bar].
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
- Hand Drying Provision
Observation: Each handwashing sink is not provided with individual, disposable towels
Correction: a continuous towel system that supplies the user with a clean towel
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees [outside bar].
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Critical: Poisonous or Toxic Materials/Common Name/Working Containers (corrected on site) (repeated violation)
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
08/24/2011 | Risk Factor Assessment | |
Restaurant representatives - add corrected or new information about Clarendon Grill, 1101 N Highland St, Arlington, VA 22201 »