Tamales are not sold in the establishment anymore.
Wet mop mouse droppings.
The CFM states the container holding the quesadilla salvadorena (source from Arlington bakery) is returned to the supplier to be washed, rinsed, and sanitized.
- Nonfood-Contact Surfaces (repeated violation)
Observation: Store containers and boxes off the floor at least 6 inches (soda crates used as shelving).
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
- Handwashing Sinks/Numbers and Capacities (corrected on site)
Observation: Chemically treated towellettes for handwasing are not provided.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Controlling Pests (corrected on site)
Observation: Mouse droppings were observed under the chip shelf.
Correction: The premises shall be maintained free of insects, rodents, and other pests. The presence of insects, rodents, and other pests shall be controlled to eliminate their presence on the premises by eliminating harborage conditions.
|
01/04/2016 | Routine | |
Quesadilla bead (no cheese) is supplied by El Fulgarito in Md. The bread is delivered in a container and sold by the gloved CFM.
- Time/Temperature Control for Safety Food, Hot Holding (corrected on site)
Observation: Tamales hot holding at the improper temperature of 123ºF. The CFM accidentally turned the tamales on low. The tamales were reheated in the cooking warmer.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 57ºC (135ºF) or above, except that roasts cooked to a temperature and for a time specified in paragraph 3-401.11(B) or reheated as specified in paragraph 3-403.11(E) may be held at a temperature of 54ºC (130ºF) or above. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Temperature Measuring Devices
Observation: The walk in cooler is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Maintaining Premises, Unnecessary Items and Litter (repeated violation)
Observation: The premises is not free of items that are unnecessary to the operation or maintenance of the establishment (storage room).
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
|
01/09/2015 | Routine | |
1. A new mop sink has been installed.
2. Please seal the mop sink to its adjoining wall.
Significant compliance observed since last inspection.
- Utility Lines/Floors, Walls, and Ceilings (repeated violation)
Observation: Exposed utility service lines in cashier area are installed in a manner that obstructs or prevents cleaning of the floors, walls, or ceilings.
Correction: Exposed utility service lines and pipes shall be installed so they do not obstruct or prevent cleaning of the floors, walls, or ceilings. Floors that are of smooth, durable construction and that are nonabsorbent are more easily cleaned. Requirements and restrictions regarding floor coverings, utility lines, and floor/wall junctures are intended to ensure that regular and effective cleaning is possible and that insect and rodent harborage is minimized.
|
02/25/2014 | Follow-up | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Raw eggs stored over milk and papusas in walk-in refrigerator.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Nonfood-Contact Surfaces (repeated violation)
Observation: The nonfood-contact surface of the milk and beverage crates, used storage and shelving, is not free of unnecessary ledges, projections, and crevices, and/or designed and constructed to be easily cleanable or maintained.
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
- Temperature Measuring Devices (repeated violation)
Observation: The "Imbera" glass door reach-in refrigerator is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The gaskets of walk-in refrigerator are torn.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: All chest freezers are in need of defrosting and cleaning.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Handwashing Sinks/Numbers and Capacities
Observation: There is no mop sink or curbed facility equipped with a floor drain provided and/or conveniently located for the cleaning of mops or similar wet floor cleaning tools and for the disposal of mop water and similar liquid wastes. The PIC said that toilet is used to dump mop water.
Correction: At least 1 handwashing sink, a number of handwashing sinks necessary for their convenient use by employees in food preparation, food dispensing, warewashing areas, and in, or immediately adjacent to toilet rooms
- Refuse/Toilet Room Receptacle, Covered
Observation: There is no covered receptacle in the toilet room used by females.
Correction: A toilet room used by females shall be provided with a covered receptacle for sanitary napkins. Garbage containers should be available wherever garbage is generated to aid in the proper disposal of refuse.
- Utility Lines/Floors, Walls, and Ceilings
Observation: Exposed utility service lines in cashier area are installed in a manner that obstructs or prevents cleaning of the floors, walls, or ceilings.
Correction: Exposed utility service lines and pipes shall be installed so they do not obstruct or prevent cleaning of the floors, walls, or ceilings. Floors that are of smooth, durable construction and that are nonabsorbent are more easily cleaned. Requirements and restrictions regarding floor coverings, utility lines, and floor/wall junctures are intended to ensure that regular and effective cleaning is possible and that insect and rodent harborage is minimized.
- Light Bulbs, Protective Shielding
Observation: The light bulbs in the walk-in refrigerator are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Toilet Rooms, Enclosed (repeated violation)
Observation: The toilet room is not completely enclosed and/or provided with a tight-fitting and/or self-closing door. Self-closing mechanism is missing on the toilet room door.
Correction: Except where a toilet room is located outside a food establishment and does not open directly into the food establishment such as a toilet room that is provided by the management of a shopping mall, a toilet room located on the premises shall be completely enclosed and provided with a tight-fitting and self-closing door. Completely enclosed toilet facilities minimize the potential for the spread of disease by the movement of flies and other insects between the toilet facility and food preparation areas.
- Handwashing Signage (corrected on site) (repeated violation)
Observation: A sign or poster that notifies food employees to wash their hands is not provided at toilet room handwashing sink used by food employees and/or is not clearly visible to food employees.
