1. Light intensity is less than 50 foot candles throughout the kitchen.
2. Floor tiles of the entire kitchen are cracked.
3. The wall behind 3-compartment sink is in need of cleaning and not maintained in good repair.
4. Avoid bare hand contact with ready-to-eat foods.
5. Clean the corners and edges of the floor and walls.
- Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Sliced cheese (48F), stacked too much too high on the top portion of the "Beverage Air" 3-dr prep and cooked noodles (46F) inside the "True" sliding doors refrigerators were observed at improper cold holding temperature.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact surfaces of the slicer blade assembly and can opener is not clean to sight and touch.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Handwashing Sink/Using/Operation and Maintenance (corrected on site)
Observation: The handwashing station at the kitchen/bar being used as a dump station.
Correction: The handwashing facility identified above is to be used for washing hands only.
- Food Manager Certificate and Responsibility
Observation: The food establishment is not under the immediate control of a Northern Virginia certified food manager.
Correction: It shall be unlawful to operate a food establishment unless it is under the immediate control of a Northern Virginia certified food manager
|
10/15/2015 | Risk Factor | |
- In-Use Utensils, Between-Use Storage (corrected on site)
Observation: Knives are improperly stored between the wall and prep table.
Correction: During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: (A) In the food with their handles above the top of the food and the container
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface rusty walk-in shelves is not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: The nonfood-contact surface of the storage shelves is not kept free of an accumulation of dust, dirt, food residue, and/or other debris.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: Encrusted grease deposits and/or other soil accumulations were observed on the food-contact surfaces of the baking sheet pans.
Correction: The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur and to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Light Bulbs, Protective Shielding (repeated violation)
Observation: The light bulbs above the wait station is not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Physical Facilities/Repairing (repeated violation)
Observation: Several kitchen floor are cracked. Threshold to walk-in refrigerator is not maintained in good repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
|
04/22/2015 | Routine | |
The inside of the reach-in freezer needs cleaning.
No violation noted during this evaluation. | 10/15/2014 | Risk Factor | |
Follow up to be conducted to verify servicing of walk in box for proper cold holding temperatures on or after 6/18/14.
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Lobster tail, crab cakes, wings, cold holding at the improper temperature of 45 F, 46 F, 44 F in walk in. Call for service placed to technician during inspection.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment, Food-Contact Surfaces, and Utensils (corrected on site)
Observation: The food-contact equipment surface(s) of the slicer blade assembly is(are) not clean to sight and touch. Equipment broken down for cleaning.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
|
06/11/2014 | Risk Factor | |
- Equipment/Good Repair and Proper Adjustment
Observation: The bottom wire shelf was rusty.
The men's restroom hand sink caulking was in disrepair.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Light Bulbs, Protective Shielding
Observation: The light bulb above the wait station was not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees. No hand washing sign at men's restroom.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Ventilation Systems/Cleaning/Nuisance and Discharge Prohibition
Observation: The kitchen exhaust fan cover was in need of cleaning.
Correction: Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt and other materials. Both intake and exhaust ducts can be a source of contamination and must be cleaned regularly. Filters that collect particulate matter must be cleaned or changed frequently to prevent overloading of the filter.
- Poisonous or Toxic Materials/Restrictions/Presence and Use (corrected on site)
Observation: Raid and Terminex insect spray are not required for the operation and maintenance of the food establishment. Discarded.
Correction: Only those poisonous or toxic materials that are required for the operation and maintenance of the establishment, such as for the cleaning and sanitizing of equipment and utensils and the control of insects and rodents, shall be allowed in the food establishment. This section does not apply to packaged poisonous or toxic materials that are for retail sale. The presence in the establishment of poisonous or toxic materials that are not required for the maintenance and operation of the establishment represents an unnecessary risk to both employees and consumers. Preserving food safety depends in part on the appropriate and proper storage and use of poisonous or toxic materials that are necessary to the maintenance and operation of a food establishment. Even those that are necessary can pose a hazard if they are used in a manner that contradicts the intended use of the material as described by the manufacturer on the material's label. If additional poisonous or toxic materials are present, there is an unwarranted increased potential for contamination due to improper storage (e.g., overhead spillage that could result in the contamination of food, food-contact surfaces, or food equipment) or inappropriate application.
|
02/18/2014 | Routine | |
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Observed foods in the walk-in cooler cold holding at improper temperatures (cheese 46 F, half/half 46, mashed potatoes 45). Foods moved to another refrigerator unit.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Critical: Equipment, Food-Contact Surfaces, and Utensils (Critical) (corrected on site)
Observation: The plastic containers used for food storage in the walk-in cooler are not clean to sight and touch. Containers taken to dish wash area for cleaning.
Correction: Equipment food-contact surfaces and utensils shall be clean to sight and touch. The objective of cleaning focuses on the need to remove organic matter from food-contact surfaces so that sanitization can occur.
- Critical: Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers (spray bottles) used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
10/29/2013 | Risk Factor | |
1. Bags of dirty linens and dish racks observed stored on the floor - (corrected).
2. Do not use corn husk brooms.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Sliced cheese (46F), Crabmeat (45F) in "Beverage Air" 3-door prep refrigerator were observed at improper cold holding temperature.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
|
06/19/2013 | Risk Factor | |
- Ice Used as Exterior Coolant, Prohibited as Ingredient/Preventing Contamination
Observation: Ice used as a medium for cooling the exterior surfaces of food is also used as food. Ice used for consumption is also used to cool cooling plate.
Correction: After use as a medium for cooling exterior surfaces of food such as melons or fish, packaged foods such as canned beverages, or cooling coils and tubes of equipment, ice may not be used as food. Ice that has been in contact with unsanitized surfaces or raw animal foods may contain pathogens and other contaminants. For example, ice used to store or display fish or packaged foods could become contaminated with microbes present on the fish or packaging. If this ice is then used as a food ingredient, it could contaminate the final product.
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Half and half in bar cooler observed at 47F.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Temperature Measuring Devices
Observation: The True freezer and Tappan freezer are not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Fixed, Spacing or Sealing (repeated violation)
Observation: Hand sink is women's restroom is not sealed to its adjoining wall.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment/Good Repair and Proper Adjustment
Observation: 1. Bar reach-in cooler observed at 45F. It is not capable of maintaining foods at 41F or below.
2. Shelving in walk-in is rusty.
3. Bottom shelf of Tappan upright freezer observed with rust.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils/Clean (repeated violation)
Observation: Fan above dish area observed with large dust accumulation.
Correction: Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. The objective of cleaning focuses on the need to remove soil from nonfood contact surfaces so that pathogenic microorganisms will not be allowed to accumulate and insects and rodents will not be attracted.
- Critical: Sanitized/Hot Water and Chemical/Methods (corrected on site)
Observation: After being cleaned, equipment food-contact surfaces and utensils are not sanitized in a chemical manual or mechanical operations, using a proper solution. Dish machine is not sanitizing.
Correction: After being cleaned, equipment food-contact surfaces and utensils shall be sanitized in chemical manual or mechanical operations, including the application of sanitizing chemicals by immersion, manual swabbing, brushing, or pressure spraying methods, using a solution as specified under section 4-501.114 by providing: (1) An exposure time of at least 10 seconds for a chlorine solution specified under paragraph 4-501.114(A), (2) An exposure time of at least 7 seconds for a chlorine solution of 50 mg/L that has a pH of 10 or less and a temperature of at least 38°C (100°F) or a pH of 8 or less and a temperature of at least 24°C (75°F), (3) An exposure time of at least 30 seconds for other chemical sanitizing solutions, or (4) An exposure time used in relationship with a combination of temperature, concentration, and pH that, when evaluated for efficacy, yields sanitization as defined in Subparagraph 1-201.10(B). Efficacious sanitization depends on warewashing being conducted within certain parameters. Time is a parameter applicable to both chemical and hot water sanitization. The time hot water or chemicals contact utensils or food-contact surfaces must be sufficient to destroy pathogens that may remain on surfaces after cleaning. Other parameters, such as rinse pressure, temperature, and chemical concentration are used in combination with time to achieve sanitization.
- Equipment and Utensils, Air-Drying Required
Observation: After cleaning and sanitizing, equipment and utensils are not air-dried, adequately drained, and/or they are cloth dried before contact with food.
Correction: After cleaning and sanitizing, equipment and utensils: (A) Shall be air-dried or used after adequate draining as specified in the first paragraph of 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (food-contact surface sanitizing solutions), before contact with food
- Equipment, Utensils, Linens, and Single-Service and Single-Use Articles/Storing
Observation: Dish racks observed stored on floor.
Correction: Cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored: (1) In a clean, dry location
- Refuse/Covering Receptacles
Observation: Receptacles and/or waste handling units for refuse, recyclables, and/or returnables kept outside the food establishment are not kept covered with tight-fitting lids or doors. One door is broken.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
- Outer Openings, Protected
Observation: Gap observed along the bottom threshold of door (down stairwell where chemicals are stored).
Correction: Outer openings of a food establishment shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Intensity/Lighting
Observation: Light is out in Tappan upright freezer.
Correction: The light intensity shall be at least 215 lux (20 foot candles): (1) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption, (2) Inside equipment such as reach-in and under-counter refrigerators
- Physical Facilities/Repairing
Observation: Threshold to walk-in is in poor repair.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Critical: Licenses for Food Establishments
Observation: The food establishment does not have a valid license.
Correction: No person shall operate a food establishment who does not have a valid license issued to him by the county manager. Only a person who complies with the requirements of this chapter shall be entitled to receive or retain such a license. Licenses are not transferable. A valid license shall be posted in every food establishment in a conspicuous place.
|
01/24/2013 | Routine | |
Restaurant representatives - add corrected or new information about Quarter Deck Restaurant, 1200 N Fort Myer Dr, Arlington, VA 22209 »