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Maintaining Premises, Unnecessary Items and Litter (repeated violation)
Observation: The premises is not free of items that are unnecessary to the operation or maintenance of the establishment. An unused refrigerator is stored inside walk-in, a 2-glass door refrigerator by entrance to walk-in and other unnecessary items are stored in the back storage room.
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
- Critical: Pesticides/Rodent Bait Stations (corrected on site)
Observation: Rodent bait is not contained in a covered and tamper-resistant bait station. Loose rodent pellets , placed on white paper, were observed stored over milk and other foods on walk-in shelves.
Correction: Rodent bait shall be contained in a covered, tamper-resistant bait station. Open bait stations may result in the spillage of the poison being used. Also, it is easier for pests to transport the potentially toxic bait throughout the establishment. Consequently, the bait may end up on food-contact surfaces and ultimately in the food being prepared or served.
|
01/16/2014 | Routine | |
- Equipment and Utensils/Durability and Strength
Observation: Imbera glass reach-in is not designed to store potentially hazardous foods/temperature control for safety foods.
Correction: Equipment and utensils shall be designed and constructed to be durable and to retain their characteristic qualities under normal use conditions. Equipment and utensils must be designed and constructed to be durable and capable of retaining their original characteristics so that such items can continue to fulfill their intended purpose for the duration of their life expectancy and to maintain their easy cleanability. If they can not maintain their original characteristics, they may become difficult to clean, allowing for the harborage of pathogenic microorganisms, insects, and rodents. Equipment and utensils must be designed and constructed so that parts do not break and end up in food as foreign objects or present injury hazards to consumers. A common example of presenting an injury hazard is the tendency for tines of poorly designed single service forks to break during use.
- Nonfood-Contact Surfaces
Observation: Milk and soda crates are used as shelving..
Correction: Nonfood-contact surfaces shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance. Hard-to-clean areas could result in the attraction and harborage of insects and rodents and allow the growth of foodborne pathogenic microorganisms. Well-designed equipment enhances the ability to keep nonfood-contact surfaces clean.
- Temperature Measuring Devices
Observation: The Imbera glass reach-in is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Fixed, Spacing or Sealing
Observation: Restroom hand sink is not sealed to its adjoining wall. Owner advised he is going to replace the hand sink.
Correction: Equipment that is fixed because it is not easily movable shall be installed so that it is: (1) Spaced to allow access for cleaning along the sides, behind, and above the equipment
- Equipment/Good Repair and Proper Adjustment
Observation: The following observed in need of repair:
- gasket to walk-in
- walk-in observed at 47F- CORRECTED, unit was turned down.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Service Sink/Numbers and Capacities
Observation: There is no service sink or curbed cleaning facility equipped with a floor drain provided and/or conveniently located for the cleaning of mops or similar wet floor cleaning tools and for the disposal of mop water and similar liquid wastes.
- Hand sink in restroom is used as mop sink.
Correction: At least 1 service sink or 1 curbed cleaning facility equipped with a floor drain shall be provided and conveniently located for the cleaning of mops or similar wet floor cleaning tools and for the disposal of mop water and similar liquid wastes. Mop water and similar liquid wastes are contaminated with microorganisms and other filth. Waste water must be disposed of in a sanitary manner that will not contaminate food or food equipment. A service sink or curbed cleaning facility with a drain allows for such disposal.
- Toilet Rooms, Enclosed
Observation: Restroom door is not self-closing.
Correction: Except where a toilet room is located outside a food establishment and does not open directly into the food establishment such as a toilet room that is provided by the management of a shopping mall, a toilet room located on the premises shall be completely enclosed and provided with a tight-fitting and self-closing door. Completely enclosed toilet facilities minimize the potential for the spread of disease by the movement of flies and other insects between the toilet facility and food preparation areas.
- Handwashing Cleanser, Availability (corrected on site)
Observation: No soap at restroom hand sink.
Correction: Each handwashing sink or group of 2 adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Hand cleanser must always be present to aid in reducing microorganisms and particulate matter found on hands.
- Handwashing Signage
Observation: A sign or poster that notifies food employees to wash their hands is not provided at all handwashing lavatories used by food employees and/or is not clearly visible to food employees (restroom).
Correction: A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees. A sign or poster is required to remind food employees to wash their hands.
- Intensity/Lighting
Observation: Lights are out in walk-in.
Correction: The light intensity shall be at least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in the walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning. Properly distributed light makes the need for cleaning apparent by making accumulations of soil conspicuous.
- Maintaining Premises, Unnecessary Items and Litter
Observation: Unnecessary equipment observed:
- in back storage room
- unused refrigerator observed in walk-in.
Correction: The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment such as equipment that is nonfunctional or no longer used. The presence of unnecessary articles, including equipment which is no longer used, makes regular and effective cleaning more difficult and less likely. It can also provide harborage for insects and rodents.
|
11/26/2013 | Pre-Opening | |
Restaurant representatives - add corrected or new information about Family Quick Mart, 5555 Columbia Pike Suite 100, Arlington, VA 22204 »